Furniture Solutions Zica User manual

Wood Furniture Maintenance:
Always dust, wipe, and clean with the grain of the wood.
Dust with a soft clean cloth. Dust will scratch the furniture
surface if not removed properly.
If a polished surface becomes foggy, rub it with a cloth
dipped in a solution of one tablespoon vinegar to one litre
of water. Rub softly with the grain until the surface is
completely dry.
Soap and water are not advisable for wood surface.
Water can penetrate the finish and raise the grain on
wood, causing damage.
The Enemies of Wood:
Moisture is wood's worst enemy.
Liquid spills should be gently wipe up immediately.
Coasters should be used under all beverages.
Do not allow rubber or vinyl materials to lie on the
furniture.
Chemicals in rubber may leave a stain. Put a strip of felt
or leather under accessories that have rubber or vinyl.
Heat creates a chemical change in the furniture's finish,
which result in a white spot.
Use protective pads under hot dishes, appliances, etc.
Sunlight's ultraviolet rays can damage the finish of
furniture. Do not place furniture directly against a heater
or radiator and do not place in the path of hot streams of
air from central heating.This will cause extreme localized
drying of the wood.
Your furniture purchase is an investment.
Here are a few tips to maximize the lifetime of your furniture with a minimum amount of effort.
Properly caring for your furniture can help ensure that it looks great year after year.
Page 1 of 6
Zica Dining Table
Made in China
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St, Revesby, NSW. 2212Y
Item# 18ZIC05AB
Size:114cm Round
Stain: Aged Barley
Iron Work Maintenance:
Keep dust free; Bolts and screws must be checked and
re-tightened as necessary or minimum very 6 months.
Paint chips should be touched up as they occur. When bare
metal is exposed to environment, metal will first oxidize and
next stage will be rust, causing structural integrity to be
compromised.
The Enemies Iron Work:
All iron or steel products are painted to protect metal from the
elements.
Do not immerse in water. Liquid spills should cleaned off
immediately. Alcohol, fruit juice etc are acidic and can cause
paint finish to change colour. When cleaning please use only
Ph neutral products.

PRE-ASSEMBLY PREPARATION
Avoid use of powered/battery drills.
Improper use of drills can irreversible damage fittings.
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Ensure to check all components for any damage before assembly. Please report any
damage found to below, if possible forward images of component to below
5. Always read the assembly instructions carefully before beginning assembly.
6. Keep all hardware parts and packaging out of reach of small children.
7. Do not over tighten the screws and bolts as this may damage the threads
2
10
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2
Page 2 of 6
Important Advice:
Never place hot or cold items on surface without proper
insulation. Always use place mats and drink coasters. Always
clean up spills immediatly. Standing or sittting on table can
cause harm to yourself as well as your furniture. Never drag
table always lift to move, a second person will be required.
For any assistance with assembly or for missing parts
Please contact: Place of purchase or Furniture Solutions.
Customer Service (Australia) Phone-1300 794 188
Email- [email protected]

A1PC
C
D
4X4mm
E1PC
B
6mm X 40mm
8PCS
9PCS
9PCS
φ6.5mm
6mm X 18mm
φ6.5mm *φ19
Page 3 of 6
Zica DiningTable
Hardware List
PZC450T-ALEV
Leveler
Pre-Fitted
PZC450T-ABLP
Bottom Leg Frame
PZC450T-ATLP
Top Leg Frame
Component List
PZC450T-ATT
Table Top

B
C
D
C
D
A
B
C
D
B
C
D
B
C
D
*Do not tighten screws & bolts until the entire item is completely assembled.
Page 4 of 6
Assembly Instructions
Please arrange table top as shown in diagram.
Ensure the surface is level, clean and soft.
Suggest a clean blanket or similar.
Please identify the top leg.
At the junction of the two legs one will have a
hole all the way thru and other will have
threading and block end.
Top leg is threaded model.
As shown in diagram Aline hole in top leg with
threaded holes in table top, then take bolt [B]
add spring washer [C] also add flat washer [D].
Insert thru hole as shown, then by hand seat
thread correctly, turn 2-3 times and check bolt
has gripped and is square. Repeat for other 3
bolts. You may at this stage take up the slack
and tighten bolts until they are finger tight only.
Move 2 Step 2.
Next take bottom leg and link the two junctions
as shown.
Take bolt [A] add spring washer [C] then add flat
washer [D]. Insert bolt into hole at junction,
ensure to seat thread correctly by turn bolt by
hand 2-3 times. Check bolt has gripped.
Next Aline the holes in bottom leg as in step one
and proceed to add bolts and washer as
previously instructed.
Now all bolts are fitted correctly, do a visual
check all pieces are square and aliened properly
take tool provided [E] and start to tighten bolts.
Please start with the bolt at junction of legs.
Note do not over tighten as you may
inadvertently cause damage to fittings.
Now with the help of a second person lift table
into the air and rotate mid air until you can place
table on all four feet at the same time.

SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products
.
Please be advised that heat sources such as direct sunlight, log fires, heaters and air
conditioners can have adverse affects on your furniture.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
DO NOT
•Place in direct sunlight.
•Place in close proximity to open flame or heaters.
•Place in direct line of air conditioning ducting.
Safety warnings
•DO NOT:
•drop, drag or strike table surface
•sit or stand upon the table surfaces
•place heavy objects on glass
•place very hot or cold items on the table surface unless adequately thick table mats are
used to prevent such items coming in contact with the surface
•scratch the surface or using as a chopping surface
•allow children to play under tables
•Never drag table always move by lifting
•Clean only as per instructions on previous page. Do not use washing powders or any
other substances containing abrasives that may potentially scratch the surface
CHAIRS AND STOOLS
•Do not:
•Use chair/stool as a ladder
•Climb on the chair/stool
•Stand on the foot-rest of the chair, as this could lead to the stool becoming unbalanced
and overturning
Page 5 of 6

WARRANTY DETAIL
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation,
chipping/scratching, exposure to extreme heat/cold, mould/mildew, hardware corrosion,
misuse of the products & defects caused by failure in duty of care for the product in
accordance with the care instructions. Warranty only extends to original purchaser and is
not transferable, except when given as a gift.
Notice:
While every effort is made to use quality materials our products are limited in design for
domestic use only & are not suitable for commercial use.
Care should be taken not to place product near heat sources.
Duty of care:
While every attempt is made to supply product using quality components there is always a
need from consumer to help ensure long life of use for product. Instruction manuals are
designed with the nature of materials used in construction of the product.
*Proper use of item only what it is designed to do
*Regular maintenance and cleaning
In areas of high content of salt air, pollution and moisture more frequent cleaning is required.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required
before proceeding with any claim. In the case of product defects providing photos may be
able to speed up processing of the claim. If missing parts please refer to assembly
instructions for identification of said part and contact either of the above. Costs associated
with the warranty claim, other than the rectification of the fault, are the responsibility of
the claimant.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
The benefits provided to the consumer by the warranty are in addition to other rights and
remedies available to the consumer under the law.
Page 6 of 6