FS S5810 Series User manual

MANAGED L3 ENTERPRISE SWITCHES
MANAGED L3 ENTERPRISE SWITCHES
SWITCHS MANAGEABLES L3 POUR ENTREPRISES
S5810 Series Switches
Quick Start Guide
Quick Start Anleitung
Guide de Démrrage Rapide
V1.0
MINICONSOLE
PoE
STATUSPWR1 PWR2 MGMT
50F
49F 52F
51F
SFP+
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16 32
15 18
17 20
19 22
21 24
23 26
25 28
27 30
29 31 48
34
33 36
35 38
37 40
39 42
41 44
43 46
45 47
MINICONSOLE
STATUSPWR1 PWR2 MGMT
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16
15 18
17 20
19 22
21 24
23 26
25 28
27 32F
26F
25F 28F
27F 30F
29F 31F
SFP+
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
S5810-48TS
S5810-28TS
On=Link Flashing=ACT Green=1000MYellow=10G/1G

Introduction
Thank you for choosing S5810 Series Switches. This guide is designed to familiarize you with the
layout of the S5810 Series Switches and describes how to deploy them in your network.
Accessories
S5810-28TS
Mounting Bracket x2 M4 Screw x8
Rubber Pad x4
Grounding Cable x1USB Cable x1
EN
1
MINICONSOLE
STATUSPWR1 PWR2 MGMT
50F49F 52F51F
SFP+
On=Link Flashing=ACT Green=1000MYellow=10G/1G
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16 32
15 18
17 20
19 22
21 24
23 26
25 28
27 30
29 31 48
34
33 36
35 38
37 40
39 42
41 44
43 46
45 47
MINICONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
S5810-48TS
S5810-28TS
S5810-48TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
Power Cord x2

Front Panel Ports
Hardware Overview
S5810-28TS
S5810-48TS
Port Description
A serial port for installing the software driver.MINI CONSOLE
CONSOLE
USB
MGMT
RJ45
SFP
SFP+
A RJ45 console port for serial management.
A USB management port for software configuration backup and offline software
upgrade.
An out-of-band Ethernet management port.
10/100/1000Base-T ports for Ethernet connection.
SFP ports for 100M/1000M connection.
SFP+ ports for 1/10G connection.
EN
2
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
MINI CONSOLE
CONSOLE
USB MGMT
RJ45
SFP
SFP+
S5810-28TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
Mounting Bracket x2 M4 Screw x8Rubber Pad x4
Grounding Cable x1USB Cable x1
Power Cord x2

Front Panel LEDs
LED State Description
The switch is powered off.
Status
PWR1/PWR2
MGMT
RJ45
Off
Blinking Green
(3Hz)
Blinking Green
(10Hz)
Solid Green
Solid Yellow
Solid Red
Off
Solid Green
Solid Yellow
Solid Red
Off
Solid Green
The power module is disconnected or the power is off.
The power module has been connected and can supply power.
The model of power module can be read but cannot be
identified.
The redundant power module is faulty or does not connect to an
AC cable.
The MGMT port is not linked.
The MGMT port is linking up at 1000Mbps.
Blinking Green The MGMT port is receiving and delivering data at 1000M.
Solid Yellow
Blinking Yellow
The MGMT port is linking up at 100/10M.
The MGMT port is receiving and delivering data at 100/10M.
Off The RJ45 Ethernet port is not linked.
Solid Green The RJ45 Ethernet port is linking up at 1000M.
Blinking Green The RJ45 Ethernet port is receiving and delivering data at 1000M.
The switch is initializing. The LED blinking frequency is 3Hz. If the
LED keeps blinking, the switch is abnormal.
Device live locating. It supports maintainers remote
enable/disable.
The switch is working properly.
The temperature of the air inlet/outlet beyond normal working
temperature.
The current power cannot support the whole system.
The switch is faulty.
EN
3
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M | Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
RJ45 SFP
SFP+
status PWR2
PWR1 MGMT
On=Link Flashing=ACT Green=1000M Yellow=10/100M
S5810-28TS

Front Panel Ports
S5810-48TS
Back Panel
RJ45
SFP
SFP+
Solid Yellow The RJ45 Ethernet port is linking up at 100/10M.
Blinking Yellow The RJ45 Ethernet port is receiving and delivering data at
100/10M.
Off The SFP port is not linked.
Solid Green The SFP port is linking up at 1000M.
Blinking Green The SFP port is receiving and delivering data at 1000M.
Solid Yellow The SFP port is linking up at 100M.
Blinking Yellow The SFP port is receiving and delivering data at 100M.
Off The SFP+ port is not linked.
Solid Green The SFP+ port is linking up at 10/1G.
Blinking Green The SFP+ port is receiving and delivering data at 10/1G.
PWR1 PWR2
Module1
Module2
Grounding Point Expansion Module Dual Power
EN
4
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
50F49F 52F51F
SFP+
On=Link Flashing=ACT Green=1000M Yellow=10G/1G
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16 32
15 18
17 20
19 22
21 24
23 26
25 28
27 30
29 31 48
34
33 36
35 38
37 40
39 42
41 44
43 46
45 47
MINI CONSOLE
CONSOLE
USB MGMT
RJ45
SFP+
S5810-48TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M

Front Panel LEDs
Ports Description
A serial port for installing the software driver.MINI CONSOLE
CONSOLE
USB
MGMT
RJ45
SFP+
A RJ45 console port for serial management.
A USB management port for software and configuration backup and offline
software upgrade.
An out-of-band Ethernet management port.
10/100/1000Base-T ports for Ethernet connection.
SFP+ ports for 1/10G connection.
LED State Description
The switch is powered off.
Status
PWR1/PWR2
Off
Blinking Green
(3Hz)
Blinking Green
(10Hz)
Solid Green
Solid Yellow
Solid Red
Off
Solid Green
Solid Yellow
Solid Red
The power module is disconnected or the power is off.
The power module has been connected and can supply power.
The model of power module can be read but cannot be
identified.
The redundant power module is faulty or does not connect to an
AC cable.
The switch is initializing. The LED blinking frequency is 3Hz. If the
LED keeps blinking, the switch is abnormal.
Device live locating. It supports maintainers remote
enable/disable.
The switch is working properly.
The temperature of the air inlet/outlet beyond normal working
temperature.
The current power cannot support the whole system.
The switch is faulty.
EN
5
MINI CONSOLE
STATUS PWR1 PWR2 MGMT
50F49F 52F51F
SFP+
On=Link Flashing=ACT Green=1000M Yellow=10G/1G
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16 32
15 18
17 20
19 22
21 24
23 26
25 28
27 30
29 31 48
34
33 36
35 38
37 40
39 42
41 44
43 46
45 47
RJ45
SFP+
status
PWR1 MGMT
PWR2
S5810-48TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M

Back Panel
MGMT
RJ45
Off
Solid Green
The MGMT port is not linked.
The MGMT port is linking up at 1000M.
Blinking Green The MGMT port is receiving and delivering data at 1000M.
Solid Yellow
Blinking Yellow
The MGMT port is linking up at 100/10M.
The MGMT port is receiving and delivering data at 100/10M.
Off The RJ45 Ethernet port is not linked.
Solid Green The RJ45 Ethernet port is linking up at 1000M.
Blinking Green The RJ45 Ethernet port is receiving and delivering data at 1000M.
Solid Yellow The RJ45 Ethernet port is linking up at 100/10M.
Blinking Yellow The RJ45 Ethernet port is receiving and delivering data at
100/10M.
SFP+
Off The SFP+ port is not linked.
Solid Green The SFP+ port is linking up at 10/1G.
Blinking Green The SFP+ port is receiving and delivering data at 10/1G.
PWR1 PWR2
Module1
Module2
Grounding Point Expansion Module Dual Power
Installation Requirements
Before installation, make sure that you have the followings:
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables for connecting network devices.
EN
6

Site Environment
Make sure that the temperature of installation site is maintained at 0°C~50°C.
The installation site must be well ventilated. Ensure that there is adequate air flow around
the switch.
Make sure that the switch is level and stable to avoid any hazardous conditions.
Make sure that the relative humidity of installation site is maintained at 10%~90%.
The installation site must be free from leaking, dripping water or heavy dew.
Keep the installation site dust-free.
Make sure that the rack and working platforms are well earthed.
Mounting the Switch
Desk Mounting
1. Attach four rubber pads to the bottom of switch.
2. Place the switch on a desk.
EN
7
MINICONSOLE
STATUSPWR1 PWR2MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F
25F 28F
27F 30F
29F 32F
31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
COMBO
21 43 65 87 21 43 65 87 109 1211 1413 1615 1817 2019
On=Link Flashing=ACT Green=1000M Yellow=10/100M
MGMT
CONSOLE
COMBO
65 87 21 43 65 7
On=Link Flashing=ACT Green=1000M Yellow=10/100M

1. Fix the mounting brackets to the two sides of the switch with eight M4 screws.
2. Fix the switch to the rack with M6 screws and cage nuts.
Rack Mounting
NOTE: For wall mounting, you need to turn the mounting brackets to 90°and fix them to
the two sides of the switch. Then mount the switch on the wall.
EN
8
SFP+
20 2221 2423 2625 2827 30F
29F 32F
31F
Green=1000M Yellow=100M Green=10G/1G
S5810-28TS
87 109 1211 1413
SFP+
1615 1817 2423 2625 2827 26F
25F 28F
27F 30F
29F 32F
31F
Green=1000M Yellow=100M Green=10G/1G
S5810-28TS
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
COMBO
21 43 65 87 21 43 65 87 109 1211 1413 1615 1817 2019 21
On=Link Flashing=ACT Green=1000M Yellow=10/100M
MGMT
CONSOLE

Wall Mounting
1. Fix the mounting brackets to the two sides of the switch with eight M4 screws.
2. Use the expansion screws to securely attach the mounting brackets on the wall.
Module1
EN
9
RG-S5750C-28GT4XS-H
Green=1000MYellow=100M | Green=10G/1G
On=LinkFlas hing=ACT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F
25F 28F
27F 30F
29F 32F
31F
SFP+
MGMT
CONSOLE
STATUSPWR1PWR2 MGMT
On=LinkFlashing=ACT Green=1000M Yellow=10/100M
S5810-28TS
MINICONSOLE
SFP+
2221 2423 2625 2827 30F29 32F31F
S5810-28TS

Installing the Power Supply Module
NOTE: 1. Insert the power module steadily.
2. Pay attention to the direction of insertion.
3. If the position is improper after inserting the power module, press the plug of the power
module and hold on to the handle with one hand to slowly pull it out, then re-insert it.
PWR1 PWR2
Module2
PWR1
1. Take a new power module out of the package and confirm the input mode and the input parameters
of the power module match the requirements.
2. Remove the old power module and take the plane printed with power information as the top panel
of the power module. Hold the handle of the power module with one hand, and hold the end of the
power module with the other hand.
3. Insert it into the power module slot along the guide rail uprightly and slowly until it totally inserts
into place(a“click” sound is heard), then make sure that the module is in good contact with the slot.
Module1
EN
10

Connecting the Power
Grounding the Switch
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Fix the grounding lug to the grounding point on the back panel of the switch with the washers and
screws.
PWR1
Module1
Module2
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
PWR1 PWR2
Module2
EN
11
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
COMBO
21 43 65 87 1
On=Link Flashing=ACT Green=1000M Yellow=10/100M
MGMT
CONSOLE

Connecting the RJ45 Ports
Connecting the SFP/SFP+ Port
1. Plug the AC power cord into the power port on the back panel of the switch.
2. Connect the other end of the power cord to an AC power source.
1. Connect one end of an Ethernet cable to the RJ45 port.
2. Connect the other end of the Ethernet cable to another network device.
PWR2
WARNING: Do not install power cord while the power is on.
EN
12
On=Link Flashing=ACT Green=1000M Yellow=10/100M
SFP+
COMBO
21 43 65 87 109 1211 1817 2019 2221 2423 2625 2827 26F
25F 28F
27F 30F
29F 32F
31F
Green=1000M Yellow=100M Green=10G/1G
S5810-28TS

Connecting the CONSOLE Port
Connecting the MGMT Port
1. Plug the compatible SFP/SFP+ optical module into the SFP/SFP+ port.
2. Connect one end of a fiber optic cable to the optical module. Then connect the other end of the
cable to another fiber device.
1. Insert the RJ45 connector of the console cable into the console port of the switch.
2. Connect the DB9 female connector of the console cable to the serial port of the computer.
1. Connect one end of a standard RJ45 Ethernet cable to the MGMT port of the switch.
2. Connect the other end of the cable to a computer.
WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules or
fiber optical cables without eye protection.
EN
13
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 10912
11
14
13 16
15 18
17 20
19 18
17 20
19 22
21 24
23
MGMT
CONSOLE
On=Link Flashing=ACT Green=1000M Yellow=10/100M
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 12
11
MGMT
CONSOLE

Stacking the Switches
Configuring the Switch
Configuring the Switch via the Web-based Interface
The S5810 series switches support stacking up to 8 switches between the same series together. The
switch can be physically stacked using optical fiber cables connected to SFP+ transceivers or 10G Direct
Attach Cables (DAC). Only four SFP+ uplinks on the switch can be used for physical stacking.
Step 1: Connect the computer to the Management port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x.(“x”is any number from 2 to 254.)
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses:
EN
14
S5810-28FS
MINICONSOLE
STATUSPWR1 PWR2MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
MINICONSOLE
STATUSPWR1 PWR2MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
MINICONSOLE
STATUSPWR1 PWR2MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
MINICONSOLE
STATUSPWR1 PWR2MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
26F25F 28F27F 30F29F 32F31F
26F25F 28F27F 30F29F 32F31F
26F25F 28F27F 30F29F 32F31F

Configuring the Switch via the Console Port
Step 1: Connect a computer to the switch's console port using the console cable.
Step 2: Start the terminal simulation software such as HyperTerminal on the computer.
Step 3: Set the parameters of the HyperTerminal: 9600 bits per second, 8 data bits, no parity, 1
stop bit and no flow control.
Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password,
admin/admin.
Step 4: Click Login to display the web-based configuration page.
Step 4: After setting the parameters, click Connect to enter.
IE 8/9/10/11, Google Chrome, Firefox are supported
Login
admin
*****
x
Quick Connect
Protocol:
The port may be manually entered or selected from the list.
Serial
Flow Control
DTR/DSR
RTS/CTS
XON/XOFF
Save sessionShow quick connect on startup
Open in a tab
Connect
Cancel
COM3
9600
8
None
1
Port:
Baud rate:
Data bits:
Parity:
Stop bits:
Name of pipe:
EN
15

Troubleshooting
All indicators on the front panel of the switch are off. The status indicator of the fan module is off.
The indicator on the panel of the power module is off. The fan does not work. First disconnect the
power cord of the power module, then check the following:
1. Check whether the console cable is correctly connected.
2. Check whether the console cable is broken.
3. Check whether the console port of the switch is the same as the port of the terminal device.
4. Check whether the console port configuration of the terminal device is correct.
1. Check whether the cable connections of the rack are correct.
2. Check whether the connection between the power socket and the power cord is loose.
3. Check whether the connection between the power module and the power cord is loose.
4. Check whether the power module inserts into place.
1. Test network connectivity through ping.
2. If the network is reachable, try restarting the switch.
3. Check whether the corresponding service enables.
1. Check whether the receiving and delivering of fiber optical cable connects correctly.
2. Check whether the wavelengths of optical modules of the interconnection are the same.
3. Check whether the distance of the interconnection is within the distance marked by the optical
module.
4. Check whether the rates of the interconnection are the same or whether the mode of port rate
is configured correctly for ports which support different rates.
5. Check whether the optical fiber type meets the requirements.
The Power Module Cannot Supply Power
Connecting the Switch Remotely Unsuccessfully
The Optical Port Cannot Link up
No Characters/Distorted Characters are Displayed on the Screen of the
Terminal Device
EN
16

Online Resources
Download
Help Center
Contact Us
https://www.fs.com/products_support.html
https://www.fs.com/service/fs_support.html
https://www.fs.com/contact_us.html
Product Warranty
Warranty: The S5810 series switches enjoy 3 years limited warranty against defect in
materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html
3
EN
17

Einführung
Vielen Dank, dass Sie sich für Switches der Serie S5810 entschieden haben. Diese Anleitung soll Sie
mit dem Aufbau der S5810 Series Switches vertraut machen und erklärt, wie Sie sie in Ihrem
Netzwerk einsetzen können.
Zubehör
S5810-28TS
Montagehalterung x2 M4-Schraube x8 Gummipad x4
USB-Kabel x1 Erdungskabel x1
DE
18
MINICONSOLE
STATUSPWR1 PWR2 MGMT
50F49F 52F51F
SFP+
On=Link Flashing=ACT Green=1000MYellow=10G/1G
CONSOLE
MGMT
2
14
36
58
710
912
11 14
13 16 32
15 18
17 20
19 22
21 24
23 26
25 28
27 30
29 31 48
34
33 36
35 38
37 40
39 42
41 44
43 46
45 47
MINICONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
S5810-28TS
S5810-48TS
S5810-28TS
S5810-48TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
On=Link Flashing=ACT Green=1000M Yellow=10/100M
Netzkabel x2

Ports an der Vorderseite
Hardware-Übersicht
S5810-28TS
S5810-48TS
Port Beschreibung
Ein serieller Port für die Installation des Softwaretreibers.MINI CONSOLE
CONSOLE
USB
MGMT
RJ45
SFP
SFP+
Ein RJ45-Console-Port für die serielle Verwaltung.
Ein USB-Verwaltungsport für die Sicherung der Softwarekonfiguration und die
Offline-Aktualisierung der Software.
Ein Out-of-Band-Ethernet-Verwaltungsport.
10/100/1000Base-T-Ports für den Ethernet-Anschluss.
SFP-Ports für 100M/1000M-Verbindungen.
SFP+-Ports für 1/10G-Verbindungen.
DE
19
MINI CONSOLE
STATUSPWR1 PWR2 MGMT
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 26F25F 28F27F 30F29F 32F31F
SFP+
Green=1000M Yellow=100M Green=10G/1G
On=Link Flashing=ACT
MGMT
CONSOLE
MINI CONSOLE
CONSOLE
USB MGMT
RJ45
SFP
SFP+
S5810-28TS
On=Link Flashing=ACT Green=1000M Yellow=10/100M
Montagehalterung x2 M4-Schraube x8
Gummipad x4
USB-Kabel x1 Erdungskabel x1
Netzkabel x2