Fujitsu MB2198-590-E User manual

The following document contains information on Cypress products.

FUJITSU SEMICONDUCTOR
SUPPORT SYSTEM SS01-71076-1E
DSU-FR EMULATOR
F
2
MC-16FX EXPANSION TRACE BOARD
MB2198-590-E
OPERATION MANUAL

i
PREFACE
Thank you for purchasing the DSU-FR*1emulator F2MC*2-16FX expansion trace board (model number:
MB2198-590-E)*3.
This product is used to connect a Fujitsu F2MC-16FX family microcontroller MB96V300 (BGA-416P)
to a DSU-FR emulator (model number: MB2198-01)*4and DSU-FR emulator F2MC-16FX BGA-416P
adapter (model number: MB2198-500)*5.
This document describes how to handle the DSU-FR emulator F2MC-16FX expansion trace board.
Be sure to read this document before using the product.
For details on the mass production MCUs and evaluation MCUs supported by this product, consult with
sales or support representative.
*1 : FR, the abbreviation of FUJITSU RISC controller, is a line of products of FUJITSU Limited.
*2 : F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
*3 : Referred to as the trace board in this manual.
*4 : Referred to as the emulator in this manual.
*5 : Referred to as the adapter in this manual.
■Safe use of this Product
This manual contains important information regarding how to use this product safely. Be sure to read this
manual before using the adapter, and to follow the directions given in this manual in order to use the
product correctly.
In particular, thoroughly read the "Safety Precautions" at the start of this manual and perform a full safety
check before using this product.
After reading the manual, keep it handy for future reference.
■Warranties and Liability
The specifications of the adapter are subject to change without notice.
Note that Fujitsu shall accept no responsibility for any consequences arising either directly or indirectly
from the use of this product.
■Product Operating Environment
Use the product at an operating temperature of between 5 °C and 35 °C and at an operating humidity of
between 20% to 80%. Use the product in an environment that is free of condensation and avoid high tem-
perature or humidity.
This product consists of a printed circuit board unit without casing with all electronic components ex-
posed.
Accordingly, do not place other objects on top of the circuit board and do not allow the metal parts of the
unit to come into contact with people or materials that may include static electricity. Similarly, keep any
objects that are flammable, likely to cause a short circuit, or cause any other such problem well away
from the unit when the power to the unit is turned on.
Use the product as horizontal as possible and avoid operating it at a place exposed to strong vibration,
dust, or explosive gas.
If the unit is used in an environment that does not satisfy the above guidelines, there is a risk of unex-
pected damage to property or injury to the user or other people in the vicinity.
You should also keep the packaging materials used for shipping the product. These are useful if the prod-
uct needs to be re-shipped again, for example, if it becomes faulty and needs to be repaired.
■Related Manuals
Refer to the following manuals in conjunction with this manual.
•DSU-FR EMULATOR MB2198-01 HARDWARE MANUAL
•DSU-FR EMULATOR BGA-416P ADAPTER MB2198-500 OPERATION MANUAL
•DSU-FR EMULATOR QFP-100P HEADER TYPE3 MB2198-501 OPERATION MANUAL

ii
■European RoHS compliance
Products with a -E suffix on the part number are European RoHS compliant products.
■Notice on this document
All information included in this document is current as of the date it is issued. Such information is subject
to change without any prior notice.
Please confirm the latest relevant information with the sales representatives.

iii
■Cautions of the Products Described in this Document
The following precautions apply to the products described in this manual.
Warning Indicates a potentially hazardous situation which could result in death or serious injury
and/or a fault in the user’s system if not avoided appropriately.
Electricshock,
Damage
Before performing any operation described in this manual, turn off all the power sup-
plies to the system. Performing such an operation with the power on may cause an
electric shock or device fault.
Electricshock,
Damage
Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.
Caution
Indicates the presence of a hazard that may cause a minor or moderate injury, damages
to this product or devices connected to it, or may cause to loose software resources and
other properties such as data, if the device is not used appropriately.
Cuts, Damage
Before moving the product, be sure to turn off all the power supplies and remove it from
the adapters. Watch your step when carrying the product. Do not use the product in an
unstable location such as a place exposed to strong vibration or a sloping surface.
Doing so may cause the product to fall, resulting in an injury or fault.
Cuts This product has sharp edges that are left unavoidably exposed.
Take care when handling the product to avoid being injured by these sharp edges.
Damage Do not place anything on the product or expose the product to physical shocks. Do not
carry the product after the power has been turned on. Doing so may cause a malfunc-
tion due to overloading or shock.
Damage
Since the product contains many electronic components, keep it away from direct sun-
light, high temperature, and high humidity to prevent condensation. Do not use or store
the product where it is exposed to much dust or a strong magnetic or electric
field for an extended period of time. Inappropriate operating or storage environments
may cause a fault.
Damage Use the product within the ranges given in the specifications.
Operation over the specified ranges may cause a fault.
Damage To prevent electrostatic breakdown, do not let your finger or other object come into con-
tact with the metal parts of any of the connectors. Before handling the product, touch a
metal object (such as a door knob) to discharge any static electricity from your body.
Damage
When turning the power on or off, follow the relevant procedure as described in this
document. Before turning the power on, in particular, be sure to finish making all the
required connections. Furthermore, be sure to configure and use the product by follow-
ing the instructions given in this document. Using the product incorrectly or inappropri-
ately may cause a fault.
Damage Because the product has no casing, it is recommended that it be stored in the original
packaging. Transporting the product may cause a damage or fault. Therefore, keep the
packaging materials and use them when re-shipping the product.

iv
Copyright © 2008 FUJITSU LIMITED All rights reserved
•The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
•The information, such as descriptions of function and application circuit examples, in this document are presented solely
for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU does
not warrant proper operation of the device with respect to use based on such information. When you develop equipment
incorporating the device based on such information, you must assume any responsibility arising out of such use of the in-
formation. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the information.
•Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as
license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of
FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party's intellectual property right or
other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual property rights
or other rights of third parties which would result from the use of information contained herein.
•The products described in this document are designed, developed and manufactured as contemplated for general use, in-
cluding without limitation, ordinary industrial use, general office use, personal use, and household use, but are not de-
signed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless
extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury,
severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic con-
trol, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in con-
nection with above-mentioned uses of the products.
•Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such
failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and
prevention of over-current levels and other abnormal operating conditions.
•Exportation/release of any products described in this document may require necessary procedures in accordance with the
regulations of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
•The company names and brand names herein are the trademarks or registered trademarks of their respective owners.

1
1. Product Overview
■Overview
This product is an external trace board that provides a maximum capacity of 2 Gbytes (64 bits ×256 Mframe)
of external trace functionality. The trace board is used by connecting to the F2MC-16FX BGA-416P adapter
(model number: MB2198-500) ,which connects the DSU-FR Emulator (model number: MB2198-01, re-
ferred to as the emulator in this manual) to a user system using a Fujitsu F2MC-16FX family microcontroller.
This product is an optional product for the DSU-FR emulator that assists the development of user systems
that use a Fujitsu F2MC-16FX family microcontroller.
■Verifying the Contents of the Package
Check that all of the following components are present in the package before using the trace board.
•Trace board :1
•AC adapter :1
•Locking screws :1 set (2 screws)
•Operation manual (English: this manual) :1
•Operation manual (Japanese) :1
■Related Products
The optional products shown in Table 1 are available for the adapter. Purchase these separately as need-
ed.
Table 1 Optional Parts
* : The evaluation MCU is used connected to the adapter.
Consult with sales or support representative for details on compatible evaluation MCUs.
Name Part number
DSU-FR emulator MB2198-01
F2MC-16FX BGA-416P adapter MB2198-500
F2MC-16FX QFP-100P header type3 MB2198-501
Evaluation MCU* MB96V300

2
■System Configuration
The trace board is used in combination with the emulator, adapter, header board, and other components.
These are used connected to the user system.
A schematic of the system configuration of this product is shown in Figure 1.
Figure 1 System configuration schematic
A host computer and emulator debugger software need to be purchased separately to use the emulator.
See "3. Connection" for details on how to connect the adapter and the header board.
See the hardware manual and operation manual of the emulator and adapter for the specifications of these
components.
Host computer
External trigger/Program execution
General-purpose
measurement device
AC adapter
Flat cable
Adapter
Evaluation
MCU
(MB96V300)
Adapter board
Header board
User system
Header
DSU-FR emulator
RS232C, USB, LAN
AC Adapter
for the Emulator
AC adapter
AC adapter
for the trace board
(Supplied with this product)
Trace board
Trace board
(this product)
AC in
AC in

3
■External Appearance and Component Names
The external appearance of the adapter board is shown in Figure 2 and the component names are shown
in Figure 3.
Figure 2 External appearance (component side)
RN18
GND
ADAPTER BOARD
POWER ON
D4
160
159
INITDONE
RN2 RN1
M1
R13
R50
R60
R70
R79
AB
R14
R8 R9
R6 R7
R2 R3
R103R109
R106 R105
R117 R108
R112 R115
R116 R110
R113
C4
CRCERR
RN10
R114
R51
R49
R68
R77
X1
R157
A
1
RN9
RN12
MSEL0
MSEL1
RN11
R154
RN8 RN7
CN1
ADAPTER-BOARD CN
2
1
D5
AC ADAPTER
POWER ON
R162
D2
L1
L2
M8
Q1
L3
FL1
C32
+1.2 V
C33
C35
RN20
GND
R171
RN13
+5.0 V
RN14
+3.3V
M9
85
14
RN15
R161
R163
R164
R166
R168
RN19 GND C27
10
M7
M6 M5 M4
C29
R173
C36
R172
R174
R175
M10
85
14
R177
C38
R176
R178
R179
M11
85
14
R181
C40
R180
R182
R183
M12
85
14
R185 C42
R184
R186
R187
5 4
5 41D1
D3
8
1
RN6 RN4
RN5 RN3
T0 T2
22
T1 T3
2
S1
10
R496
C130 C128
M41
C127 C126 C129
R497
R498
R499
R500
R501
R502
R503
R520
M40
R521
R522
R523
R524
R525
R526
R527 C106 C105 C125
R436
M33
R437
R438
R439
R440
R441
R442
R443C103C102 C104
R456
M32
R457
R458
R459
R460
R461
R462
R463C82 C81 C104
R374
M25
R375
R368
R369
R372
R373
R370
R371 C79 C78 C80
R392
M24
R393
R394
R395
R396
R397
R398
R399 C58 C57 C77
R335
M17
R336
R337
R338
R339
R340
R341
R342 C55 C54 C56
C53
R285
M16
R286
R279
R280
R281
R282
R283
R284
R480
C118 C116
M37
RN16
GND
C137C139 C117
R481
R482
R483
R484
R485
R486
R487
R536
M44
R537
R538
R539
R540
R541
R542
R543C93C92 C138
R416
M29
R417
R418
R419
R421
R423
R426
R427 C115 C113C94
R472
M36
R473
R474
R475
R476
R477
R478
R479 C69 C68 C114
R352
M25
R353
R354
R355
R358
R359
R356
R357 C91 C89 C70
R408
M28
R410
R409
R412
R413
R411
R415
R414 C46 C45 C90
R263
M13
R264
R265
R266
R267
R268
R269
R270 C65 C67 C44
C66
R301
M20
GND
RN17
R302
R295
R296
R297
R298
R299
R300
19
R160
R159
1 85
R52
R63 R65 R67 R69
R44 R54 R55 R57 R56
R58 R59
R61
R51
R93 R73 R71 R38 R39
4
M2
R158
1R150
R153
R111R126R128
R126R128 R131R133 R127R129 R130R132 R125R123 R120R118 R124R122 R121R119
8M3
5
4
No. Description Function
(1) Trace board fixing bracket A bracket for connecting the trace board to the adapter.
(2) Expansion trace connector
A connector that connects to the adapter.
The power supply to the trace board is supplied via this connector from
the AC adapter connected to the adapter board.
(3) Adapter power LED Lights up when the adapter power is on.
(4) Trace board power LED
Lights up when then trace board power is on.
The power to the trace board is turned on by connecting the supplied AC
adapter. There is no power switch.
(3)
(2)
(4)
(1)

4
Figure 3 External appearance(solder side)
C124
M39
C133 C122 C123
R495
R494
R493
R491
R490
R489
R488
R492
M42
C100 C131C132
R535
R524
R533
R531
R530
R529
R528
R532
M31
C109 C98 C99
R435
R434
R433
R431
R430
R429
R428
R432
M34
C76 C107 C108
R471
R470
R469
R467
R466
R465
R464
R468
M23
C85 C74 C75
R363
R362
R365
R361
R360
R367
R366
R364
M26
C52 C83C84
R406
R407
R404
R403
R402
R401
R400
R405
M15
C59 C50 C51
R334
R333
R332
R330
R329
R328
R327
R331
M18
C60 C61
R291
R292
R289
R287
R288
R293
R294
R290
RB2 RB7
RB8
RB1
C136
M43
C121 C134C135
R511
R510
R509
R507
R506
R505
R504
R508
M38
C112 C119 C120
R519
R518
R517
R515
R514
R513
R512
R516
M35
C97 C110 C111
R451
R450
R449
R447
R446
R445
R444
R448
M30
C88 C95 C96
R455
R454
R453
R425
R424
R422
R420
R452
M27
C73C86 C87
R383
R382
R381
R379
R378
R377
R376
R380
M22
C64 C71 C72
R391
R390
R389
R387
R386
R385
R384
R388
M19
C49 C62 C63
R350
R349
R348
R346
R345
R344
R343
R347
M14
C47 C48
R278
R277
R276
R274
R273
R272
R271
R275
RB4
C43C41 C39C37
C25
C26
R170
R142 R147 R144 R149 R136 R141 R140 R92 R90
R91 R89
C20
C1
R137
R143 R146 R145 R148
R134
R139
R138
R135
C24C21
C23
C28
R167
RB5
RB6
RB3
R165
C31
C30
R252
C15
C11
C6
R76 R37 R80 R78 R30 R27 R33 R26 R28
R42
R23 R36
R83 R82 R84 R24 R34 R41 R29 R32 R25
R31
R22
R21
R35
R40
R152
C2
C16
C8
C7
R169
C34
R99
R94
R85
R87
R104
R100
R97
R101
R96
R86
R88
R107
R102
R98
R95
R156
R155
C13
C14
R19
R17
R45
R46
R12
R4
R53
R48
R11
R62
R72
R75
R81 C12
C9
C19
R10
R1
R5
R43
R57
R66
R64
R74
C5
C10
C18
R18
R20
R16
R15
C3
C17
R253
R254