FS S5860 Series User manual

MANAGED L3 ENTERPRISE SWITCHES
S5860 Series Switches
Quick Start Guide V1.0
MGMT
SYS PWR FAN PoE
1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=OverLoad
CONSOLE
Yellow=100M
S5860-48SC
1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F 28F 29F 30F 31F 32F 33F 34F 35F 36F 37F 38F 39F 40F 41F 42F 43F 44F 45F 46F 47F 48F
100G
49F 50F 51F 52F 53F 54F 55F 56F
Status ID
MGMT
CONSOLE 25G
STATUSPWR1PWR2 FANMGMT ID
1234
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40GBreakout
25
26
S5860-20SQ
40G
FUNC

Introduction
Thank you for choosing S5860 Series Switches. This guide is designed to familiarize you with the
layout of the switch and describes how to deploy the switch in your network.
Accessories
S5860-20SQ
S5860-20SQ/S5860-24XB-U
S5860-48SC
S5860-24XB-U
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
MGMT
CONSOLE 25G
STATUSPWR1PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
S5860-48SC
1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F 28F 29F 30F 31F 32F 33F 34F 35F 36F 37F 38F 39F 40F 41F 42F 43F 44F 45F 46F 47F 48F
100G
49F 50F 51F 52F 53F 54F 55F 56F
Status ID
Power Cord x2
Mounting Bracket x2 M4 Screw x8
Rubber Pad x4Grounding Cable x1

S5860-48SC
NOTE: S5860 series switches have dust plugs delivered with them. Keep the dust plugs
properly and use them to protect idle optical ports.
Hardware Overview
Front/Back Panel Ports
S5860-20SQ
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
USB CONSOLE QSFP+
MGMT SFP+ SFP28
Grounding Cable x1Power Cord x2 Mounting Bracket x2 M4 Screw x14
M6 Screw x8 M6 Nut x8 Inner Rail x2Slide Rail x2

S5860-48SC
Ports Description
RJ45
SFP+
SFP28
100M/1/2.5/5/10G ports for Ethernet connection
SFP+ ports for 1/10G connection
SFP28 ports for 10/25G connection
QSFP+
QSFP28
MGMT
QSFP+ ports for 40G or 4x 10G connection
QSFP28 ports for 40/100G connection
An out-of-band Ethernet management port
CONSOLE An RJ45 console port for serial management
USB A USB management port for software and conguration backup and oine
software upgrade
S5860-48SC
1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F 28F 29F 30F 31F 32F 33F 34F 35F 36F 37F 38F 39F 40F 41F 42F 43F 44F 45F 46F 47F 48F
100G
49F 50F 51F 52F 53F 54F 55F 56F
Status ID
USB
CONSOLE
SFP+ QSFP28
Status Status Status
Status
FUNC
ID
Link ACT
Status
PWR1
PWR2
1 2 3
4
MGMT
CONSOLE
AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB
MGMT
MGMT
S5860-24XB-U
USB CONSOLE RJ45 SFP+ SFP28
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=OverLoad
CONSOLE Yellow=100M

NOTE: The FUNC button of the S5860-48SC is reserved.
Ports Description
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
Front/Back Panel Buttons
S5860-20SQ
FUNC
Status Status Status
Status
FUNC
ID
Link ACT
Status
PWR1
PWR2
1 2 3
4
MGMT
CONSOLE
AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB
S5860-48SC
FUNC
S5860-24XB-U
PoE FUNC
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=OverLoad
CONSOLE Yellow=100M
Buttons Description
PoE
FUNC
Switch the display mode between PoE mode and switch mode.
The switch will restart after you press the FUNC button for more than ve
seconds and wait for another ten seconds.

S5860-20SQ
Back Panel
Front/Back Panel LEDs
LEDs Status Description
O
Solid Red
The system is powered o.
Blinking Green Initialization is in progress.
1. A system fault occurs.
2. The temperature reaches the upper limit.
STATUS
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
S5860-20SQ
40G
FUNC
Status Status Status
Status
FUNC
ID
Link ACT
Status
PWR1
PWR2
1 2 3
4
MGMT
CONSOLE
AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB
S5860-48SC
Grounding Point
Grounding Point
Fan Slots
Fan Slots
Dual Power Supplies
Dual Power Supplies
FAN1 FAN2 PWR1
M1SFANI-F
Status
M1SFANI-F
Status
M1SFANI-F
Status
M1SFANI-F
Status
M1SFANI-F
Status
FAN1 FAN2 FAN3 PWR1 PWR2
Input
Output
Input
Output
S5860-24XB-U
S5860-20SQ
Grounding Point Fan Slots Dual Power Supplies
STATUS/PWR1/PWR2
FAN/MGMT/ID SFP+ SFP28 QSFP+

LEDs Status Description
FAN
PWR1/PWR2
Solid Green The fan works properly.
Solid Red
1. A fan fault occurs.
2. The fan model does not match with the system.
3. Not all fans are in position.
STATUS
Solid Green The system works properly.
Solid Yellow
O
The temperature reaches the threshold value.
The power module is NOT in the position.
Solid Green
Solid Red
The power module works properly.
A power fault occurs.
MGMT
O The MGMT port is NOT connected.
Green The MGMT port is connected.
Blinking Green The MGMT port is transmitting or receiving data.
SFP+
O The SFP+ port is NOT connected.
Solid Green The SFP+ port is connected at 1/10G.
Blinking Green The SFP+ port is transmitting or receiving data at 1/10G.
SFP28
O The SFP28 port is NOT connected.
Solid Green The SFP28 port is connected at 10/25G.
Blinking Green The SFP28 port is transmitting or receiving data at 10/25G.
QSFP+
O The QSFP+ port is NOT connected.
Solid Green The QSFP+ port is connected at 10/40G.
Blinking Green The QSFP+ port is transmitting or receiving data at 10/40G.
O
ID
The locator is controlled by CPLD by default.
Solid Blue The locator is controlled by O&M personnel remotely.

Solid Green The system works properly.
Solid Yellow
1. The temperature reaches the warning threshold.
2.Only 3 fans are in the position.
3.One of the dual powers is not connected with the AC
power cord.
LEDs Status Description
O
Solid Red
The system is powered o.
Blinking Green Initialization is in progress.
1. One of the modules of the system fails.
2. There are less than3 fans.
3. The internal or partial temperature exceeds the
temperature limit,and the switching service resets.
STATUS
S5860-48SC
S5860-48SC
1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F 28F 29F 30F 31F 32F 33F 34F 35F 36F 37F 38F 39F 40F 41F 42F 43F 44F 45F 46F 47F 48F
100G
49F 50F 51F 52F 53F 54F 55F 56F
Status ID
SFP+ QSFP28
Status Status Status
Status
FUNC
ID
Link ACT
Status
PWR1
PWR2
1 2 3
4
MGMT
CONSOLE
AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB AFM-S48SC-FB
STATUS ID
STATUS
ID MGMT
MGMT
O The MGMT port is NOT connected.
Green The MGMT port is connected at 10/100/1000 Mbps.
Blinking Yellow The MGMT port is transmitting or receiving data.
O
ID
The locator is controlled by CPLD by default.
Solid Blue The locator is controlled by O&M personnel remotely.

LEDs Status Description
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=OverLoad
CONSOLE Yellow=100M
SFP+
O The SFP+ port is NOT connected.
Solid Green The SFP+ port is connected at 1/10G.
Blinking Green The SFP+ port is transmitting or receiving data at 1/10G.
QSFP28
O The QSFP28 port is NOT connected.
Solid Green The QSFP28 port isconnected at 40/100G.
Blinking Green The QSFP28 port is transmitting or receiving data at 40/100G.
Solid Green The system works properly.
Solid Yellow
Solid Blue
1. The temperature reaches the threshold value.
2. Dierent power modules are used together.
The locator takes eect. It is controlled by O&M personnel
remotely.
LEDs Status Description
O
Solid Red
The system is powered o.
Blinking Green Initialization is in progress.
1. A system fault occurs.
2. The temperature reaches the upper limit.
SYS
S5860-24XB-U
RJ45
PoE (1-24) SFP+
SFP28
MGMT
SYS
PWR FAN
PoE

Solid Green The power module works properly.
Solid Red
1. A power fault occurs.
2. No AC power cable is plugged in.
3. The power model does not match.
O The power module is NOT in the position.
Solid Yellow Indicates the PoE state.
O The MGMT port is NOT connected.
Solid Green The MGMT port is connected at 1000 Mbps.
Blinking Green The MGMT port is transmitting or receiving data at
1000 Mbps.
Solid Yellow The MGMT port is connected at 10/100 Mbps.
Blinking Yellow The MGMT port is transmitting or receiving data at
10/100 Mbps.
Solid Green
Solid Red
The fan works properly.
Solid Green Indicates the switching state.
1. A fan fault occurs.
2. The fan model does not match with the system.
3. Not all fans are in position.
PWR
FAN
PoE
MGMT
LEDs Status Description
O The RJ45 port is NOT connected.
Solid Green The RJ45 port is connected at 1/2.5/5/10G.
Blinking Green The RJ45 port is transmitting or receiving data at
1/2.5/5/10G.
Yellow The RJ45 port is connected at 100 Mbps.
Blinking Yellow The RJ45 port is transmitting or receiving data at 100 Mbps.
O PoE is o.
Solid Green PoE works properly.
Solid Yellow A PoE fault or overload occurs.
RJ45
PoE (1-24)

LEDs Status Description
SFP+
O The SFP+ port is NOT connected.
Solid Green The SFP+ port is connected at 1/10G.
Blinking Green The SFP+ port is transmitting or receiving data at 1/10G.
SFP28
O The SFP28 port is NOT connected.
Solid Green The SFP28 port is connected at 10/25G.
Blinking Green The SFP28 port is transmitting or receiving data at 10/25G.

Installation Requirements
Before you begin the installation, make sure that you have the followings:
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables, ber optical cables and console cable for connecting
network devices.
Site Environment：
Do not operate it in an area that exceeds an ambient temperature of 50°C.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
The installation site must be well ventilated. Ensure that there is adequate airow around the
switch.
The switch should be installed at least 1U (44.45mm) away from devices to its sides.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Ensure rack and working platforms are well earthed.

Mounting the Switch
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
1. Secure the mounting brackets to the two sides of the switch with supplied M4 screws.
Rack Mounting
1234
40GBreakout
25
26
40G

NOTE: Insert the power module steadily. Please pay attention to the direction of the
power panel to avoid wrong insertion. If the position is not proper, press the plug of the
power module and hold on to the module handle with one hand to pull it out slowly, then
re-insert it.
Installing the Power Supply Module
2. Attach the switch to the rack using four M6 screws and cage nuts.
1. Take a new power module out of the package and conrm the input mode and the input parameters
of the power module match the requirements.
2. Remove the old power module and take the plane printed with power information as the top panel
of the power module. Hold the handle of the power module with one hand, and hold the end of the
power module with the other hand. Insert it into the chassis along the guide rail uprightly and slowly
until it clicks into place, and make sure that it is in good contact with the power slot.
FAN2 PWR1
M1SFANI-F
Status
M1SFANI-F
Status

1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers and
screws.
Grounding the Switch
FAN1
M1SFANI-F
Status
M1SFANI-F
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Connecting the Power
FAN2 PWR1
M1SFANI-F
Status
M1SFANI-F
Status
WARNING: Do not install power cable while the power is on.
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.

MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
40G
FUNC
Connecting the RJ45 Ports
1. Connect an Ethernet cable to the RJ45 port of IP cameras, IP telephone, Access Points (AP), or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
1. Plug the compatible SFP/SFP+ transceiver into the SFP/SFP+ port.
2. Connect a ber optic cable to the ber transceiver. Then connect the other end of the cable to
another ber device.
Connecting the SFP/SFP+ Ports

S5860-20SQ
1. Plug the compatible SFP28 transceiver into the SFP28 port.
2. Connect a ber optic cable to the ber transceivers. Then connect the other end of the cable to
another ber device.
Connecting the SFP28 Ports
1. Plug the compatible QSFP+ transceiver into the QSFP+ port.
2. Connect a ber optic cable to the ber transceivers. Then connect the other end of the cable to
another ber device.
Connecting the QSFP+ Ports

MGMT
CONSOLE
STATUSPWR1 PWR2 FAN MGMT ID
21 43 65 87 109 1211 1413 1615 1817 19
FUNC
WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical bers without eye protection.
1. Plug the compatible QSFP28 transceiver into the QSFP28 port.
2. Connect a ber optic cable to the ber transceivers. Then connect the other end of the cable to
another ber device.
Connecting the QSFP28 Ports
S5860-48SC
1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F 13F 14F 15F 16F 17F 18F 19F 20F 21F 22F 23F 24F 25F 26F 27F 28F 29F 30F 31F 32F 33F 34F 35F 36F 37F 38F 39F 40F 41F 42F 43F 44F 45F 46F 47F 48F
100G
49F 50F 51F 52F 53F 54F 55F 56F
Status ID
1. Insert the RJ45 connector into the RJ45 console port on the switch.
2. Connect the DB9 female connector of the console cable to the serial port on the computer.
Connecting the Console Port

25G
123 4
22 2423 40G Breakout
25
26
S5860-20SQ
40G
MGMT
CONSOLE 25G
STATUSPWR1 PWR2 FAN MGMT ID
123 4
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 40G Breakout
25
26
40G
FUNC
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the MGMT port on the switch.
Connecting the MGMT Port
Stacking the Switches
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
MGMT
SYS PWR FAN PoE 1 2 3456 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PoE FUNC
S5860-24XB-U
Green=10G/5G/2.5G/1G On=Link Flashing=ACT PoE LED Mode:Green=Good Supply Yellow=Over Load
CONSOLE Yellow=100M
The S5860 series switches support stacking up to 2 switches between the same models together.
The switch can be physically stacked using optical ber cables connected to SFP+/SFP28 transceivers
or 10/25G Direct Attach Cables (DAC). Any two SFP+/SFP28 ports on the switch can be used for
physical stacking. The copper ports can also be used for physical stacking.
NOTE: S5860-20SQ/S5860-24XB-U switches support stacking with each other.

S5860-20SQ
Step 4: Click Login to display the web-based conguration page.
Conguring the Switch
Step 1: Connect the computer to the Management port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. (“x” is any number from 2 to 254.)
Conguring the Switch Using the Web-based Interface
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses:
Step 3: Open a browser, type http://192.168.1.1, and enter the default username and password,
admin/admin.
IE 8/9/10/11, Google Chrome, Firefox are supported
Login
admin
*****