Gama Sonic BAYTOWN II 105BSG01 User manual

BAYTOWN II BULB
SOLAR LAMP POST
WITH GS LED
SOLAR BULB
Model: 105BSG01/ 105BSG21
Version 1.2
US Patent #9458970 #7172307
Instruction Manual

For optimum light duration throughout the night, it is very important to place your solar lamp in a spot
where it will receive the maximum amount of direct sunlight throughout the day.
page 2
Thank you for your purchase. GAMA SONIC® solar charged lights are brighter and last all night with a full day solar charge.
Unique designs, superior light output, and numerous installation options confirm the outstanding value of our product.
For technical assistance and more information call our Toll-Free number:
800-835-4113 (only within the US)
Or
visit our website or download the latest version of your instruction manual:
www.gamasonic.com Or www.gamasonic.com/user-guides
Please read the instruction manual carefully to obtain the best results from your purchase.
What'sinside
A. Finial
B. Top
D. Body
H. Anchor
I. Turning bar
G. Base plate
Screws and caps
F. 3" Fitter
GS LED Bulb
E. Stem
C. Lens and cone
Open your package and remove the contents. Check to
make sure all pieces are present and accounted for.
NOTE: For best results, the solar lamp post must be charged for two sunny days on the “ON” position,
WARNING: GAMA SONIC® Light bulbs are built and
designed for Gama Sonic products only. They are not
designed to be used in other electrical sockets.
For the same reason, regular AC and/or Low Voltage
bulbs cannot be used in Gama Sonic products.
WARNING: GAMA SONIC® Light bulbs are built and
designed for Gama Sonic products only. They are not
Side handles
3" Fitter
WARNING: GAMA SONIC® Light bulbs are built and
designed for Gama Sonic products only. They are not
For the same reason, regular AC and/or Low Voltage

page 3
1. Attach the body (D) to
the stem(E) with the four
supplied screws, as shown.
8.1.
Mark three holes using the
base plate as a template.
Use electric drill to make the
holes. Place anchors in holes
and secure with screws .
9.1. Attach Part
(G) to Part (H)
Using the four
small screws from,
as shown
8.2.
Attach the three
decorative caps provided.
Continue by screwing the
pole to the base.
9.2. Insert the
Turning bar (I) in
the hole through
the anchor stake
(G+H) as shown.
9.4 Occasionally check the
anchor Level Tool to ensure
your Post is straight.
9.5 Stop turning once Part (G) is flush with
ground.
9.6 Remove the Turning Bar (I).
9.7 Screw the Pole to the Anchor.
2.Place the lens and
cone (C) into the
body (D+E).
4. Attach top (B) to the
body (C+D+E) with
the two supplied
screw caps
5. Attach Side handles
provided.
6. Screw Finial to the top.
7. Assemble pole by screwing the four pieces together.
Assembly Instructions: Installation on flat surface
(Without the Anchor):
EZ Anchor
Installation
Instructions:
3.Install the
bulb and turn
on switch
to desired
setting
Operation Switch
bulb and turn
Operation Switch
9.1
(G) to Part (H)
Using the four
small screws from,
as shown
9.2.
Turning bar (I) in
the hole through
the anchor stake
(G+H) as shown.
9.4
anchor Level Tool to ensure
your Post is straight.
9.5
ground.
9.6
9.7
Attach top (B) to the
body (C+D+E) with
Screw Finial to the top.
Assemble pole by screwing the four pieces together.
EZ Anchor
Installation
Instructions:
Operation Switch
9.3. Place anchor in desired location
and apply downward pressure while
turning the Turning bar clock wise.
Occasionally check the
D
E
D+E
B
C+D+E
C
G
G+H
I
H

page4
Replacing the Batteries
Operation
Instructions
Replacement batteries are available at
www.gamasonic.com or via our Toll free number: [phone]
After several years of use, the battery may need replacing.
This product comes with two battery compartments, and one battery is installed.
If your solar panel is exposed to the sun for more than 4 hours a day, you
can choose to add another battery. The second battery will extend the lights
duration, especially on cloudy days. It will not change the brightness of the lamp.
1. Unscrew the two screw caps and detach the top (B). Make sure the ON/OFF
switch is in the OFF (O) position.
2. Unscrew the battery compartment (Fig. 1) screw located on the silver
reflector and remove the compartment door.
3. Unclip the connector and remove the old battery. Make sure the new
battery is a Gama Sonic – 3.2V/1,500mAh, Li-ion Rechargeable battery with
connector.
4. Clip on new battery and install into the battery compartment. Screw back
battery compartment screw.
5. Reattach the top and secure with the 2 screw caps.
1. Remove the Top (B) by
unscrewing the 2 screw caps.
Screw the GS LED lightbulb
into the socket. Turn on
switch to desired setting
high or low (for longer
duration). The Solar Lamp
will automatically operate at
dusk.
2. Reattach the Top (B) and
secure with the 2 screw caps.
Maintenance
Clean the solar module regularly with a damp towel to guarantee optimum
performance of the solar panel. Do not use any type of solvent for cleaning and
be careful not to put too much pressure on the module while cleaning.
Trouble Shooting
If your solar charged light does not come on at dusk despite
observance of all the instructions, please try the following steps:
1. Make sure that the solar light is not being affected by any other light source.
2. Ensure the solar light is not positioned in the shade during the day.
3. Make sure the switch in the lamp head is in the” ON” position.
4. Check that the batteries are installed correctly.
NOTE: The performance of the solar light will vary with the time of year. It will
deliver longer duration when it has had a full day in the sun rather than a day in
overcast weather.
WINTERTIME TIPS: For optimal performance, be sure to remove any snow
or debris accumulation from solar panel(s). A solar panel free of debris will
charge the batteries much more efficiently.
WARNING: Please keep out of reach of children.
4. Clip on new battery and install into the battery compartment. Screw back
5. Reattach the top and secure with the 2 screw caps.
Operation
Switch
secure with the 2 screw caps.
Maintenance
Operation
Switch
WARNING: Do not dispose of Li-Ion battery
in the regular trash, municipal waste stream
or by fire as batteries may leak or explode.
Do not open, short circuit, or mutilate
batteries as injury may occur. Preserve our
environment by recycling Li-Ion batteries or
disposing of them in accordance with local,
State and federal regulations. Do not mix old
and new batteries.