Gardeners 8600288 User manual

1-800-876-5520 • gardeners.com
[e-mail]
8% of our profits go back to our communities.
Learn more at gardeners.com/FoRCE-FoR-GoOD
V Rev /#, , 
Hemp Grow Frame, Lights and Tray
Frame Assembly
Parts List
() " TUBES
() " TUBES
() " TUBES
() " TUBES
() -WAY CONNECTORS
() -WAY CONNECTORS
() T CONNECTORS
() WIRE SHELVES
1. Assemble the frame as shown in Fig. 1. Make sure the TUBES are fully pressed
into the CONNECTORS.
2. Place the WIRE SHELVES on the top and middle tiers of the frame.
Light Assembly
Parts List Tools
() FLAT SUPPORTS ALLEN WRENCH (included)
() LIGHT BRACKETS with CLIPS Phillips or flathead screwdriver (not included)
() LIGHTS
() BINDING BOLT ( pieces)
() BOLTS
() LINKING CABLES
() POWER CORD
() HANGER ASSEMBLIES (Fig. 5 & 6, see reverse side)
3. Line up the holes in the centers of the FLAT SUPPORTS and slide one half of the BINDING BOLT through them. Place the other half
of the BINDING BOLT through the other side and use your screwdriver to attach them (Fig 2.) NOTE: The FLAT SUPPORTS will feel
loose even after tightening.
4. Examine the channels on top of the LIGHT BRACKETS to find the attached nuts (Fig 3.). Use the ALLEN WRENCH to spread them
out and position the holes in the ends of the FLAT SUPPORTS over them. Place a BOLT through each hole and use the ALLEN
WRENCH to tighten them into the nuts.
5. Adjust the ends of the FLAT SUPPORTS so they are centered on the LIGHT BRACKETS, using the numbers on the BRACKETS as a
reference.
over please
FLAT SUPPORTS
(pressed together)
screwdriver
BINDING BOLT
Figure 2
BINDING
BOLT
LIGHT BRACKETS
LIGHT BRACKET
(top channel)
nut
BOLT
FLAT SUPPORTS
Figure 3
BINDING
BOLT
3-WAY
3-WAY
3-WAY
3-WAY
T
4-WAY
4-WAY
27"
18"
14"
28"
28"
28"
28"
28"
27"
18"
14"
FIGURE 1

Light Assembly continued
6. Flip the attached LIGHT BRACKETS and FLAT SUPPORTS upside
down with the attached CLIPS facing up. Use the ALLEN WRENCH to
loosen the nuts in the center of the  outside CLIPS and slide them in
to the  cm spots on the BRACKETS. Tighten them back into place.
7. Examine the ends of the LIGHTS and notice how there are male and
female ends. Using Fig.  as a reference, place the LIGHTS into the
CLIPS attached to the LIGHT BRACKETS with the ends alternating
male and female. Plug the LINKING CABLES and POWER CORD into
the ends of the LIGHTS.
8. Assemble the HANGER KITS by attaching the wire cords to the ring,
carabiner and clip hook as shown in Fig. 5.
9. Snap the  hanger clips onto the ends of the  outside LIGHTS. Slide
the carabiners through the holes in the top of the hanger clips and
position them as shown in Fig 6. Attach the clip hooks to the top
WIRE SHELF so the assembled lights are suspended over the bottom
SHELF.
Light Height
You can position your light at  different heights. The lowest
height is when the HANGER KITs are fully extended. You can also
slide the rings into the carabiners to raise the lights part-way (Fig
6.) or attach the carabiners directly to the top WIRE SHELF.
Final Assembly
Parts List
() COVER
() TRAY
10. Unzip the COVER and slide it over the top of the frame (Fig. ). Place the
TRAY on the floor and plug the POWER CORD into your outlet or timer. Your
assembly is complete!
Please refer to the Gardener's Supply Company Hemp Grow Guide
(included with your Hemp Grow Frame, Lights and Tray)
for complete growing instructions.
LINKING CABLE
POWER
CORD
LIGHTS
LIGHT
BRACKETS
LINKING CABLE
Figure 4
carabiner ring
Figure 5: HANGER KIT assembled
clip hook
wire cords
Figure 6
At lowest height At middle height
carabiner
ring
wire cord
hanger
clip
hanger
clip
carabiner
wire cord
Figure 7