Garland INT10G8SR56-SP User manual

Quick Start Guide
INT10G8SR56-SP / INT10G8LR56-SP
12/2023
Release Version: 4.29.2

Quick Start Guide
EdgeLens | INT10G8XX56-SP | 4.29.2
Copyright © 2023 Garland Technology, LLC. All rights reserved.
No part of this document may be reproduced in any form or by any means without prior written permission
of Garland Technology, LLC.
The Garland Technology trademarks, service marks ("Marks") and other Garland Technology trademarks
are the property of Garland Technology, LLC. PacketMAX Series products of marks are trademarks or
registered trademarks of Garland Technology, LLC. You are not permitted to use these Marks without the
prior written consent of Garland Technology.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Garland
Technology and the customer. All or part of the products, services and features described in this
document may not be within the purchase scope or the usage scope. Unless otherwise specified in the
contract, all statements, information, and recommendations in this document are provided "AS IS" without
warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Garland Technology | 716.242.8500 | garlandtechnology.com/support
Copyright © 2023 Garland Technology, LLC. All rights reserved. 2

Quick Start Guide
EdgeLens | INT10G8XX56-SP | 4.29.2
The 4.29.2 firmware release supports the following configurable options via the Serial Interface.
Enable/Disable Local Authentication
Enable/Disable/Configure IPv4 Management Address/Gateway
Enable/Disable/Configure IPv4 TACACS Primary Authentication
Enable/Disable/Configure IPv4 TACACS Secondary Authentication
Enable/Disable/Configure IPv6 Management Address/Gateway
The units are shipped with the following defaults:
- Default username/password (admin/gtadmin1)
- Local Authentication enabled
- IPv4 management enabled
- The IPv6 management disabled
- IPv4 TACACS Primary Authentication disabled
- IPv4 TACACS Secondary Authentication disabled
The following procedure options are discussed and may be performed as part of the initial turn up.
1. Connect to the Serial Interface
2. Enable/Disable/Configure IPv4 Management Address/Gateway
3. Enable/Disable/Configure IPv6 Management Address/Gateway
4. Enable/Disable Local Authentication
5. Enable/Disable/Configure IPv4 TACACS Primary Authentication
6. Enable/Disable/Configure IPv4 TACACS Secondary Authentication
7. Launch the GUI
1. Connect to the Serial Interface
1. Connect a Serial cable from a COM port on the laptop or PC to the Serial Interface on the unit.
2. Launch Putty and configure the Serial connection as follows:
Speed (baud) 115200
Data bits 8
Stop bits 1
Parity None
Flow Control XON/XOFF
3. Press the enter key and the unit will respond with the login prompt.
4. Enter the default username/password, (admin/gtadmin1). The Main Menu will be displayed.
Garland Technology INT10G8XX56-SP (Code Version: 4.29.2)
Main Menu
Select:
1. Authentication
2. NetworkConfig
3. System reboot
s. sysinfo
0. Logout
Select:
Garland Technology | 716.242.8500 | garlandtechnology.com/support
Copyright © 2023 Garland Technology, LLC. All rights reserved. 3

Quick Start Guide
EdgeLens | INT10G8XX56-SP | 4.29.2
2. Enable/Disable/Configure IPv4 Management Address/Gateway
The IPv4 management interface is enabled by default with a default IPv4 address/gateway,
10.10.10.200/10.10.10.1. The IPv4 and IPv6 management interfaces may be enabled
simultaneously.
Disable IPv4 Management Interface
1. Enter 2. NetworkConfig
2. Enter 2. ipv4 config
3. Enter 1. disable ipv4
4. Enter a. apply new config
Enable IPv4 Management Interface
1. Enter 2. NetworkConfig
2. Enter 2. ipv4 config
3. Enter 1. enable ipv4
4. Enter a. apply new config
Configure IPv4 Management Address/Gateway
1. Enter 2. NetworkConfig
2. Enter 2. ipv4 config
3. Enter 2. ip address
4. Select the backspace button on the keyboard and remove the current IPv4 address
5. Enter the desired IPv4 address (www.xxx.yyy.zzz/xx)
6. Press Enter
7. Enter 3. gateway
8. Select the backspace button on the keyboard and remove the current IPv4 gateway
9. Enter the desired IPv4 gateway
10. Press Enter
11. Enter a. apply new config
3. Enable/Disable/Configure IPv6 Management Address/Gateway
The IPv6 management interface is disabled by default with a default IPv6 address/gateway,
fd10:1010:2000:ffff:ffff:ffff:ffff:ffff/fd10:1010:1000:ffff:ffff:ffff:ffff:ffff. The IPv6 and IPv4
management interfaces may be enabled simultaneously.
Enable IPv6 Management Interface
1. Enter 2. NetworkConfig
2. Enter 3. ipv6 config
3. Enter 1. enable ipv6
4. Enter a. apply new config
Disable IPv6 Management Interface
1. Enter 2. NetworkConfig
2. Enter 3. ipv6 config
3. Enter 1. disable ipv6
4. Enter a. apply new config
Garland Technology | 716.242.8500 | garlandtechnology.com/support
Copyright © 2023 Garland Technology, LLC. All rights reserved. 4

Quick Start Guide
EdgeLens | INT10G8XX56-SP | 4.29.2
Configure IPv6 Management Address/Gateway
1. Enter 2. NetworkConfig
2. Enter 3. ipv6 config
3. Enter 2. ipv6 address
4. Select the backspace button on the keyboard and remove the current IPv6 address
5. Enter the desired IPv6 address
6. Press Enter
7. Enter 3. gateway
8. Select the backspace button on the keyboard and remove the current IPv6 gateway
9. Enter the desired IPv6 gateway
10. Press Enter
11. Enter a. apply new config
4. Enable/Disable Local Authentication
Local authentication is enabled by default.
Disable Local Authentication
1. Enter 1. Authentication
2. Enter 1. local authentication off
3. Enter a. Apply
Enable Local Authentication
1. Enter 1. Authentication
2. Enter 1. local authentication on
3. Enter a. Apply
5. Enable/Disable/Configure IPv4 TACACS Primary Authentication
The IPv4 TACACS+ Primary Authentication is disabled by default with a default IPv4 address,
10.10.10.200.
Enable/Configure IPv4 TACACS Primary Authentication
1. Enter 1. Authentication
2. Enter 2. Primary TACACS Menu
3. Enter 1. TACACS Authentication on
4. Enter 2. Change TACACS server IP
5. Press the backspace button on the keyboard and remove the current TACACS IP address
6. Enter the desired TACACS IP address
7. Press Enter
8. Enter 3. Change TACACS server secret. (optional)
9. Press the backspace button on the keyboard and remove the current TACACS secret
10. Enter the desired TACACS secret
11. Press Enter
12. Enter 4. Change TACACS server timeout
13. Enter the desired TACACS timeout (5-60 seconds)
14. Press Enter
15. Enter a. Apply
16. Enter 4. ping www.xxx.yyy.zzz, (optional)
17. Enter 5. test TACACS to www.xxx.yyy.zzz, (optional)
Garland Technology | 716.242.8500 | garlandtechnology.com/support
Copyright © 2023 Garland Technology, LLC. All rights reserved. 5

Quick Start Guide
EdgeLens | INT10G8XX56-SP | 4.29.2
17a. Enter Username
17b. Press Enter
17c. Enter Password
17d. Press Enter
Disable IPv4 TACACS Primary Authentication
1. Enter 1. Authentication
2. Enter 2. Primary TACACS Menu
3. Enter 1. TACACS Authentication off
4. Enter a. Apply
6. Enable/Disable/Configure IPv4 TACACS Secondary Authentication
The IPv4 TACACS Secondary Authentication is disabled by default with a default IPv4 address,
10.10.10.200.
Enable/Configure IPv4 TACACS Secondary Authentication
1. Enter 1. Authentication
2. Enter 3. Secondary TACACS Menu
3. Enter 1. TACACS Authentication on
4. Enter 2. Change TACACS server IP
5. Press the backspace button on the keyboard and remove the current TACACS IP address
6. Enter the desired TACACS IP address
7. Press Enter
8. Enter 3. Change TACACS server secret. (optional)
9. Press the backspace button on the keyboard and remove the current TACACS secret
10. Enter the desired TACACS secret
11. Press Enter
12. Enter 4. Change TACACS server timeout
13. Enter the desired TACACS timeout (5-60 seconds)
14. Press Enter
15. Enter a. Apply
16. Enter 4. ping www.xxx.yyy.zzz, (optional)
17. Enter 5. test TACACS to www.xxx.yyy.zzz, (optional)
17a. Enter Username
17b. Press Enter
17c. Enter Password
17d. Press Enter
Disable IPv4 TACACS Secondary Authentication
1. Enter 1. Authentication
2. Enter 2. Primary TACACS Menu
3. Enter 1. TACACS Authentication off
4. Enter a. Apply
7. Launch the GUI
1. Launch the web browser on the laptop or PC
2. Enter the URL for the desired Garland unit
3. Press Enter
4. Enter the default username/password, (admin/gtadmin1)
Garland Technology | 716.242.8500 | garlandtechnology.com/support
Copyright © 2023 Garland Technology, LLC. All rights reserved. 6