Geemarc AMPLIDECT 280 User manual

English
AMPLIDECT 280/285™
AMPLIDE CT285™

Electrical connexion :
The apparatus is designed to operate from a 230V 50Hz supply only. (Classified as
«hazardous voltage» according to EN60950 standard).
The apparatus does not incorporate an integral power on/off switch. To disconnect
the power, either switch off supply at the mains power socket or unplug the AC
adaptor. When installing the apparatus, ensure that the mains power socket is
readily accessible.
Telephone connexion :
Voltages present on the telecommunication network
are classified TNV-3 (Telecommunication Network Voltage) according to the
En60950 standard.
For product support and help visit our website at
telephone + 44 01707 384438
or fax + 44 01707 372529
UGAMPLIDECT280/285 UK_ED03
www.geemarc.com
™

Contents
Prior To Use Basic Functions
Congratulations
Safety Precautions
Unpacking
Phone Layout and Key Function
Key Description
LCD Window Icons Description
Connecting Lines
Installing Batteries
Charging Handset
Using Handset Carrying Clip
Using Headset (optional)
Wall Mounting
Turning Handset On/Off
Making a call
Receiving a call
Muting the Microphone
Amplification function
Ringer Setting
Last Number Redial
CID Book
Torch
key lock
Auto Answer
Selecting a Language
HS Name
Range Alarm
Paging
Dial Mode
Handsfree
Flash Signal
1 14
116
117
318
4
18
719
10 20
11 22
11 24
12 24
13 25
13 25
26
26
27
27
28
14
15
28
GUARANTEE
From the moment your Geemarc product is purchased, Geemarc guarantee it for the period of
one year. During this time, all repairs or replacements (at our option) are free of charge. Should
you experience a problem then contact our helpline or visit our website
at www.geemarc.com.The guarantee does not cover accidents, the presence of liquid,
negligence or breakages to any parts. The product must not be tampered with or taken apart by
anyone who is not an authorised Geemarc representative.The Geemarc guarantee in no way
limits your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE AND MUST BE RETAINED AND
PRODUCED IN THE EVENT OF A WARRANTY CLAIM
Please note: The guarantee applies to the Unite Kingdom only.
DECLARATION
Hereby Geemarc Telecom SA declares that this product is in compliance with the essential
requirements and other relevant provisions of the Radio and Telecommunications Terminal
Equipment Directive 1999/5/EEC and in particular article 3 section 1a, 1b and section 2. The
telephone does not operate if the line current is lower than 18 mA.
The declaration of conformity may be consulted at www.geemarc.com
General information

If you subscribe to a DSL service
Please attach a noise filter (contact your DSL provider) to the telephone line between the
base unit and the telephone line jack in the event of the following:
- Noise is heard during conversations.
- Caller ID features do not function properly.
To single-line
telephone jack
Noise filter
Contents
Advanced Functions
Menu Navigation
Menu Map
Phone Book
One-Touch Memories
BS Settings
HS Settings
Registration
Calling with more than one
Handset
Caller ID on call waiting
29
Feature List
56
29
30
31
35
34
37
42
43
Troubleshooting
58
Answering System Solutions
(AMPLIDECT285™only)
59
Technical Specifications
60
45
TAM Functions
(AMPLIDECT285 only) ™
46
Announcement
Message
TAM Setting
Remote Control
46
49
51
55

Technical Specifications
Frequency Range 1.88~1.90GHz
Channels 120 Duplex channels
Frequency Stability
Carrier Power
Modulation
<250mW
GFSK
< ¡ 50 Khz
Charging time 15 hours
Ambient temperature Normal: 15¡ ~ 35¡, Extreme: 0¡ ~ 40¡
Humidity 0%~90%
Weight (grams) Base: 197; Handset: 117.4
Dimensions (mm) Base: Handset: 124.4 x 114 x 78; 133 x 46 x 19.5
Power Supply Base input: 7.5V, 500mA; Handset input: Ni-MH 1.2V , 600mA x 3
Congratulations
on purchasing our high quality product.
Please read the manual carefully to find out about all features available and how your telephone
functions. In doing so you will get the best out of your new phone.
Safety Precautions
To reduce the risk of electrical shock and injury, please follow these basic safety precautions before
using the phone.
1. Carefully read and observe the instructions in this manual.
2. Follow all warnings marked on the unit.
3. When cleaning, unplug the phone first, then use a damp cloth to wipe. Do not use liquid or aerosol
cleaners.
4. Do not place objects on the line cord that may cause damage.
5. Do not use this phone in wet surroundings or environments where there is a risk of explosion.
6. Avoid spilling of any liquid on the phone.
Prior To Use
Design and specifications are subject to change without notice
1
1
60

56
Answering System Solutions (AMPLIDECT285™ only)
Cannot hear messages, beep, etc.
Adjust announce volume.
The system always plays Announce2.
Answering system memory may be full. Erase some messages.
Incoming messages are incomplete.
Answering system memory is full. Erase some messages.
59
7. Unplug this phone from the wall outlet and refer servicing to qualified service personnel only.
8. Pay attention to the polarity of the batteries, insert the rechargeable batteries in accordance with
polarity symbols (this instruction is found in the installing batteries section.)
9. Never use other ordinary batteries or conventional alkaline batteries. This may not only cause
personal injuries but damage to the unit.
10. Do not mix exhausted batteries with full batteries. Exhausted batteries should not be disposed of
with the usual household waste or in a fire.
11. If you are sure you will not be using the handset over a month, please remove the batteries from
the battery compartment.
12. Use only the power supply indicated in the User's Manual.
13. Keep the phone out of the reach of children.
14. Use the phone only in the described manner.
15. Stop using the phone if it becomes damaged.
2

3
Troubleshooting
Symptom Check & Remedy
No operation Check that the power adapter is properly connected.
Check that the telephone line cord is properly connected.
Check that the handset batteries in full power.
Check that the handset batteries are installed properly.
No dial tone Check that the power adapter is properly connected.
Check that the telephone line cord is properly connected.
Nothing appears
on the display Check that the handset batteries have full power.
Check that the handset is on.
Check that the handset batteries are installed properly.
Handset seems
to have very short
battery life
Caller’s number
is not displayed
Consistently short battery life may indicate that replacement of the batteries is necessary.
Make sure the right batteries are used
Check the charge contacts.
The caller may have withheld their details.
Let the phone ring a couple of times as there may be a delay in receiving the Caller ID information.
Make sure you have subscribed to a Caller ID service via your network provider.
58
Unpacking
Once you have unpacked your phone, make sure that all the parts shown below are available. If any
pieces are missing or broken, please promptly call your dealer.
Line cord*
Adapter*
3 AAA Ni-MH
batteries
User's manual
Handset
Base
*The shape of the plugs can vary according to each country’s specification.
Carrying clip

1 3
2
4 6
5
7 9
8
0
A
B
C
J
K
L
T
U
V
G
H
I
P
Q
R
S
D
E
F
M
N
O
W
X
Y
Z
457
TAM Functions (AMPLIDECT285™only)
Digital Answering System
Natural Sound Voice Prompting, for Week
/Time Stamp and Voice Instructions
Maximum 15 Minutes of Recording Time
which includes Incoming Messages
Digital Volume Control
Toll Saver Function
Multiple Languages
Remote control
Answer on/off selection and
announcement
New message alert
Week date setting
Feature List (continued)
Note:
The caller ID feature is only available if you
subscribe to a Caller Display service from
your network provider.
Phone Layout and Keys Function
Earpiece
Microphone
Left soft key
Dial key
Right soft key
Down key
End key
Left key
Up key
Alph numeric
keys
a
Display
Star key Hash key
Right key
One-touch
Memories
M1 to M4
Visual ringer
Charging contacts
Speaker
Battery
compartment
cover
Carrying clip
Handset

Feature List
1.8GHz DECT technology with GAP
Large 2.0" LCD (128 x 64 dots matrix
display)
Up to 5 handsets for optional for one base
Up to 4 bases for optional for one handset
LCD contrast adjustable
Phonebook with up to 50 groups
10 VIP numbers setting from phonebook
Redial book with up to 10 entries
10 ring tones and volume selectable
(5 levels+off)
Shaker and visual ringer
4 one-touch memory speed dial buttons
Key tone ON/OFF selectable
Full handsfree speakerphone
Internal call
Call transfer
3-way conference call
Receiver/Speaker volume adjustable
Mute
PIN protection
Predialing
Redial, Flash, Pause
DTMF/PULSE dialing mode selectable
FLASH time selectable
Call duration display
Real time clock (set time)
Keypad lock
Multiple languages selectable
Auto answer ON/OFF selectable
Alarm clock include snooze option
Handset Name setting
Backlight on LCD and keypad
Caller ID
FSK and DTMF dual system Caller ID
Caller ID / Call Waiting
Caller ID list with up to 40 entries
Incoming calls can be called back/added
to phonebook/deleted
New call indicator
Message waiting
5
Phone Layout and Keys Function (continued)
Volume Control
Headset Jack
Tone Control
Amplify (AMP)
Button
AMP :Ex tra amp lification on handset up to 15dB
Vol +/- : Adjustabl e volume con trol with the
headset or on handsfree mode
Tone : Ad justable tone control (Hi /Normal/Low)
56

6
Phone Layout and Keys Function (continued)
Base : AMPLIDECT285™
Rear View
Power Jack
Phone Line Jack
Charge pins
Base display
Microphone
Speaker
Remote Control (AMPLIDECT285™ only)
You can access many features of your answering
machine remotely from any touch tone telephone.
A four-digit security code (remote code) is
required to access the system and the factory
default one is 0000. To enter remote access:
1. Dial your telephone number from any touch
tone telephone.
2. When the Announce1/Announce2 starts to
play, you may enter the remote access mode
by inputting the remote code.
3. After you enter the remote code, the system
will play the menu of commands. You can then
follow the commands to operate.
Note:
If you enter the remote code incorrectly the
answering machine will ask you to enter the
code again. You are then given two more
attempts to enter the correct remote code
before the line is disconnected.
Remote access commands
Button Function
Play the main menu
Play the new messages
Play the saved messages
Delete all the messages
Switch the answering machine on/off
Record Announce1/2 (Depends on your
setting)
Note:
You had better stop playing message before
hanging up.
When you press or key to play back the
messages, press to replay current message,
press to stop, press to delete current
message.
After you record the Announce1/Announce2, press
the key or the key to finish. The system
will play the announcement you have recorded.
Announce 1/2
Play/Stop
Previous Message/
Next message
Erase message
Tam On/Off
Speakerphone
setting
Base : AMPLIDECT280™
Paging
Charge pins
Paging
55
53