Furuno RD-30 User manual

Installation Manual
MULTI DISPLAY RD-30
SAFETY INSTRUCTIONS....................................................................i
SYSTEM CONFIGURATION...............................................................ii
EQUIPMENT LISTS...........................................................................iii
1. INSTALLATION...............................................................................1
1.1 Installation of Display Unit........................................................................................1
1.2 Wiring.......................................................................................................................3
2. INITIAL SETTINGS.........................................................................7
2.1 Data Sentence Description ......................................................................................7
2.2 IEC 61162-1 (NMEA 0183) Input Data Sentences ...................................................8
2.3 Setting Input/Output.................................................................................................9
PACKING LIST................................................................................A-1
OUTLINE DRAWINGS....................................................................D-1
INTERCONNECTION DIAGRAM.................................................... S-1
www.reelschematic.com
www.reelschematic.com

Your Local Agent/DealerYour Local Agent/Dealer
9-52 Ashihara-cho,9-52 Ashihara-cho,
Nishinomi
y
a, Ja
p
anNishinomi
y
a, Ja
p
an
Tele
p
hone :Tele
p
hone : 0798-65-21110798-65-2111
Telefax :Telefax : 0798-65-42000798-65-4200
F
IRST EDITION :
F
IRST EDITION : MAR.MAR. 20012001
Printed in JapanPrinted in Japan
A
ll ri
g
hts reserved.
A
ll ri
g
hts reserved. E1E1 :: FEB.FEB. 03,200303,2003
PUB.No.PUB.No. IME-44130-E1IME-44130-E1
*00080917801**00080917801*
*00080917801**00080917801*
(( YOSHYOSH )) RD-30RD-30 * 0 0 0 8 0 9 1 7 8 0 1 ** 0 0 0 8 0 9 1 7 8 0 1 *
*IME44130E10**IME44130E10*
*IME44130E10**IME44130E10*
* I M E 4 4 1 3 0 E 1 ** I M E 4 4 1 3 0 E 1 *
www.reelschematic.com
www.reelschematic.com

i
SAFETY INSTRUCTIONS
WARNING
Turn off the power at the
switchboard before beginning the
installation.
Fire or electrical shock can result if the
power is left on.
Be sure that the power supply is
compatible with the voltage rating of
the equipment.
Connection of an incorrect power
supply can cause fire or equipment
damage. The voltage rating of the
equipment appears on the label above
the power connector.
Do not open the cover unless totally
familiar with electrical circuits and
service manual.
Improper handling can result in
electrical shock.
CAUTION
Observe the following compass
safe distances to prevent
interference to a magnetic
compass:
Ground the equipment to
prevent mutual
interference.
Display
unit
Standard Steering
0.35 m 0.25 m
www.reelschematic.com
www.reelschematic.com

ii
SYSTEM CONFIGURATION
Multi display
RD-30
Multi display
RD-30
Multi display
RD-30
GPS receiver
GP-310B
GPS receiver
GP-310B
Sensor
Navigator
Ship's mains
12-24 VDC
: Standard
: Option
MENU
PWR
*
ENT
DISP DIM
FURUNO
RD-30
MENU
PWR
*
ENT
DISP DIM
FURUNO
RD-30
MENU
PWR
*
ENT
DISP DIM
FURUNO
RD-30
Sensor
www.reelschematic.com
www.reelschematic.com

iii
EQUIPMENT LIST
Standard supply
No. Name Type Code No. Qty Remarks
1 Multi Display RD-30 - 1
2 Spare Parts SP14-02901 - 1 set
3 Installation
Materials CP14-06000 - 1 set +Tapping screw (4 pcs)
MJ-A7SPF0005-020
4 Accessories FP14-02801 - 1 set Hard cover
Optional supply
No. Name Type Code No. Qty Remarks
1 Flush Mount Kit S OP20-17 000-040-720
2 Flush Mount Kit F OP20-29 000-041-405 1 For flush
mounting the
display unit
MJ-A7SPF0005-020 000-139-384 1 Power, signal
MJ-A7SPF0006-100 000-143-578 1 7P-7P
cross cable
3 CableAssy.
MJ-A7SPF/SRMD-100 000-144-534 1 7P-7P
straight cable
Sensors available
No. Name Type Code No. Qty Remarks
1 Smart Sensor 235DT-MSE 000-144-981 1 Depth & Temperature
Sensor
2 Smart Sensor 235DT-PSE 000-144-982 1 Depth & Temperature
Sensor
3 Smart Sensor 235DST-PWE 000-144-983 1 Depth, Speed and
Temperature Sensor
4 Smart Sensor 235DHT-LMSE 000-144-984 1 Depth and High Precision
Temperature Sensor
5 Smart Sensor 235DHT-MSE 000-144-985 1 Depth and High Precision
Temperature Sensor
For technical specifications seeAirmar’s technical data.
www.reelschematic.com
www.reelschematic.com

This page is intentionally left blank.
www.reelschematic.com
www.reelschematic.com

1
1. INSTALLATION
1.1 Installation of Display Unit
Mounting considerations
The display unit can be installed on a tabletop, on the overhead, or in a
panel (optional flush mounting kit required). Refer to the outline drawings
at the end of this manual for installation instructions. When selecting a
mounting location, keep in mind the following points:
• Locate the unit away from exhaust pipes and vents.
• The mounting location should be well ventilated.
• Mount the unit where shock and vibration are minimal.
• Locate the unit away from equipment which generates electromagnetic
fields such as a motor or generator.
• Allow sufficient maintenance space at the sides and rear of the unit and
leave sufficient slack in cables, to facilitate maintenance and servicing.
• Observe the following compass safe distances to prevent deviation of a
magnetic compass.
Standard compass, 0.35 m, Steering compass, 0.25 m.
Tabletop and overhead mounting
Tabletop Overhead
Figure 1-1 Tabletop and overhead mounting methods
www.reelschematic.com
www.reelschematic.com

2
Flush mounting
There are two types of flush mount kits, F type and S type. For details, see
the outline drawings at the back of this manual.
F type
Flush mount kit F (Type: OP20-29, Code No.: 000-041-405)
No. Name Type Code No. Qty Remarks
1 Cosmetic Panel 20-016-1051 100-251-370 1
2 + Tapping Screw 5x20 SUS304 000-802-840 4
3 Hex Bolt M6x12 SUS304 000-862-127 2
4 Spring Washer M6 SUS304 000-864-260 2
1. Make a cutout of 183 X 92 mm.
2. Attach the cosmetic panel (supplied) to the display unit with hex bolts
(M6X12, supplied) and spring washers (M6, supplied).
3. Fix the display unit to the mounting location with four tapping screws
(5X20, supplied).
S type
Flush mount kit S (Type: OP20-17, Code No.: 000-040-720)
No. Name Type Code No. Qty Remarks
1 Fixing Metal 20-007-2401 100-183-190 2
2 Wing Bolt M4x30 YBSC2
MBN12 000-804-799 4
3 Hex Bolt M6x12 SUS304 000-862-127 2
4 Wing Nut M4 YBSC2
MBN12 000-863-306 4
5 Spring Washer M6 SUS304 000-864-260 2
1. Make a cutout of 167 X 92 mm.
2. Attach two fixing metals (supplied) to the display unit with hex bolts
(M6X12, supplied) and spring washers (M6, supplied).
3. Screw four wing bolts (supplied) into wing nuts (supplied).
4. Fasten the display unit to the mounting location with four sets of wing
bolts and nuts assembled at step 3.
www.reelschematic.com
www.reelschematic.com

3
1.2 Wiring
The figure below shows where to connect cables on the rear of the display
unit.
Black Red
POWER
(12-24 VDC) Ground
1A FUSE
(+ Line)
DISPLAY
UNIT
+
-
DISPLAY
UNIT
GPS
RECEIVER
Ground the equipment to
prevent mutual interference.
CAUTION
Figure 1-2 Wiring
Note: The fuse holder contains a spring which fixes the fuse. To prevent
detachment of the spring, which would cause loss of power, tie the
line as shown in Figure 1-3.
Fuse holder
+ line (red)
Tie here.
Figure 1-3 How to fix spring in fuse holder
www.reelschematic.com
www.reelschematic.com

4
Grounding
The display unit contains a CPU. While it is operating, it radiates noise,
which can interfere with radio equipment. Ground the unit as follows to
prevent interference:
• The ground wire should be 1.25 sq or larger.
• The ground wire should be as short as possible.
• The signal ground and frame ground are separated, however the power
line is not isolated. Therefore, do not connect the signal ground to the
frame ground when connecting other equipment to a positive ground
battery.
External equipment
The power supply port (IN/OUT port) is commonly used for connection of
external equipment such as navigation equipment or a PC. Refer to the
interconnection diagram on page S-1 for connection.
IN/OUT port
Connector Remarks
1TD-A
2TD-BIEC61162-1/NMEA 0183
3 RD-H
4 RD-C IEC61162-1/NMEA 0183
5+V
6GNDPower supply (12-
24VDC)
(INPUT)
7FG
AUX port
Connector Remarks
1TD-A
2TD-BIEC61162-1/NMEA 0183
3 RD-H
4 RD-C IEC61162-1/NMEA 0183
5 +Vout
6GNDMax 300 mA
(OUTPUT)
7FG
www.reelschematic.com
www.reelschematic.com