German pool HTB-716 User manual

在使用之前請詳細閱讀 「使用說明書」及「保用條款」
，並妥為保存。
Please read this user manual instructions and warranty terms & conditions carefully
before use, and keep them handy for future reference.
HTB-716
Multi-Purpose Bathroom Heater
多功能浴室乾衣暖風機
使 用 說 明 書 U S E R M A N U A L

P.2
目錄
注意事項 03
產品結構 04
安裝說明 04
操作說明 10
清潔與保養 11
技術規格 11
保用條款 23

P.3
注意事項
重要說明
為安全起見，使用產品前請先細閱本說明書，並保存說明書，以便作參考之用。
本產品只供家居使用。請必須依照說明書內的指示操作。
安裝和操作之前請認真閱讀本說明，未能遵守本說明可能導致人身傷害或財產損失。
為降低火災，觸電或受傷等風險，遵守以下指示:
1.在製造商的指示下使用該產品，如果你有任何問題，請聯繫製造商或被授權經銷商。
2.安裝工作和電氣接線必須由符合當地法律法規、擁有相關資格的人員進行操作。
3.切割或者鑽入牆壁或天花板的時候，請注意不要損壞電線和其他隱藏的工具。
4.在維修或清潔產品之前，請務必關閉產品的所有功能，並切斷電源，以防止開關意外接通
電源。
5.使用本產品時，請確認產品所標明的使用電壓，是否與接地插座電壓一致，並切勿與其它
電器共用電源插頭。
6.切勿於操作本產品時將手指或外物伸入進出風柵，以免燙傷或造成危險。
7.切勿對進出風柵澆水，以免引起短路或觸電。
8.手濕時切勿接觸進出風柵或操作面板，以免觸電。
9.清潔或更換本產品前，必須先切斷電源。
10.切勿使用任何稀釋劑或任何腐蝕性物質清潔本產品，以免損壞本產品。
11.切勿頻繁開啟或關掉功能鍵，以免影響正常操作，長時間不使用本產品請切斷電源。
12. 本產品不適宜讓兒童、身體或心智殘障、缺乏經驗或知識的人士操作，除非該人士得到負
責保護其安全的人士之監督或指引。
13. 兒童必須被監督，切勿讓兒童使用、觸摸或把玩本產品。
14. 切勿使用受損壞的電線或電源插頭，以防觸電、引起短路或火災。
15. 如電源線損壞或發生其他故障，切勿自行拆卸、修理或改裝，必須由本公司或符合資格的專
業技術人員更換或維修。

P.4
產品結構
機身
裝箱明細及配件
安裝本體前，可能要進行電源的連接工程。當提供的電源線不夠長時，請先將機體從防水箱中取
出，完成電源連接作業。
天花式安裝
1.天花板開孔
在浴室天花板上開口，基本安裝的
開口尺寸：300x300mm。（見圖1）
機體
面罩卡塊
面罩 PTC 陶瓷發熱
防水箱
出風口
產品規格及設計如有變更，恕不另行通知，最新版本請瀏覽www.germanpool.com。
Specications are subject to change without prior notice. Refer to www.germanpool.com for the most up-to-date version.
安裝說明
(圖1)
主機
1
防水箱
1
風格柵
1
風管
(1.5m)
1
互聯軟線
(四芯)
1
開關
(三聯)
1
抱箍
2
電源線
(1.5m)
1
附件
1
說明書
1

P.5
2. 拆除防水箱（見圖2）
（1）打開面罩上的面罩卡塊，卸下固定面罩的2顆自攻螺釘，然後卸下面罩。
（2）卸下固定整個機體的4顆自攻螺釘，將機體小心地從防水箱中拉出。
3. 安裝防水箱
將防水箱用四根螺絲杆穩固吊掛於天花板成水平狀態。（見圖3）
安裝說明
(圖3)
(圖2)

P.6
安裝說明
4.安裝出風口
固定好防水箱之後，將出風口用兩顆螺絲固定在防水箱開孔處。
5.連接風管
將出風口與風管的一端用抱箍或者捆紮帶固定，風管另一端伸展至戶外。如有需要，另一端可
用抱箍或者捆紮帶連接在風格柵上。
6.安裝機體
將機體對準出風口插入防水箱之中，然後用自攻螺釘再將機體固定在防水箱上。
7.安裝面罩
用螺釘將面罩固定在機體上，最後卡入面罩卡塊。
8.固定開關
接通電源之後，按下開關板上的各個功能鍵，確認產品的各項功能正常，然後將開關固定在牆
壁上，固定位置應能有效防止水濺。
掛牆安裝方式
根據不同的安裝空間，合理佈置主機、防水箱以及開關的安裝位置。
1.拆除防水箱（見圖2）
（1）打開面罩上的面罩卡塊，卸下固定面罩的2顆自攻螺釘，然後卸下面罩。
（2）卸下固定整個機體的4顆自攻螺釘，將機體小心地從防水箱中拉出。
2.防水箱鑽孔
在防水箱底部用電鑽打出4個的φ5安裝孔，四個角上各一個。（見圖4）
3.固定防水箱
將防水箱放置於牆上適當高度，出風口向下，根據防水箱上已經鑽出的孔與牆體進行配打，在
牆體上鑽出φ8的孔，將φ4塑膠膨脹敲入牆體上的孔洞之中，再將防水箱固定於牆體之上。
(圖4) (圖5)

P.7
安裝說明
4.安裝出風口
固定好防水箱之後，將出風口用兩顆螺絲固定在防水箱開孔處。（見圖5）
5.安裝機體
將機體對準出風口插入防水箱之中，然後用自攻螺釘再將機體固定在防水箱上。
6.安裝面罩
用螺釘將面罩固定在機體上，最後卡入面罩卡塊。
7.固定風管
將風管插入防水箱的出風口處，用抱箍或捆紮帶固定，風管末端延展至戶外。如有需要，另一
端可用抱箍或者捆紮帶連接在風格柵上。
8.固定開關
接通電源之後，按下開關板上的各個功能鍵，確認產品的各項功能正常，然後將開關固定在牆
壁上，固定位置應能有效防止水濺。
注意:在避免水濺的前提下，盡量將主機安裝在較低位置，便於暖氣流通。
窗式安裝方式
開孔尺寸 35cm
30cm
30cm
2.5cm
2.5cm
18.5cm
18.5cm
2.5cm
2.5cm
35cm
鋁窗框邊
面罩
底視圖
鋁窗連玻璃
不少於35cm
玻璃開孔尺寸為
30cm x 30cm
機身深度為
18.5cm
鋁窗框每邊
預留最少2.5cm
10.9cm
10.9cm
16cm
2.5cm
1.5cm
出風口

P.8
安裝說明
3.固定開關
接通電源之後，按下開關板上的各個功能鍵，確認產品的各項功能正常，然後將開關固定在
牆壁上，固定位置應能有效防止水濺。
注意:在避免水濺的前提下，盡量將主機安裝在較低位置，便於暖氣流通。
根據不同的安裝空間，合理佈置主機、開關的安裝位置。
1.玻璃開孔尺寸：約300mm x 300mm，可按實際情況進行適當調整。
2.將防水箱連同機體一同推入鋁框開孔處，用螺絲將防水箱固定在鋁框上，然後用玻璃膠填充周邊
進行防水處理。（見圖6）
注意:出風口孔洞方向朝下。
(圖6)

P.9
如需要重新接線，請嚴格遵守接線圖進行連接。
接線圖
安裝說明
F1
~
~
P
F2
L
N
E
K
N
L
220V 50Hz
黃綠
藍
棕
黑
黃
白
電源
“電源雙極開關”
規格應不低於
250V~15A
暖風 吹風
換氣
開關（反面）
K：斷路器 F1:吹風 F2：換氣 P: PTC發熱器 θ: 熱保護器
θ
- 本產品安裝應盡量遠離窗簾和其他可燃材料，以避免火災等危險；
- 本產品安裝應避免在浴缸或淋浴區可觸及到開關；
- 通風管應避免與燃氣熱水器排氣管接入同一煙道，以防危險氣體的滲入；
- 接線應由專業電工完成；
- 安裝時電源線必須保持在斷電狀態；
- 請務必使用本產品所配互連軟線及開關等配件安裝；
- 電源線必須能承受10A以上的負載；
- 本產品應可靠接地。
警 告

P.10
操作說明
換氣功能 沒有暖風效果
或
1.「開關」鍵向下按，橙色指示朝上。
2.「吹風」鍵向上按，橙色指示朝下。
注意：換氣過程中，「暖風」功能自動關閉，因此「暖風」按鍵
位置不影響換氣運作。
- 使用過程中絕對不可直接接觸出風口，以免高溫燙傷；
- 如在使用中發現異常情況，應立即斷開電源，通知當地的代理商或特約維修單位的人員前來
處理；
- 使用時請不要頻繁開啟和關斷開關，長時間(6小時或以上)不用應斷開總電源；
- 老人、小孩和行動不便人員應在家人照看和指導下使用本產品。
警 告
原始備用狀態
「開關」向上按，隱藏橙色指示，所有功能關閉。
開關 POWER
吹風 FAN
換氣
VENT
暖風 HEAT
暖風功能 吹出暖風
1.「開關」鍵向下按，橙色指示朝上。
2.「吹風」及「暖風」鍵同時向下按，兩個橙色指示均同時朝上。
注意：必須開啟「吹風」功能方有暖風。
1
2 2
開關 POWER
吹風 FAN
換氣
VENT
暖風 HEAT
吹風功能 室溫吹風
1.「開關」鍵向下按，橙色指示朝上。
2.「吹風」鍵向下按，橙色指示朝上。
注意：必須關掉暖風功能。請把「暖風」鍵向上按以隱藏「暖風」功能的橙色指示。
1
2
開關 POWER
吹風 FAN
換氣
VENT
暖風 HEAT
1
2
開關 POWER
吹風 FAN
換氣
VENT
暖風 HEAT
1
2
開關 POWER
吹風 FAN
換氣
VENT
暖風 HEAT
本產品為家用浴室取暖器，兼有吹風、換氣功能。

P.11
1.清潔前必須斷開電源；
2.清潔時應用浸潤中性清潔劑的軟布輕輕擦拭面罩表面；
3.所有電氣元件不能與水接觸。
注意：不可用汽油或有腐蝕的化學試劑清洗機器的零部件，不能用高於60℃的熱水浸洗塑膠件。
清潔與保養
技術規格
型號 HTB-716
電壓(V) 220 V
頻率(Hz) 50 Hz
功率(W) 1,630 W
主機尺寸 (H) 185mm (W) 270mm (D) 270mm
開孔尺寸 (H) 165mm (W) 300mm (D) 300mm
淨重 3.8 kg
連防水箱淨重 6.2 kg
- 本產品規格及設計如有變更，恕不另行通知。
- 中英文版本如有出入，一概以中文版為準。
- 本產品使用說明書以www.germanpool.com 網上版為最新版本。

P.12
Content
Warning 13
Product Structure 14
Installation Instructions 14
Operating Instructions 21
Care & Maintenance 22
Technical Specications 22
Warranty Terms & Conditions 23

P.13
Warning
Important
For safety purposes, read the instructions carefully before using the appliance. Retain the User
Manual for future reference.
The appliance is designed for domestic use only, and may only be installed and operated in
accordance with this User Manual.
Please read these instructions carefully before attempting to install or operate this product. Failure to
comply with instructions could result in personal injury or property damage.
To reduce the risk of re, electric shock or injury to persons, observe the following:
1. Use this unit only in the manner intended by the manufacturer. If you have any questions, please
contact the manufacturer or authorized distributors.
2. Installation work and electrical wiring must be done by a qualied person(s) in accordance to all
applicable codes and standards.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
4. Before servicing or cleaning this unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switch on accidentally. When the service
disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
5. Before plugging in the appliance, check that the electrical rating shown on the rating label corresponds
with your house’s electricity supply.
6. Do not insert ngers or other objects into the fascia when the appliance is in operation, in order to
avoid burns or danger.
7. Do not spray water on the fascia to avoid short circuit or electric shock.
8. Do not touch the fascia or the control panel with wet hands to avoid electric shock.
9. Always unplug the unit before cleaning or repairing.
10. Do not clean the appliance with thinner or any corrosive materials to avoid damaging the unit.
11. Do not turn on and off the appliance too often to avoid malfunction. Disconnect the power if the
appliance is not in use for a long period of time.
12. The appliance is not intended for use by persons, including children, with reduced physical, sensory
or mental capabilities, or any individual lacking experience and knowledge unless they have been
given supervision or instruction by a person responsible for their safety.
13. Children should be under supervision to ensure that they do not play with the appliance.
14. If the supply cord is damaged or other troubles appear, please contact our Repair Centre or qualied
technicians for help. Do not disassemble, repair, or modify the appliance by yourself.
15. Do not operate the appliance when the power cord or plug is damaged, in order to avoid electric shock,
short circuit, or re hazard.

P.14
Product Structure
Main Unit
Product Content & Accessories
Power connection might be needed before installing the product. When the power cord provided is
not long enough, please remove the machine from the waterproof shell to redo power supply
connection.
Ceiling Mounting
1. Cut hole
Cut a hole on the ceiling, sized about
300mm x 300mm. (Fig.1)
Housing
Fixture Block
Fascia PTC Ceramic Heating
Waterproof Shell
Outlet
Installation Instructions
(Fig.1)
Main Unit
1
Waterproof
Shell
1
Grill
1
Duct
(1.5m)
1
Interconnecting
Cord
1
Switch
1
Duct Hoop
2
Power
Cord(1.5m)
1
Accessories
Pouch
1
User
Manual
1
Specications are subject to change without prior notice.

P.15
2. Remove waterproof shell (Fig. 2)
(1) Remove the xture block from the fascia carefully. Unx the two screws on the fascia, and
remove the fascia from the housing.
(2) Unx the four screws of the waterproof shell, and remove it from the main unit.
3. Install waterproof shell
Use 4 long bolts to x the waterproof shell on the ceiling, keep it rmly hangs on the ceiling steadily
and levelly. (Fig. 3)
Installation Instructions
(Fig.2)
(Fig.3)

P.16
Installation Instructions
4. Install outlet
Install the outlet with 2 screws on the waterproof shell.
5. Connect duct
Insert the ventilation duct into the outlet duct; x them with a hoop or cable tie. If necessary, the
other end could be connected to the air grille and also x with the hoop or a cable tie.
6. Mount unit
Put the housing into the waterproof shell, make sure the slot is on the right place and could
install on the outlet. Fix the housing to the waterproof shell with screws.
7. Install facial plate
Return the fascia to the housing and x it with screws, and return the xture block to the fascia.
8. Fix Switch
After turning on the power supply, press the switches to make sure every function works. Then,
x the switch on the wall. The xed position should be where water splashes can be avoided.
Note:
- The switch should not be installed in an area directly accessible from the bathtub or shower.
Wall Mounting
For different installation site, arrange the mounting position of the machine and switch accordingly.
1. Remove waterproof shell (Fig. 2)
(1) Remove the xture block from the fascia carefully. Unx the two screws on the fascia, and
remove the fascia from the housing.
(2) Unx the four screws of the waterproof shell, and remove it from the housing.
2. Drill waterproof shell
Using an electric drill, drills four holes on the bottom of the waterproof shell, sized Ø5. Four
holes should be on each corner. (Fig. 4)
3. Install waterproof shell
Put the waterproof shell with outlet on appropriate height on the wall; make sure the outlet is on
the downside. According to the holes drilled on the waterproof shell drill four Ø8 holes on the
wall, knock Ø4 plastic expansion screws into the wall, then x the waterproof shell on the wall
with screws.

P.17
Installation Instructions
4. Mount the outlet
Fix the outlet with 2 screws into the holes of the waterproof shell. (Fig. 5)
5. Mount the housing
Put the unit into the waterproof shell, make sure the slot is on the right place and could install on
the outlet. Fix the unit to the waterproof shell with screws.
6. Install the fascia
Return the fascia to housing and x it with screws, and return the xture block to the fascia.
7. Connet duct
Connect one end of the duct (100mm in diameter) to the outlet; x it with a hoop or cable tie.
And then extend the duct to the outdoors through the window. If necessary, the outdoor end could
be connect to the grill by a hoop or cable tie and then x the grill on the wall outside.
8. Fix Switch
After turning on the power supply, press the switches to make sure every function works. Then, x
the switch on the wall. The xed position should be where water splashes can be avoided.
Note:
On the premise of avoiding water splashes, install the machine in a position as low as possible to
allow an easy ow of hot air.
(Fig.4) (Fig.5)

P.18
Installation Instructions
Window Mounting
Window Opening Cut-Out Dimensions
35cm
30cm
30cm
2.5cm
2.5cm
18.5cm
18.5cm
2.5cm
2.5cm
35cm
10.9cm
10.9cm
16cm
2.5cm
Depth of machine:
18.5cm
Minimum width
(incl. window opening & frame)
not less than 35cm
Window opening:
30cmx30cm
Reserve 2.5cm on
each side of the frame
Aluminium
Frame Fascia
Air Outlet
Bottom View
1.5cm

P.19
3. Fix Switch
After turning on the power supply, press the switches to make sure every function works. Then, x
the switch on the wall. The xed position should be where water splashes can be avoided.
Note:
On the premise of avoiding water splashes, install the machine in a position as low as possible to
allow an easy ow of hot air.
Installation Instructions
1. The opening of the window should be around 300mm x 300mm. Adjust this reserved size
according to the actual situation as necessary.
2. Push the waterproof shell together with the machine into the reserved hole. Fix the waterproof
shell with screws on the aluminum frame. And then use glass glue lling to seal. (Fig. 6)
Note: Make sure the outlet hole faces downward.
(Fig. 6)

P.20
Wiring
If the rewiring is needed, please make sure you connect the wires exactly the same as the wiring
diagram below.
Installation Instructions
F1
θ
~
P
F2
L
N
E
K
N
L
220V 50Hz
Power
Heat Fan
Vent
K: Breaker F1: Fan F2：Vent P: PTC θ: Thermal Protector
Double-pole
Switch specification
should not be lower
than 250V~15A
Yellow Green
Blue
Brown
Black
Yellow
White
~
Switch (reverse side)
- This unit must be properly grounded.
- A new power cord should be used when to install this unit, the new power cord must stand a
minimum of 10A load.
- The power cord must be supplied with a circuit breaker which should have a minimum of 3mm
off-contact distance.
- Make sure that all electrical connections on the terminal block must be the effective connections,
since poor connections may produce the electrical sparks to cause a re during the long time of
operations. The installing person(s) should check all electrical connections, x or re-x rmly all the
screws on the terminal block to guarantee that all wiring connections are effective connections,
either made at factory or at site/home.
- This unit should not be installed near the curtains or other ammable materials, to avoid any risk
of re.
Warning