Furniture Solutions 21BEL12.S User manual

Page 1 of 8
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au
Instruction Manual
BELLE BUFFET 4 DOORS/4 DRAWERS
157*46*91.5cm
Code: 21BEL12.S
21BEL12.S

Please contact your place of purchase or
Furniture Solutions Customer Service (Australia)
Email: [email protected]
Phone: [phone]
PRODUCT SAFETY WARNING
Special handling is required when you work with heavy furniture.
It is recommend up to four person be available when moving or assembling this product.
Choose Location for assembly with below in mind
Level, Spacious, Clean and close to area item will be used.
To protect floor surface and product we recommend the use of a soft
clean blanket or like item on your work space.
Ensure you have all components required to complete assembly
Check components for any damage
Ensure you check off hardware list and identify what they are
Have you read instruction from start to finish
Safety
Never allow children to play in your work space
Ensure to keep small parts away form children. To avoid choke risk.
Never fully extend yourself when assembling or lifting componenets
Avoid use of powered/battery drills.
Improper use of drills can irreversibly damage fittings
Improper assembly does fall under warrantable claim
Special Information unique to your product selection
Missing Parts, Damaged Component, Will not go together
Pre-Assembly Preparation
Before you start check off below
HEAVY
HANDLE
WITH CARE
TO
Please retain your assembly
instruction for future use.
30
21BEL12.S
Page 2 of 8

ATTACHING FEET
Select a clean, soft and flat surface close to the final intended location. A rug or carpet is good.
Gently roll the Buffet over until it is resting on it's top.
Securely screw the bolts mounted on the feet into the nuts fitted to the cabinet plinth base.
Screw the Centre Support leg onto the pre-fitted nut.
Refer Page 4 for correct adjustment of Center Support Leg after Buffet is in its final position.
Do not overtighten feet or legs.
Step 1 - Minimum 2 people required
Locate feet which are packed in protective wrapping inside Buffet
Step 2
! A minimum of 2 people are required to attach feet.
Avoid serious personal injury or damage to your Buffet
Step 3 - Minimum 2 people required
Carefully roll the Buffet back onto it's feet, taking care to apply minimum forced onto the feet.
PROCEED TO FITTING OF SHELF SUPPORTS AND INSTALLATION OF SHELVING
21BEL12.S
Page 3 of 8

8 PCS each
FITTING SHELVES
Fitting shelves
Push shelf support (A) firmly into pre-drilled holes until shelf support pin is fully pushed in.
Make sure all shelf supports are located at the same level. This can most easily be done by
counting the number of holes from top or bottom.
Gently slide shelf into position on top of the support, taking care not to damage the shelf
and checking that it is sitting on the top of each shelf support.
Using a Phillips Head screwdriver fit the screws through the hole in each shelf support and
firmly secure to the underside of each shelf.
DO NOT USE POWER TOOLS AND DO NOT OVERTIGHTEN SCREWS
Shelf support and screw
PROCEED TO ADJUSTING CENTRE SUPPORT LEG
Page 4 of 8 21BEL12.S

Adjusting Centre Support Leg
The cabinet is fitted with support legs to ensure the middle sections are fully supported.
They are fitted with height adjustable feet to allow for uneven floors.
After moving the cabinet to it's final position the support legs need to be adjusted so that
they make contact with the floor.
To do this, simply reach under the cabinet and twist the foot to screw it in or out to the
required height.
NOTE: Legs must be adjusted until they are only just in contact with the ground.
Do not apply any further screwing force once ground contact has been acheived.
Please contact your place of purchase or
Furniture Solutions Customer Service (Australia)
Email: [email protected]
Phone: [phone]
Help: Missing Parts, Damaged Component, will not go together
21BEL12.S
Page 5 of 8
CENTRE SUPPORT LEG
PROCEED TO INSTRUCTIONS FOR FITTING OF ANTI-TIPPING KIT

21BEL12.S
Page 6 of 8
ANTI-TIPPING KIT INSTRUCTIONS
Installation Instructions
1. Attach a bracket (A) to the wallboard with long screws provided.
2. Attach second bracket (A) to rear of the furniture frame under the top with the short screws provided.
Make sure it is screwed into the frame, not just the backing board.
3. Move the furniture into its final intended position.
4. Thread the strap (B) through the slots in the brackets and tighten until snug. Do not overtighten.
5. Make sure the brackets are firmly attched to the the wall/furniture and tat the strap is snug.
A
(2 x Brackets)
B
(1 x Strap)
C
(2 x Short Screws)
D
(2 x Long Screws)
Hardware enclosed:

SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products.
Please be advised that heat sources such as direct sunlight, log fires, heaters and air
conditioners can have adverse affects on your furniture.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
DO NOT
•place in direct sunlight.
•place in close proximity to open flame or heaters.
•place in direct line of air conditioning ducting.
Safety warnings
DO NOT:
•drop, drag or strike table surface
•sit or stand upon the table surfaces
•place heavy objects on table top
•place very hot or cold items on the table surface unless adequately thick table mats are
used to prevent such items coming in contact with the surface
•scratch the surface or using as a chopping surface
•allow children to play under tables
•Never drag table always move by lifting
•Clean only as per instructions on previous page. Do not use washing powders or any
other substances containing abrasives that may potentially scratch the surface
Chairs and Stools
Do not:
•use chair/stool as a ladder
•climb on the chair/stool
•stand on the foot-rest of the chair, as this could lead to the stool becoming unbalanced
and overturning
•drag chair always lift to move
21BEL12.S
Page 7 of 8

1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty workmanship
for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation,
chipping/scratching, exposure to extreme heat/cold, mould/mildew, hardware corrosion, misuse
of the products & defects caused by failure in duty of care for the product in accordance with the
care instructions. Warranty only extends to original purchaser and is not transferable, except when
given as a gift.
Notice:
While every effort is made to use quality materials our products are limited in design for domestic
use only & are not suitable for commercial use.
Care should be taken not to place product near heat sources.
Duty of care:
While every attempt is made to supply product using quality components there is always a need
from consumer to help ensure long life of use for product.
Instruction manuals are designed with the nature of materials used in construction of the product.
*Proper use of item only what it is designed to do
*Regular maintenance and cleaning
In areas of high content of salt air, pollution & moisture require more frequent cleaning.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below.
Proof of purchase will be required before proceeding with any claim. In the case of product
defects providing photos may be able to speed up processing of the claim.
Note costs associated with the warranty claim, other than the rectification of the fault, are the
responsibility of the claimant, except those required under the Australian Consumer Law.
The benefits provided to the consumer by the warranty are in addition to other rights and
remedies available to the consumer under the law.
If missing parts please refer to assembly instructions for identification of said part and contact
either of the above.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure.
21BEL12.S
Warranty Detail
Page 8 of 8