Fulleon ASSERTA User manual

(Optional extra)
Mounting bracket.
Fix base to wall in 4 positions.
2. Fixing Details
25-5644 Iss A
Knockout or drill required cable gland holes, and fix required
1. Installation
Dimensions
Industrial Sounder/Beacon (230Vac)
Specification
5. Sounder Assembly
4. Sounder Settings
155mm
212mm
168mm
ASSERTA
2
4
3
1
Switch 1 bit 4 is to select voice (0)/ no voice (1). (Where fitted)
Minutes
(Stage 3 Tone is dependent on the setting of switch 2)
Turn dial clockwise to increase volume.
010X10110X
6
6
4. Switch 3 (Stage 2 tone selection)
3. Switch 2 (Stage1 tone selection)
OPEN
321 54
0 = Open
1 = Closed
OPEN
12345
See table overleaf.
See table overleaf.
101X
100X 20
15 001X
000X
2. Switch 1 (Time out setting)
(Nominal 20dB range)
1. Volume Control
OPEN
321 4 MinutesBIT 123X
111X 5011X
BIT 123X
30
40
∞
25
0°
90°
cable glands.
148mm
117
N
COM
L
Stage 3
Stage 1
Stage 2
N
L
N
L
L
N
Ensure that guide
ribs are aligned.
(Top & Bottom)
WARNING : On some tones the output level can exceed 120dB(A) @ 1m.
: Consult the relevant or appropriate health and safety regulations for guidelines.
Tones Table overleaf.
: Do not remove cover, refer servicing to qualified personnel.
: High voltage present within this equipment.
NOTE : Polar dispersion information available in the technical manual. (Ref:M03-003)
Ingress Protection
Termination
Specification
Current Consumption
Operating Temperature
Operation
Operating Voltage Range
Sound Output @ 1m
Construction
Tones
230Vac 110dB(A)
Continuous
230Vac 50/60Hz
0.28~2.5mm² cable
ABS /PC FR plastic
-25°C to +75°C
See table overleaf
39mA@230Vac
42 see table overleaf
IP66
230Vac 50/60Hz
42 see table overleaf
65mA@230Vac
See table overleaf
-25°C to +75°C
ABS /PC FR plastic
0.28~2.5mm² cable
IP66
Continuous
230Vac 120dB(A)
1. Plug the 5 way ribbon cable into the base header.
2. Plug the 2 way ribbon cable into the base header.
3. Ensure that the top indicator on the base is aligned with the top indicator on
the sounder, and push the sounder onto the base.
4. Secure the sounder to the base using the bolts provided.
230Vac 50/60HzOperating Voltage Range
Ingress Protection
Termination
Construction
Operating Temperature
Current Consumption
0.28~2.5mm² cable
IP66
15mA
-25°C to +75°C
ABS /PC FR plastic
Beacon 230Vac
Sounder
NOTE: Ensure that the IP integrity
is maintained during gland
fitting.Take care not to disturb the
electronics while drilling.Remove
PCB if required)
3. Connection
NOTE: A readily accessible
disconnect device must be
incorporated in the mains
supply wiring to this unit.
}
}
Beacon
Sounder
Fuse 80mA Antisurge, 20mm
Ensure that the mains switch is set to 230V.
Fuse 80mA Antisurge, 20mm 80mA Antisurge, 20mm
Rating 2 Joules
Hole positions for additional cable entries.
Knock outs for cable entries.
(Top & Bottom)

118110 A14
Sweep 3.75s followed by 0.25s gap pulsed @ 0.625s 1Hz (500ms-500ms) 3X500ms pulses followed by 1.5s silence then repeat Sweep for 0.85s, 1s delay, repeat 0.7s On, 0.3 Off Sweep up & down over 3s Sweep up 1s, sweep down 0.5s
Continuous
Sweep Sweep
Intermittent
Alternating
Continuous
Intermittent
Sweep
Continuous Continuous
Sweep Sweep011011A37
A38 A39 A41 A42 A40
010111 010110 011010 011001 011000
A32 A31 A34 A36 A35 A33
011110 011101 011100 100001 100000 011111
1400 to 1600
422 to 775
500 to 1200
470 370 720
Steady Steady
500 to 1200
1000 & 2000
300 to 1200
420 Bell Bell
Steady 1Hz
NF C 48-265 German ind alarm Horn (USA) Air Horn (USA) NFPA Whoop Siren See attached for waveform details Bell/US Temporal Singapore Australian alert Australian evac
A14 A14 A14
A4 A3
A14
A3 A3
A14 A14 A14
111 111 107 108 109 108 109 109 104 104 110
114 113 118 118 117 115 117 116 118 117 117
2850Continuous Steady111100A4
3s sweep, 0.5s silence, then repeat (rep) 0.28Hz (1.8s On/1.8s Off) 0.05Hz (6.5s On/13s Off) 1HZ (500ms-500ms) 0.5Hz (1s On/1s Off) 3.3Hz (150ms On/150ms Off) 0.8Hz (250ms On/1s Off) 0.5Hz (1s On/1s Off) 1Hz (500ms-500ms) 0.5Hz (1s On/1s Off) 2Hz (250ms-250ms) 2Hz (250ms-250ms) 4Hz (150ms On/100ms Off) 2Hz (250ms-250ms)(Squashni Micro tones) 2Hz (250ms-250ms)(Symphoni tones) 3X500ms pulses followed by 1.5s silence then repeat 3X500ms pulses followed by 1.5s silence then repeat
660IntermittentA17 101111
Intermittent Intermittent
Alternating
Continuous
Intermittent
Sweep Sweep
Alternating Alternating
Continuous
Intermittent
Alternating
Intermittent
A24 101000 A25 A27 A29 A28 A26 A30
100101 100100 100011 100010 100111 100110
A18 A19 A20 A21 A23 A22
101011 101001 101010 101110 101101 101100
2400 to 2850 50Hz
800 & 970 990 & 650
510 &610
4000 2850
970
Steady
554 & 440
800 to 970
2850
660 660 660
50Hz Steady
Sweep
Slow Whoop
Sweep
Intermittent
Alternating
Continuous
Intermittent Intermittent
Alternating
Intermittent
Alternating
Sweep
A12 A14 A13 A11 A16 A15
110010 110000 110001 110011 110100 110101
A10
A7 A9 A8 A6 A5
111001 110110 110111 111000 111010 111011
800 & 970 554 & 440
970 660
2850
970
Steady 100ms-400ms
2400 to 2850
500 to 1200
2400 to 2850
2400 & 2850
1200 to 500
970
1Hz 1Hz 7Hz
Swedish (Local warning) ISO 8201/US Temporal ISO 8201/US Temporal Swedish (Pre-mess) Swedish (All clear) Swedish (Turn out) Swedish France NFS 32 S 32-001 PFEER - Toxic gas Swedish (Air raid) Slow Whoop Netherlands DIN/PFEER (PAPA) PFEER alert
2Hz (250ms-250ms)
Industrial Sounder Tones Table
Description
Alternating
Sweep Sweep
No
A2 A3 A1
111101 111110 111111
123456
CODE
Frequencies
800 & 970 800 & 970 800 & 970
1Hz (1/s) 7Hz (7/s) Pattern
TONE
Use
111106 A9
A4
A14
A4
A14 A14 A14 A14
A4 A6 A4
A14
A4
A14
A4
A19
A1
A14 A14 A14
A8
A14
A4
A14 A14
A4
A14
115106
106 107 106 106 105 109 106 109 107 101 109 109 107
110 105 117 116 118 112 118 110 117 115 116 115 115
103 105 111 111 108 108 109 107 108 109 106 106
118 114 115 112 117 118 119 113 117 119 110 109
A14 A14 A14
STAGE 3
dB(A)@1m
115Vac/230Vac LP
111 112 112
115Vac/230Vac HP
dB(A)@1m
Stage 1 & 2
120 120 120