Garland P10GSFPBPFE User manual

User Guide
P10GSFPBPFE
12/2022
Release Version: 4.22.1
1

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Copyright © 2022 Garland Technology, LLC. All rights reserved.
No part of this document may be reproduced in any form or by any means without prior written permission of
Garland Technology, LLC.
The Garland Technology trademarks, service marks ("Marks") and other Garland Technology trademarks are the
property of Garland Technology, LLC. PacketMAX Series products of marks are trademarks or registered
trademarks of Garland Technology, LLC. You are not permitted to use these Marks without the prior written
consent of Garland Technology.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Garland
Technology and the customer. All or part of the products, services and features described in this document may
not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
2

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Table of Contents (click topic to go directly to the page)
1. Dashboard 6
Bypass Mode 6
LED Indications 6
Span Mode 7
LED Indications 7
Span (Packet Inject) Mode 8
LED Indications 8
Breakout Mode 9
LED Indications 9
Filter Mode 10
LED Indications 10
Aggregate Mode 11
LED Indications 11
Filter Tap Mode 12
LED Indications 12
Bypass Filter Mode 13
LED Indications 13
2. System 14
System Info 15
General 15
Admin 15
Users 15
Groups 16
Authentication 16
Local Authentication Disable 17
Local Authentication Enable 17
TACACS Primary Authentication 17
TACACS Test 17
TACACS Ping Test 17
TACACS Secondary Authentication 18
TACACS Test 18
TACACS Ping Test 18
Network Settings 18
IPv4 / Disable 19
IPv4 Enable 19
IPv6 Enable 19
IPv6 Disable 19
Add SSL Certificate 20
Disable Using Uploaded SSL Certificate 20
Date & Time 21
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
3

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Timezone 21
UTC 21
Manually Set Date & Time 21
NTP No Authentication (Symmetric) 21
NTP Authentication (Symmetric) 22
Syslog 22
Syslog Test 23
SNMP 23
SNMP Test 24
Export Configuration 24
Import Configuration 24
Software Upgrade 25
Reboot 25
3. Bypass Mode 26
Bypass Tap Name 28
Heartbeat Settings 28
Taps Settings 28
4. Span Mode 31
5. Span Packet Inject Mode 32
6. Breakout Mode 33
7. Filter Mode 34
Packet Broker 35
Filter Templates 36
Config Map 37
Ingress 37
Filters 38
Egress 39
Config Map Save 39
Modify a Config Map 39
Config Map Statistics 40
Delete Config Map 40
Config Map Priority 41
Method 1 42
Method 2 42
Enable/Disable Config Map 42
Disable Config Map 42
Enable Config Map 42
8. Aggregate Mode 43
9. Filter Tap Mode 44
Packet Broker 45
Filter Templates 46
Config Maps 47
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
4

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Ingress 47
Filter 48
Egress 49
Config Map Save 49
Modify a Config Map 49
Config Map Statistics 50
Delete Config Map 50
Config Map Priority 51
Method 1 51
Method 2 51
Enable/Disable Config Map 52
Disable Config Map 52
Enable Config Map 52
10. Bypass Filter Mode 53
Bypass Taps 54
Bypass Tap Name 55
Heartbeat Settings 55
Taps Settings 55
Filters 58
Filter Templates 59
Config Map 60
Ingress 61
Filters 61
Egress 62
Config Map Save 62
Modify a Config Map 63
Config Map Statistics 63
Delete Config Map 64
Config Map Priority 64
Method 1 65
Method 2 65
Enable/Disable Config Map 65
Disable Config Map 65
Enable Config Map 65
11. Port Info 66
Port Configuration 67
Port Description 67
Set Speed 67
Mode 67
Port Statistics 67
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
5

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
1. Dashboard
This section provides an overview of the dashboard architectures and LED indications. The port
assignments and LED indications will change on the dashboard based on the mode configured.
The dashboard provides an exact detail of the unit’s faceplate. However, some LED indications that
are displayed on the faceplate, are not displayed on the dashboard. The P10GXXBPE supports multiple
modes of operation, Bypass, Span, Span Packet Inject, Breakout, Filter, Aggregate, Filter Tap and
Bypass Filter.
Bypass Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Network Port Link/Activity LED
BP Bypass LED
Port 3 L/A Inline Appliance Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Inline Appliance Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
6

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Span Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Span Port Link/Activity LED
BP N/A
Port 3 L/A Span Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Span Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
7

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Span (Packet Inject) Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Span and Packet Inject Port Link/Activity LED
BP N/A
Port 3 L/A Span and Packet Inject Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Span and Packet Inject Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
8

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Breakout Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Network Port Link/Activity LED
BP N/A
Port 3 L/A Breakout Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Breakout Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
9

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Filter Mode
LED Indications
Port 1 L/A1 Filter Port Link/Activity LED
Port 2 L/A2 Filter Port Link/Activity LED
BP N/A
Port 3 L/A Filter Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Filter Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
10

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Aggregate Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Network Port Link/Activity LED
BP N/A
Port 3 L/A Aggregate Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Aggregate Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
11

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Filter Tap Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Network Port Link/Activity LED
BP N/A
Port 3 L/A Breakout/Aggregate Port Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Breakout/Aggregate Port Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
12

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Bypass Filter Mode
LED Indications
Port 1 L/A1 Network Port Link/Activity LED
Port 2 L/A2 Network Port Link/Activity LED
BP Bypass LED
Port 3 L/A Inline Appliance Link/Activity LED
Port 3 H/M N/A
Port 4 L/A Inline Appliance Link/Activity LED
Port 4 H/M N/A
* The L/A1, L/A2, Port 3 L/A and Port 4 L/A LEDs only indicate link in the GUI.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
13

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
2. System
The following configuration options may be displayed, modified, enabled or disabled under the System
panel.
System Info SNMP
General Export Configuration
Admin Import Configuration
Network Settings Software Upgrade
Date & Time Reboot
Syslog
1. Select System on the Dashboard Menu bar.
The System panel will be displayed. The system configuration options will be displayed on the
left side of the panel.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
14

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
System Info
The System Information panel displays the following.
Chassis Name Chassis Model Chassis Serial Number
MAC Address Software Version
1. Select System Info.
The System Information panel will be displayed.
General
The following configuration options may be displayed or modified.
Chassis Name
Key Press Timeout
1. Select General.
The General System Settings panel will be displayed.
2. Select Edit Configuration.
3. Enter the desired Chassis Name.
4. Enter the desired Key Press Timeout.
5. Select Save to save updates.
6. Select Cancel to return to the General System Settings panel.
Admin
The following configuration options may be displayed, modified, enabled or disabled.
Users
Groups
Authentication
Local
TACACS Primary
TACACS Secondary
1. Select Admin.
The Admin Settings panel will displayed.
Users
The default user is “admin”. Changes to the default user “admin” are allowed. However, the “admin”
user may not be deleted. Users displayed on the Admin Settings panel are for local authentication
only, not used for TACACS.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
15

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
1. Select Users + to create a new user.
The Create New User panel will be displayed.
2. Enter the Username.
3. Enter the Password.
4. Select the group for the user.
5. Select Save to save updates.
The new user will be displayed on the Admin Settings panel.
6. Select Cancel to return to the Admin Settings panel.
7. Edit the username, password or assigned group by selecting the pencil.
8. Delete the user by selecting the Red X.
Groups
The group defines the authorization for a user or group of users. A group may be used for local
or TACACS authorization. In Use “true” means that there is at least one local user assigned to
the group. If a group is used by TACACS, the In Use will indicate “false”. There are three default
groups, admin, OPER and NOC. All three groups may be modified, however only the OPER and
NOC groups may be deleted.
1. Select Groups + to create a new group.
The Create New Group panel will be displayed.
2. Enter the Group Name.
3. Select the desired privileges.
4. Select Save to save updates.
The new group will be displayed on the Admin Settings panel.
5. Select Cancel to return to the Admin Settings panel.
6. Modify the group privileges by selecting the pencil.
7. Deleted the group by selecting the Red X.
If a group has at least one user assigned it cannot be deleted.
Authentication
Two authentication options are supported, local or TACACS. TACACS authentication supports two
options, primary and secondary. The TACACS primary and secondary options may be enabled or
disabled independently. Local or TACACS authentication may be enabled or disabled independently,
however, at least one option must be enabled. The TACACS primary or secondary function supports
IPv4 only, IPv6 is not supported.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
16

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
1. Select Authentication Settings.
The Authentication Settings panel will be displayed. Local authentication is enabled by default.
Local Authentication Disable
1. Deselect Local Authentication.
Local authentication may only be disabled provided that TACACS authentication, primary
or secondary has previously been enabled.
2. Select Save.
Local Authentication Enable
1. Select Local Authentication.
2. Select Save.
TACACS Primary Authentication
1. Select Enable Primary.
The TACACS Primary panel will be displayed.
2. Enter the IP Address, IPv4 or IPv6.
3. Enter the Secret Word, (optional).
4. Select Save to save updates.
5. Select Cancel to return the Admin Settings panel.
TACACS Test
This option may be used to verify the authentication of a TACACS user, password and
authorization group. The TACACS Test option will be active only if TACACS authentication
has previously been enabled.
1. Select TACACS Test.
The TACACS Test panel will appear.
2. Select Primary.
3. Enter the Username.
4. Enter the Password.
5. Select Test.
The GUI will display the results of the test, “Authentication Test Successful”. As well as
messages for “authentication:Success”, authorization:Success” and
“authorization:group:abcdef.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
17

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
TACACS Ping Test
This option may be used to verify the network connectivity from the unit to the TACACS server.
The TACACS Ping option will be active only if TACACS authentication has been previously enabled.
1. Select TACACS 1 Ping.
The GUI will display the results of the ping, “TACACS 1 Ping Successful”.
TACACS Secondary Authentication
1. Select Enable Secondary.
The TACACS Secondary panel will be displayed.
2. Enter the IP Address, IPv4 or IPv6.
3. Enter the Secret Word, (optional).
4. Select Save to save updates.
5. Select Cancel to return the Admin Settings panel.
TACACS Test
This option may be used to verify the authentication of a TACACS user, password and
authorization group. The TACACS Test option will be active only if TACACS authentication
has previously been enabled.
1. Select TACACS Test.
The TACACS Test panel will appear.
2. Select Secondary.
3. Enter the Username.
4. Enter the Password.
5. Select Test.
The GUI will display the results of the test, “Authentication Test Successful”. As well as
messages for “authentication:Success”, authorization:Success” and
“authorization:group:abcdef.
TACACS Ping Test
This option may be used to verify the network connectivity from the unit to the TACACS server.
The TACACS Ping option will be active only if TACACS authentication has been previously enabled.
1. Select TACACS 2 Ping.
The GUI will display the results of the ping, “TACACS 2 Ping Successful”.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
18

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
Network Settings
Upon the initial turn up via the serial interface the IPv4 address, IPv4 gateway, IPv6 address and IPv6
gateway may have been already established. The IPv4 and IPv6 management interfaces may be
enabled or disabled independently as well as both enabled or disabled simultaneously. If the IPv4
and IPv6 management interfaces are disabled simultaneously, access is only allowed via the serial
interface. Any modifications made to any setting option will cause GUI disruption for about 60 seconds.
Also note that modifying the management interfaces may cause network disruption if prior consideration
and planning have not been performed.
The default system network configurations are as follows:
IPv4 enabled
IPv4 address 10.10.10.200
IPv4 gateway 10.10.10.1
IPv6 is disabled.
Via the GUI, the following options may be displayed, modified, enabled or disabled.
IPv4 Enable/Disable IPv4 Address IPv4 Gateway
IPv6 Enable/Disable IPv6 Address IPv6 Gateway
SSL Certificate Loaded
Using Uploaded SSL Certificate
1. Select Network Settings.
The Network Settings panel will be displayed with the current configuration.
IPv4 / Disable
1. Deselect Enable IPv4.
2. Select Save.
If the IPv6 management interface has not been enabled the GUI will display a
message “Disabling IPv4 and IPv6, GUI will disconnect. Are you sure?
3. Select OK.
IPv4 Enable
1. Select Enable IPv4.
2. Enter the desired Address.
3. Enter the desired Gateway.
4. Select Save.
IPv6 Enable
1. Select Enable IPv6.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
19

User Guide
XtraTAP™ Portable Packet Broker | P10GSFPBPFE | 4.22.1
2. Enter the desired Address.
3. Enter the desired Gateway.
4. Select Save.
IPv6 Disable
1. Deselect Enable IPv6.
2. Select Save.
If the IPv4 management interface has not been enabled the GUI will display a
message “Disabling IPv4 and IPv6, GUI will disconnect. Are you sure?
3. Select OK.
Add SSL Certificate
Uploading a custom SSL certificate involves two files. The cert.pem file and key.pem file. The unit will
validate these files during the upload. If the files do not match or one of the files are corrupted the unit will
abort the upload.
1. Select Add SSL Certificate.
The Select Certificate and Select Key File panel will appear.
2. Select Choose File for Select Certificate.
3. Select the desired cert.pem file.
4. Select Open.
5. Select the Choose File for Select Key File.
6. Select the desired key.pem file.
7. Select Open.
8. Select Upload.
The GUI message will be displayed, “Please wait. Browser will refresh after 90 seconds”.
9. Verify SSL Certificate Loaded “true”.
10. Verify Using Uploaded SSL Certificate “true”.
Disable Using Uploaded SSL Certificate
1. Select Edit Settings.
2. Deselect Using Uploaded SSL Certificate.
3. Select Save.
The GUI message will be displayed,”Saved Settings. Changes will cause network
connectivity disruption for about 60 seconds”.
Garland Technology | 716.242.8500 | www.garlandtechnology.com
Copyright © 2022 Garland Technology, LLC. All rights reserved.
20