Furniture Solutions VEGA 18VEGBSX2.AB User manual

Page 1 of 6
VEGA BARSTOOL
Made in China
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St, Revesby, NSW. 2212
Your furniture purchase is an investment.
Here are a few tips to maximize the lifetime of your furniture with a minimum,
amount of effort.
Properly caring for your furniture can help ensure that it looks great year after year.
Wood Furniture Maintenance:
Note no added polishing is required.
Always dust, wipe, and clean with the grain of the wood.
Dust with a soft clean cloth.
Dust will scratch the furniture surface if not removed properly!
If a polished surface becomes foggy.
Rub it with a cloth dipped in a solution of one tablespoon
vinegar to one liter of water. Rub softly with the grain until the
surface is completely dry.
Soap and water are not advisable for wood surface.
Water can penetrate the finish and raise the grain on wood,
causing damage.
Remember to change dusting cloths frequently as dirty cloths
may scratch your furniture's surface.
Iron Work Maintenance:
Keep dust free; Bolts and screws must be checked and
re-tightened as necessary or minimum very 6 months.
Paint chips should be touched up as they occur. When bare
metal is exposed to environment, metal will first oxidize and next
stage will be rust, causing structural integrity to be
compromised.
The Enemies of Wood:
Moisture is wood's worst enemy.
Liquid spills should be gently wipe up immediately.
Coasters should be used under all beverages.
Do not allow rubber or vinyl materials to lie on the furniture.
Chemicals in rubber may leave a stain.
Put a strip of felt or leather under accessories that have
rubber or vinyl.
Heat creates a chemical change in the furniture's finish,
which result in a white spot. Use protective pads under hot
dishes, appliances, etc.
Sunlight's ultraviolet rays can damage the finish of
furniture.
Do not place furniture directly against a heater or radiator
and do not place in the path of hot streams of air from
central heating. This will cause extreme localized drying of
the wood.
The Enemies Iron Work:
All iron or steel products are painted to protect metal from
the elements.
Do not immerse in water. Liquid spills should cleaned off
immediately. Alcohol, fruit juice etc are acidic and can
cause paint finish to change colour. When cleaning please
use only Ph neutral products.
Item# 18VEGBSX2.AB
Height: 762mm
Seat: 406mm Round
Stain: Aged Barley

PRE-ASSEMBLY PREPARATION
Avoid use of powered/battery drills.
Improper use of drills can irreversible damage fittings.
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Ensure to check all components for any damage before assembly. Please report any
damage found to below, if possible forward images of component to below
5. Always read the assembly instructions carefully before beginning assembly.
6. Keep all hardware parts and packaging out of reach of small children.
7. Do not over tighten the screws and bolts as this may damage the threads
2
10
MINUTES
ALLOW TIME PEOPLE REQUIRED
X1
For any assistance with assembly or for missing parts
Please contact:
Place of purchase or Furniture Solutions.
Customer Service (Australia) Phone-1300 794 188
Email- [email protected]
Page 2 of 6

Vega Barstool Hardware and Component List
12PCS
12PCS
Spring Washer
6mm
Flat Washer
6mm x 13mm
Bolt
6mm x 16mm
12PCS
Page 3 of 6
Hardware List:Item #PVG420BS-AH
Componet List
Seat Frame
PVG420CSSF
Swivel Plate
PVG420CSSP
Leg
PVG420CSL
Plastic Plug
PVG420CSPP
Ring
PVG420CSR
Seat Bottom Frame
PVG420CSSBF
Please note factory have pre-assembled seat frame, swivel plate and seat bottom frame.
Factory has also pre-fitted the plastic plug in base of leg.
Tool 4mm

Assembly Instructions
C
A
B
C
A
B
C
A
B
Page 4 of 6
Prepare as instructed on page 2: Follow steps do not move ahead
Step 1: Fit 3 legs to base of seat as shown below,
note leg has a threaded hole inside of tube, this faces
into the middle of stool seat.
Take bolt (C) add spring washer (A) also add flat
washer (B). Ensure to place washers in correct order.
Insert bolt with washer into base of leg and into
thread in base of seat, bolt needs be seated properly
by hand turn bolt 2-3 times, test it has gripped by
gently pulling back on bolt.
Please fit second bolt in same manner.
Then hand tighten both bolts until they feel firm.
Repeat for the other two legs
Move to Step#2
Step 2: Fit Ring as indicated in diagram, ensure the
tongue with hole is facing up the leg.
Take bolt (C) add spring washer (A) also add flat
washer (B). Ensure to place washers in correct order.
Insert bolt with washer into base of leg and into
thread in base of seat, bolt needs be seated properly
by hand turn bolt 2-3 times, test it has gripped by
gently pulling back on bolt.
Please fit other two (2) bolts in same manner.
Then hand tighten both bolts until they feel firm.
Move to Step#3

C
A
B
BAC
C
A
B
Assembly Instructions
Step 3: Fit last Leg as indicated in diagram. Please
follow same method as previously shown. remember
to only do bolts up finger tight.
Once you have fitted by hand all bolts, you need to
ensure that the stool when finished is square/level.
Suggest you turn stool over gently onto it's feet,
ensure surface is level.
Then by eye line up ring and base of seat so they are
square with each other, then take tool (D) and start
to tighten bolts that go into ring.
Once all bolts are tight gently turn stool back over
and proceed to tighten all other bolts.
Assembly now complete
Move to Step#4
Step 4: Once assembly complete, Turn barstool over
on it's feet. Take a seat and test swivel action.
Trouble shooting.
If you find barstool is not level please check list below
•Ensure area is level. Test by moving stool to a
different location and or turn stool around.
•Ensure all legs have plastic plug fitted. If missing
contact your reseller or Furniture Solution direct
•Possible cause could be incorrect assembly.
Please take tool provided and loosen bolts in
ring section, put some weight on top of stool
and again by eye check level, then re-tighten
bolts.
Test again the first two (2) suggestion. should
now be level.
If level problem still remains please contact your reseller or Furniture Solution Direct.
Please ensure that you follow above trouble shooting list before contacting reseller or Furniture Solution as
incorrect assembly is not covered under warranty and fees may be applied.
Page 5 of 6

WARRANTY DETAIL
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation,
chipping/scratching, exposure to extreme heat/cold, mould/mildew, hardware corrosion,
misuse of the products & defects caused by failure in duty of care for the product in
accordance with the care instructions. Warranty only extends to original purchaser and is
not transferable, except when given as a gift.
Notice:
While every effort is made to use quality materials our products are limited in design for
domestic use only & are not suitable for commercial use.
Care should be taken not to place product near heat sources.
Duty of care:
While every attempt is made to supply product using quality components there is always a
need from consumer to help ensure long life of use for product.
Instruction manuals are designed with the nature of materials used in construction of the
product.
*Proper use of item only what it is designed to do
*Regular maintenance and cleaning
In areas of high content of salt air, pollution & moisture require more frequent cleaning.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required
before proceeding with any claim. In the case of product defects providing photos may be
able to speed up processing of the claim. Note costs associated with the warranty claim,
other than the rectification of the fault, are the responsibility of the claimant, except those
required under the Australian Consumer Law. The benefits provided to the consumer by the
warranty are in addition to other rights and remedies available to the consumer under the
law.
If missing parts please refer to assembly instructions for identification of said part and
contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure”.
Page 6 of 6