Garland P1GCSSP User manual

User Guide
Data Diode SPAN TAP |P1GCSSP |1.2.58
The P1GCSSP is a portable 10M, 100M, 1G TAP designed for out-of-band monitoring and security
tools analysis. The P1GCSSP supports three (3) span mode options utilizing unidirectional solutions
to ensure that traffic cannot be injected back into the network port(s) from any span port.
This document describes the front panel, LED indications, interfaces, rear panel, rear switch settings,
port speed options and installation procedure for the P1GCSSP.
Front Panel
LED Indications
Port A LFP N/A
Port A LNK Link/Activity LED
Port B LFP N/A
Port B LNK Link/Activity LED
Interfaces
Span1 Mode
Port A Network Port (ingress only)
Port B Span Port
Port C Span Port
Port D Span Port
Span2 Mode
Port A Network Port (ingress only)
Port B Network Port (ingress only)
Port C Span Port (aggregate A and B)
Port D Span Port (aggregate A and B)
Span3 Mode
Port A Network Port (ingress only)
Port B Network Port (ingress only)
Port C Network Port (ingress only)
Port D Span Port (aggregate A, B and C)
Garland Technology | 716.242.8500 | www.garlandtechnology.com 1
Copyright © 2022 Garland Technology, LLC. All rights reserved.

User Guide
Data Diode SPAN TAP |P1GCSSP |1.2.58
Rear Panel
Rear Panel Switch Settings
Port A/B
Speed
Switch
1
Switch
2
Switch
3
Span
Mode
Switch
4
Switch
5
Switch
6
Switch
7
Switch
8
1G
Auto Negotiate
Off
Off
Off
Span1
Off
Off
N/A
N/A
N/A
1G
Full Duplex
On
Off
Off
Span2
On
Off
N/A
N/A
N/A
100M
Auto Negotiate
Off
On
Off
Span3
Off
On
N/A
N/A
N/A
100M
Full Duplex
On
On
Off
N/A
N/A
N/A
10M
Auto Negotiate
Off
Off
On
N/A
N/A
N/A
10M
Full Duplex
On
Off
On
N/A
N/A
N/A
* The unit must be power cycled if the switch settings are modified.
* The speed of ports C and D are always 1G.
Port Speeds
The following port speeds are supported in the P1GCSSP:
Port A 10M / 100M / 1G
Port B 10M / 100M / 1G
Port C 1G
Port D 1G
Installation Procedure
1. The P1GCSSP may be installed in any available 1U slot of a network rack and secured with rack
mount screws or in the optional rack mount bracket, sold separately. The optional rack mount
bracket is shown below.
Garland Technology | 716.242.8500 | www.garlandtechnology.com 2
Copyright © 2022 Garland Technology, LLC. All rights reserved.

User Guide
Data Diode SPAN TAP |P1GCSSP |1.2.58
2. Using the DIP switches on the rear panel, set the P1GCSSP to the desired speed and span mode.
This step must be completed prior to powering the unit on. If the speed or mode is modified, the
unit must be power cycled.
3. Insert 1G SFPs into ports 3 and 4.
4. Insert standard Ethernet cables into ports A and B. These ports are Auto MDIX.
5. Connect the power supply to the P1GCSSP and plug it in to an available power source.
Optional Rack Mount Bracket
Garland Technology | 716.242.8500 | www.garlandtechnology.com 3
Copyright © 2022 Garland Technology, LLC. All rights reserved.