Fuji Electric FRENIC-Mini (C2) User manual

• FWD, Rev, plus 3 Digital inputs configurable for Source or Sink.
• 0-10VDC analog inputs.
• 4-20mA analog input.
• Transistor outputs.
• Form C contact relay
o (250VAC 0.3A, cosØ=0.3), (48VDC, .5A).
• 24VDC max 200mA DC output power.
• 10VDC output for potentiometer.
• 24 VDC 50mA power source
Other Control Terminal
• RJ-45 keypad connection port.
FRENIC-Mini (C2) Quick Reference Guide
Min. Max.
Operang
Voltage
(Sink) Offlevel 22V 27V
Operang
Voltage
(Sink) Offlevel 0V 2V
Item
ON level 0V 2V
ON level 22V 27V
Max.
Operang ON level 2V
Voltage Offlevel 27V
50m A
Item
Maximum Current at on.
Orange = Outputs, Yellow = Analog Inputs, Blue = Digital Inputs
Control Card Terminals FRENIC-Mini (C2)Control Wiring
Note 1:
When connecting a DC REACTOR (DCR) (option), remove the jumper
bar from across the terminals [P1] and [P (+)].
For single-phase 100V input series, DCR shall be connected to the
point that is shown below.
Note 2:
Install a recommended molded-case circuit breaker (MCCB) or an earth leakage circuit breaker (ELCB) (with an
overcurrent protection function) in the primary circuit of the inverter to protect wiring. At this time, ensure that the
circuit breaker capacity is equivalent to or lower than the recommended capacity.
Note 3:
Install a magnetic contactor (MC) recommended for each inverter to separate the inverter form the power supply,
apart from the MCCB or ELCB, when necessary. Connect a surge suppressor in parallel when installing a coil such
as the MC or solenoid near the inverter.
Note 4:
(THR) is available when one of terminal functions for X1 to X3, FWD, REV (function code E01 to E03, E98 or E99)
is set to the data “9”.
Note 5:
Frequency can be set by connecting a frequency setting device (external potentiometer) among the terminals 11, 12
and 13 instead of inputting voltage signal (0 to +10V DC, 0 to +5V DC or +1 to +5V DC) between the terminals 12
and 11.
Note 6:
For the control signal wires, use shielded or twisted wires. Ground shielded wires. To prevent malfunction due to
noise, keep the control circuit wiring away from the main circuit wiring as far as possible (recommended:
10cm(3.94inches) or more), and never set them in the same wire duct. ⓔ
When crossing the control circuit wiring with the main circuit wiring, set them at right angles.
Note 7:
Three –phase 4wire cable is recommended for motor wiring to reduce the noise emitted. Connect the motor
grounding wire to the inverter grounding terminal G
Y1 Y1E FMA C1 PLC X1 X2 X3
11 12 13 11 CM FWD REV CM
〜
（ ）
（ ） （ ）
（）
（ １）
（ ）
（）
（ ）
（ ）
＋
−
（ ）
：
：
：
：
：
（ ）
（ ）
（ ）
（ ）
（）
（ ）
‐
（ ）
（ ）
（ ）

Dealers Industrial Equipment -- Visit https://DealersElectric.com or call [phone] for all of your electric motor & VFD needs!

Frenic-Mini (C2)Keypad
Quick Start Menus
Fuji Electric Corp. of America
47520 Westinghouse Drive, Fremont, CA 94539
Phone: [phone]
www.americas.fujielectric.com
1.F
Fundamental Funcons
1.E
Extension Terminal Funcons
1.C
Control Funcons ofFrequency
1.P
Motor 1 Parameters
1.H
High Performance Funcons
1.A
Motor 2 Funcons
1.J
Applicaon Funcons
1.Y
Link Funcons
To access Menes 2-7 change funcon code E52-2
2. rEP
3. oEP
4. I_O
5. CHE
6. AL
7. CPY
2.
rEP (Data Check)
Displays function codes that have
been changed from factory default.
5.
CHE (Maintenance Info)
5_00
Accumulated run time
5_01
DC link bus voltage
5_03
Max temperature of heat sink
5_04
Max effective current
5_05
Capacitance of the DC link bus
capacitance
5_06
Accumulated run time of
electrolyc capacitors on the PCB
5_07
Accumulated run time of cooling fan
5_08
Number of startups
5_09
Input wa-hour
1.F _ _
1.E _ _
1.C _ _
1.P _ _
1.H _ _
1.A _ _
1.J _ _
1.Y _ _
6.
AL (Alarm Info)
6_00
Output frequency
6_01
Output current
6_02
Output voltage
6_03
Calculated torque
6_04
Reference frequency
6_05
Rotational detection
6_06
Running status
6_07
Accumulated running time
6_08
Number of startups
6_09
DC link bus voltage
6_11
Max. temperature of heat sink
6_12
Terminal I/O status
6_13
Terminal input signal status in HEX
6_14
Terminal Output status in Hex
6_15
Number of consecutive occurrences
6_16
Overlapping alarm 1
3.
oPE (Operations Monitor)
3_00
Output frequency before slip
3_01
Output frequency after slip
3_02
Output Current
3_03
Output Voltage
3_05
Reference frequency
3_06
Rotation direcon
3_07
Running status
3_09
Load Shaft speed
3_10
PID SV
3_11
PID PV
4.
I_O (I/O Check)
4_00
I/O Signals on the
control card
4_01
I/O Signals on the
control card
4_02
Input Voltage on
terminal 12
4
_03
Input Current on
terminal C1
4_04
Output voltage of
Manual Frequency Command
Adjustment
Manual Run-Stop Command
Digital Display for Operation,
Function Codes & Fault Indication
Programming & Fault Reset
Digital Frequency Adjust
Function Code Data/Menu
Selection
FECA-MINIC2QRG
Dealers Industrial Equipment -- Visit https://DealersElectric.com or call [phone] for all of your electric motor & VFD needs!