FujiFilm instax SHARE SP-3 User manual

EN
DE
FR
ES
TW
KO
BOC703-200
User’s Guide/Trouble shooting/Safety precautions
Bedienungsanleitung/Fehlerbehebung/Sicherheitsmaßnahmen
Guide d’utilisation/Guide de dépannage/Précautions de sécurité
Manual de instrucciones/Solución de problemas/Precauciones de seguridad
使用說明書/現象、可能的原因及解決措施/安全注意事項
사용설명서/문제 해결/안전을 위한 주의사항
instax_BO-C_6lang.indb 1instax_BO-C_6lang.indb 1 2017/9/14 15:21:092017/9/14 15:21:09

ENGLISH:
See pages 3 to 29.
DEUTSCH:
Siehe Seiten 31 bis 57.
FRANÇAIS:
Voir pages 59 à 85.
ESPAÑOL:
Consulte las páginas 87 a 113.
中國語:
請參閱第 115 到141 頁。
한국어:
143~169페이지를 참조하십시오.
Independent JPEG Group (IJG) Licenses
This software is based in part on the work of the Independent JPEG Group.
© 2017 FUJIFILM Corporation. All rights reserved.
instax_BO-C_6lang.indb 2instax_BO-C_6lang.indb 2 2017/9/14 15:21:092017/9/14 15:21:09

3
EN
Parts Name..............................................4
Before Use................................................5
Inserting/Charging the Battery........5
Inserting the Battery....................................... 5
Charging the Battery...................................... 6
Charging Indicator .......................................... 6
Loading the instax SQUARE Film Pack ...7
Turning on/off the Printer..................8
Checking Remaining Battery Life............... 8
Connecting and Printing....................9
When establishing connection for the
first time:............................................................. 9
When connection is already established:....11
Reprinting............................................. 12
Deleting an Image............................. 13
Unloading a Used instax SQUARE
Film Pack ............................................... 13
About the LED Indication................ 14
SPECIFICATIONS ................................. 15
TROUBLE SHOOTING ........................ 16
IMPORTANT SAFETY NOTICE ......... 20
Handling the Battery ........................ 27
Contents
ENGLISH
• Read “IMPORTANT SAFETY NOTICE” (Page 20)
and “Handling the Battery” (Page 27) for safety
use.
• After reading this User’s Guide, keep it in a
safe, easy to find place where you can refer to
it if needed.
instax_BO-C_6lang.indb 3instax_BO-C_6lang.indb 3 2017/9/14 15:21:102017/9/14 15:21:10

4
EN
1Remaining battery LED 5USB connector cover 9Battery cover
2Remaining film LED 6USB connector 10 Back cover
3Print exit 7Back cover lock
4POWER button 8REPRINT button
Parts Name
8
31
9
7
10
4
5
6
2
instax_BO-C_6lang.indb 4instax_BO-C_6lang.indb 4 2017/9/14 15:21:102017/9/14 15:21:10

5
EN
Before Use
• Before using the printer, install the instax SHARE application on your device.
• When you are using an Android OS device, search for“instax SHARE”in the Google Play, then install the application.
* System requirements of an Android OS device: Android Ver 4.0.3 or later and Google Play are installed.
• When you are using an iOS device, search for“instax SHARE” in the App Store, then install the application.
* System requirements of an iOS device: iOS Ver 8.0 or later is installed.
You may not be able to print from some devices even if you have installed the instax SHARE application and your
device meets the requirements listed here.
• The battery is not fully charged at shipment. Be sure to charge it before using the printer.
Access instax SHARE website for the latest information on system requirements.
Inserting/Charging the Battery
Inserting the Battery
Pull down the battery cover lock
to open the battery cover.
Insert the battery according to the arrow on
it. Make sure the yellow line on the battery
aligns with the mark on the printer.
Align the tabs on the battery cover
and push the battery cover lock
until it clicks into place.
~Ÿ !
instax_BO-C_6lang.indb 5instax_BO-C_6lang.indb 5 2017/9/14 15:21:102017/9/14 15:21:10

6
EN
Inserting/Charging the Battery (Continued)
Charging the Battery Charging Indicator
Indication Battery status/Action
Lights red (ON)
Flashes red (OFF) Charging is in progress.
Lights orange (ON)
Flashes orange (OFF) Charging is half complete.
Lights green (ON)
Flashes green (OFF) Charging is almost complete.
Flashes green, then
goes off (OFF) Charging is complete.
Flashes green and
red alternately, or
flashes red, then
goes off
An error has occurred. Stop
charging.
Charging from a PC:
• Connect the printer and PC directly. Do not connect
them via a keyboard or USB hub.
• If the PC enters sleep mode while charging is in
progress, charging will stop. If you continue charging,
resume the PC and reconnect the USB cable.
• You may not charge the printer from a PC depending
on your PC specifications, settings, or status.
Connect the printer and an AC power adapter supplied
with your smartphone using the supplied USB cable, then
connect the AC power adapter to an indoor power outlet.
The remaining battery LED indicates the battery charge
status. For details, see the table on the right column.
• Use an AC adapter to meet the rated output below:
DC 5.0 V/1000 mA
• You can print an image while charging is in progress.
• Charging time is approximately three hours.
Be careful of the orientation. Connect the USB cable
with the mark ( ) on the terminal facing up.
instax_BO-C_6lang.indb 6instax_BO-C_6lang.indb 6 2017/9/14 15:21:102017/9/14 15:21:10

7
EN
Loading the instax SQUARE Film Pack
~Ÿ
Caution
Do not open the back cover until you have used up all the film; otherwise, the rest of the film will
become exposed and turn white.The film can no longer be used.
• When you load the film pack, never press the two rectangular holes on the back of the film pack.
• Never use a film pack beyond its shelf life; otherwise, it may damage the printer.
Use FUJIFILM Instant Film “instax SQUARE”only. The instax mini film or instax WIDE film cannot be used.
Notes on the film pack
• Each FUJIFILM Instant Film“instax SQUARE” pack contains 1 black film protective cover and 10 film sheets.
• Do not remove the film pack from its inner bag before loading it into the printer.
• The film cover is ejected automatically when the back cover is closed.
For details, refer to the instructions and warnings on FUJIFILM Instant Film "instax SQUARE".
Continued on the next page
Pull the back cover lock down to open the back
cover.
Hold both sides of the film pack, align the bottom of the
film pack on the groove of the film chamber (1), then insert
it straight (2).
2
1
instax_BO-C_6lang.indb 7instax_BO-C_6lang.indb 7 2017/9/14 15:21:102017/9/14 15:21:10

8
EN
Loading the instax SQUARE Film Pack
(Contunued)
⁄
!
Close the back cover.
Make sure the back
cover lock clicks into
place.
The film cover (black) is ejected
automatically when the back
cover is closed. Remove the film
cover from the print exit.
Turning on/off the Printer
Press and hold the POWER button for approx. 1 second
to turn the printer on or off.
Turning on the printer lights up the remaining battery
LED.
If no operation occurs for a certain period of time, the
printer turns off automatically.
Checking Remaining Battery Life
Use the remaining battery LED to check when turning
the printer on or while printing is in progress.
Indication Remaining battery life
Green Sufficient
Orange At half capacity
Red Low. Charging the battery is
recommended. (See page 6.)
Printer turns off
after flashing red.
No battery capacity remains.
Charge the battery. (See page 6.)
instax_BO-C_6lang.indb 8instax_BO-C_6lang.indb 8 2017/9/14 15:21:102017/9/14 15:21:10

9
EN
Connecting and Printing
~
Ÿ
!
Continued on the next page
Wireless LAN Setup for iOS Devices
When you are using an iOS device, follow the procedure
below to perform wireless LAN setup.
1. Select “ON” for “Wi-Fi” in the “Settings” menu of your device.
2. Tap the network name (printer name) under “Choose a Network” .
When establishing connection for
the first time:
Press and hold the POWER button for approx.
1 second to turn the printer on.
The remaining battery LED lights up.
Start the downloaded application “instax SHARE”.
Select the picture to print or take a picture.
Notes on Printing
1. Place the printer vertically.
2. When printing, put the printer on a steady surface
such as a desk.
instax_BO-C_6lang.indb 9instax_BO-C_6lang.indb 9 2017/9/14 15:21:112017/9/14 15:21:11

10
EN
⁄
Connecting and Printing (Continued)
@
Tap“Connect and print”.
When a printer is detected,
tap“Connect”. If multiple
printers are detected, select
the printer to connect from
the list.
Printer's identifier (SSID) is
located on the bottom of the
printer.
#
Enter the factory default
password (1111) or the one you
specified, then tap“OK”.
The printer starts printing.
To reset the password to the factory default
(1111), turn the printer on while holding the
REPRINT button.
When the film has been ejected (the
printer stops making a sound), grasp
the edge of the film, then take it out.
1 remaining film LED turns off every
time you print an image.
¤
Before tapping“Connect
and print”, tapping on
the lower right displays the
edit menu. You can add
a template or adjust an
image on this menu.
Tap“Done”to exit from the
menu.
When printing, put the
printer on a steady surface
such as a desk.
㻵㻺㻿㼀㻭㼄㻙㻝㻝㻝㻝
㻝㻝㻝㻝
instax_BO-C_6lang.indb 10instax_BO-C_6lang.indb 10 2017/9/14 15:21:112017/9/14 15:21:11