Gestetner F540 Owner's manual

Operating Instructions
Advanced Features
For safe and correct use of this machine, please be sure to read the Safety Information in the Basic Features before you use it.
Transmission Options
Communication Information
Other Transmission Features
Reception Features
Copying
Facsimile User Tools
Key Operator Settings
Solving Operation Problems
Maintaining Your Machine
Appendix
StellaF25_EN_Combine_F_pre_FM.book Page 1 Thursday, August 26, 2004 8:45 PM

Introduction
This manual describes detailed instructions on the operation and notes about the use of this machine.
To get maximum versatility from this machine, all operators are requested to read this manual carefully
and follow the instructions. Please keep this manual in a handy place near the machine.
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.
Machine Types
The model names of the machine do not appear in the following pages. Check the type of your machine
before reading this manual.
• Type1: NIC FAX Unit optional
• Type2: NIC FAX Unit standard
Power Source:
120V, 60Hz
Please be sure to connect the power cord to a power source as above. For details about the power
source, see Chapter 10, “Connecting the Power and Switching On” in the Advanced Features manual.
StellaF25_EN_Combine_F_pre_FM.book Page 1 Thursday, August 26, 2004 8:45 PM

i
TABLE OF CONTENTS
How to Read This Manual .....................................................................................1
Paper Mark.................................................................................................................2
Manuals for This Machine .....................................................................................3
Advanced Features (this manual) ..............................................................................3
Basic Features ...........................................................................................................3
Before You Use This Machine ...................................................................................3
NIC FAX Unit Manual (on CD-ROM)..........................................................................3
NIC FAX Unit CD-ROM Manual .................................................................................3
1. Transmission Options
Sending at a Specific Time (Send Later) .............................................................5
Sending Confidential Messages...........................................................................7
User Code Transmission.......................................................................................9
SUB Code Transmission.....................................................................................11
SEP Code Polling Reception ..............................................................................12
Polling Reception.................................................................................................13
File Reserve Report (Polling Reception)..................................................................14
Communication Result Report (Polling Reception)..................................................15
Polling Transmission...........................................................................................16
Polling Transmission Clear Report...........................................................................18
Reduced Image Transmission ............................................................................19
Transfer Request .................................................................................................20
Specifying an End Receiver.....................................................................................22
Fax Header Print ..................................................................................................23
2. Communication Information
Canceling a Transmission or Reception ........................................................... 25
Printing a List of Files in Memory (Print TX File List).......................................26
Changing Transmission Files.............................................................................27
Deleting a Destination ..............................................................................................27
Changing a Destination............................................................................................28
Adding a Destination ................................................................................................28
Changing the Transmission Time ............................................................................29
Starting Transmission Now (Send Next) ..................................................................29
Retrying a Failed Transmission..........................................................................31
Resending a File ......................................................................................................31
Deleting a Destination ..............................................................................................31
Changing a Destination............................................................................................32
Adding a Destination ................................................................................................33
Checking the Transmission Result (TX Status)................................................34
Checking the Reception Result (RX Status)......................................................35
Printing a Stored Message (Print TX File) .........................................................36
Printing a Confidential Message ........................................................................37
Confidential File Report............................................................................................37
StellaF25_EN_Combine_F_pre_FM.book Page i Thursday, August 26, 2004 8:45 PM

ii
Printing a Memory-locked Message................................................................... 38
Printing the Journal ............................................................................................. 39
Printing the Journal ..................................................................................................40
Printing Personal Box Messages .......................................................................42
3. Other Transmission Features
Handy Dialing Functions.....................................................................................43
Chain Dial.................................................................................................................43
Telephone Directory.................................................................................................43
Redial .......................................................................................................................44
SUB/SID (SUB Code Transmission) ........................................................................45
SEP/PWD (SEP Code Polling Transmission) ..........................................................46
On Hook Dial ........................................................................................................48
Manual Dial ...........................................................................................................49
Selecting the Line ................................................................................................50
How to Select the Line .............................................................................................51
Transmission Features........................................................................................52
Stamp.......................................................................................................................52
ID Transmission .......................................................................................................52
Duplex Original Settings...........................................................................................52
If the number of back pages and front pages are different....................................53
Batch Original Documents Transmission .................................................................54
If memory runs out while scanning is in progress..................................................55
Label Insertion..........................................................................................................55
Inserting a label using Auto Document..................................................................56
Auto Document ........................................................................................................57
No Document, No Dial .............................................................................................58
Blank Sheet Detect ..................................................................................................58
Scanner Cleaning Message .....................................................................................58
Backup File Transmission ........................................................................................59
JBIG Transmission...................................................................................................59
More Transmission Functions............................................................................60
If Memory Runs Out While Scanning Is in Progress ................................................60
Checking the Transmission Result...........................................................................60
Broadcasting Sequence ...........................................................................................61
Simultaneous Broadcast ..........................................................................................61
Sending a Fax Message Immediately ......................................................................61
Broadcasting: Checking Progress............................................................................61
Automatic Redial ......................................................................................................62
Batch Transmission..................................................................................................62
Dual Access .............................................................................................................62
ECM (Error Correction Mode) ..................................................................................62
Parallel Memory Transmission.................................................................................62
Printed Reports....................................................................................................64
File Reserve Report (Memory Transmission) ..........................................................64
Communication Result Report (Memory Transmission) ..........................................64
Communication Failure Report ................................................................................65
Transmission Result Report (Immediate Transmission) .........................................65
StellaF25_EN_Combine_F_pre_FM.book Page ii Thursday, August 26, 2004 8:45 PM

iii
4. Reception Features
General..................................................................................................................67
Immediate Reception ...............................................................................................67
Memory Reception ...................................................................................................68
Substitute Reception ................................................................................................69
Screening out messages from anonymous senders .............................................70
Reception Functions ...........................................................................................71
Transfer Station........................................................................................................71
Transfer Result Report ..........................................................................................72
Remote Transfer ......................................................................................................72
How to make a Remote Transfer Request (push signal).......................................72
ID Reception ............................................................................................................74
JBIG Reception ........................................................................................................74
Printing Functions ...............................................................................................75
Center Mark .............................................................................................................75
Checkered Mark.......................................................................................................75
Multi-copy Reception................................................................................................75
Two-sided Reception ...............................................................................................76
Reception Time ........................................................................................................76
Two in One...............................................................................................................76
Page Separation and Length Reduction ..................................................................77
TSI Print ...................................................................................................................77
Adjusting the Printing Density ..................................................................................78
Toner saving..........................................................................................................78
When There Is No Paper of the Correct Size.....................................................79
5. Copying
Copying.................................................................................................................81
Making Copies on Special Paper .............................................................................82
Making Two-sided Copies........................................................................................83
One-sided to two-sided..........................................................................................84
Two-sided to two-sided..........................................................................................85
Two-sided to one-sided .........................................................................................86
6. Facsimile User Tools
User Tools Menu..................................................................................................89
Counters...................................................................................................................93
Selecting the Display Language...............................................................................94
Program/Delete Menu..........................................................................................95
Programs..................................................................................................................95
Storing a Program .................................................................................................95
Changing the Program name ................................................................................96
Using a Program....................................................................................................96
Deleting a Program ...............................................................................................96
Auto Documents.......................................................................................................97
Programming/changing .........................................................................................97
Printing the Auto Document original......................................................................99
Deleting ...............................................................................................................100
StellaF25_EN_Combine_F_pre_FM.book Page iii Thursday, August 26, 2004 8:45 PM

iv
User Function Keys................................................................................................101
Programming/changing the contents of a User Function key..............................103
Using a User Function key ..................................................................................104
Deleting functions stored in User Function keys .................................................104
Reports/Lists ......................................................................................................105
Setup ...................................................................................................................107
Adjusting the Display Contrast ...............................................................................107
Date/Time...............................................................................................................107
Tray Paper Size .....................................................................................................108
Paper Tray for Two-sided Printing .........................................................................109
Bypass Paper Type................................................................................................110
Auto Reset Timer ...................................................................................................111
On Hook Timeout ...................................................................................................112
7. Key Operator Settings
Key Operator Tools Menu .................................................................................113
Using Key Operator Settings ............................................................................116
Resetting the ADF Counter ....................................................................................116
Authorized Reception.............................................................................................116
Memory Lock..........................................................................................................119
Multi-copy Reception..............................................................................................121
Specified Tray ........................................................................................................123
Two-sided Reception .............................................................................................126
Remarks on Two-sided Reception ......................................................................128
Forwarding .............................................................................................................129
Backup File Transmission Settings ........................................................................133
Economy Transmission..........................................................................................135
Energy Save Timer ................................................................................................136
User Parameters ....................................................................................................138
How to set the User Parameters .........................................................................147
ID Codes ................................................................................................................148
Programming.......................................................................................................149
G3 Analog Line ......................................................................................................150
Transfer Report ......................................................................................................152
File Retention .........................................................................................................153
Network Settings ....................................................................................................154
IP-Fax Parameter Settings.....................................................................................154
Key Layout .............................................................................................................154
Memory File Transfer .............................................................................................155
Print Position ..........................................................................................................156
RDS (Remote Diagnostic System).........................................................................157
System Parameter Transmission ...........................................................................158
Box Settings ...........................................................................................................159
Personal Boxes ...................................................................................................160
Programming/changing Personal Boxes .............................................................160
Deleting Personal Boxes .....................................................................................162
Transfer Boxes ....................................................................................................163
Programming/changing Transfer Boxes ..............................................................164
Deleting Transfer Boxes ......................................................................................166
Printing the Box List.............................................................................................167
StellaF25_EN_Combine_F_pre_FM.book Page iv Thursday, August 26, 2004 8:45 PM

v
8. Solving Operation Problems
Clearing a Paper Jam in the Optional Paper Tray Unit...................................169
Reading Reports ................................................................................................170
Error Report ...........................................................................................................170
Power Failure Report .............................................................................................170
Error Codes ........................................................................................................171
9. Maintaining Your Machine
Loading Paper in the Optional Paper Tray Unit ..............................................173
Loading Paper in the Bypass Tray ...................................................................174
Changing the Paper Size...................................................................................176
Changing the Paper Size in the Main Paper Tray..................................................176
Changing the Paper Size in the Optional Paper Tray Unit.....................................177
Cleaning the Scanner ........................................................................................179
Replacing the ADF Maintenance Kit ................................................................180
Replacing the Photo Conductor Unit (PCU) .................................................... 181
Replacing the Stamp Cartridge ........................................................................184
10.Appendix
Installing, Moving, and Disposing of the Machine..........................................187
Machine Environment ............................................................................................187
Location..................................................................................................................189
Connecting the Power and Switching On...............................................................190
Moving the Machine ...............................................................................................191
Disposing of the Machine.......................................................................................191
Connecting to a Telephone Line ......................................................................192
Connecting the Machine to the Telephone Line.....................................................192
Connecting to an Additional G3 Line......................................................................192
Connecting an External Telephone........................................................................192
Supplies ..............................................................................................................193
Options ...............................................................................................................194
40MB Memory Card ...............................................................................................194
Extra G3 Interface Unit...........................................................................................194
Handset..................................................................................................................194
NIC FAX Unit (Option for Type1) ...........................................................................195
Printer Interface Unit ..............................................................................................195
Paper Tray Unit ......................................................................................................196
Bypass Tray Unit (Option for Type1)......................................................................196
Specifications.....................................................................................................197
Acceptable Types of Originals ...............................................................................199
Acceptable original sizes .....................................................................................199
Paper size and scanned area..............................................................................199
Paper......................................................................................................................200
Recommended paper sizes and types ................................................................200
Non-recommended paper....................................................................................201
StellaF25_EN_Combine_F_pre_FM.book Page v Thursday, August 26, 2004 8:45 PM

vi
Energy Saving........................................................................................................201
Introduction..........................................................................................................201
Entering Energy Saver Mode ..............................................................................202
Exiting Energy Saver Mode .................................................................................203
Selecting the Energy Saver Mode type ...............................................................203
Reception in Energy Saver Mode........................................................................203
Maximum Values................................................................................................204
INDEX....................................................................................................... 205
StellaF25_EN_Combine_F_pre_FM.book Page vi Thursday, August 26, 2004 8:45 PM

1
How to Read This Manual
The following set of symbols is used in this manual.
R
WARNING:
This symbol indicates a potentially hazardous situation that might result in
death or serious injury when you misuse the machine without following the in-
structions under this symbol. Be sure to read the instructions, all of which are de-
scribed in the Safety Information section in the Basic Features manual.
R
CAUTION:
This symbol indicates a potentially hazardous situation that might result in mi-
nor or moderate injury or property damage that does not involve personal injury
when you misuse the machine without following the instructions under this
symbol. Be sure to read the instructions, all of which are described in the Safety
Information section in the Basic Features manual.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might be misfed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates information or preparations required prior to operating.
Note
This symbol indicates precautions for operation, or actions to take after abnor-
mal operation.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
{}
Keys built into the control panel of the machine.
StellaF25_EN_Combine_F_pre_FM.book Page 1 Thursday, August 26, 2004 8:45 PM

2
Paper Mark
Paper directions in this book are shown as follows.
Portrait direction for originals is shown as K, and landscape direction for orig-
inals is shown as L.
Portrait direction for paper in the paper tray is shown as K, and landscape di-
rection for paper in the paper tray is shown as L.
Note
❒represents originals or paper.
Reference
For details about the Auto Document Feeder (ADF), see p.18 “Guide to Com-
ponents”, Basic Features.
GFKAMI0N
StellaF25_EN_Combine_F_pre_FM.book Page 2 Thursday, August 26, 2004 8:45 PM

3
Manuals for This Machine
Advanced Features (this manual)
The Advanced Features manual describes more advanced functions and also ex-
plains settings for key operators.
Basic Features
The Basic Features manual explains the most frequently used fax functions and
operations.
Before You Use This Machine
The Before You Use This Machine manual explains how to set up your machine.
NIC FAX Unit Manual (on CD-ROM)
The NIC Fax Unit manual explains about the Scanner function, Internet Fax
function, IP-Fax function, and LAN FAX function.
Note
❒NIC FAX unit is an option for Type1.
NIC FAX Unit CD-ROM Manual
Introduces the contents of the NIC FAX CD-ROM and the necessary operating
environment for the CD-ROM. How to access the NIC FAX unit manual in PDF
file on the CD-ROM is also explained.
Note
❒NIC FAX unit is an option for Type1.
Instructions for the optional and the Extra G3 Interface Unit (G3 Interface Unit Type410) are in-
cluded in the Basic Features and Advanced Features manuals.
StellaF25_EN_Combine_F_pre_FM.book Page 3 Thursday, August 26, 2004 8:45 PM

4
StellaF25_EN_Combine_F_pre_FM.book Page 4 Thursday, August 26, 2004 8:45 PM

5
1. Transmission Options
Sending at a Specific Time (Send Later)
Using the Send Later function, you
can delay transmission of your fax
message until a specified time. This
allows you to take advantage of off-
peak telephone line charges without
having to be by the machine at the
time of transmission.
Important
❒If the power is turned off for 12
hours or longer, all documents
stored in memory are deleted.
Note
❒You cannot specify a time more
than 24 hours into the future.
❒Make sure that the current time
shown in the display is correct be-
fore performing the following pro-
cedure. If it is not correct, you need
to adjust it beforehand. See p.107
“Date/Time”.
❒If you want to use Economy Trans-
mission, program the time when
your phone charges get cheaper.
See p.135 “Economy Transmis-
sion”.
❒
You can assign the Economy Trans-
mission
function to a User Func-
tion key. See p.101 “User Function
Keys”. When you press the User
Function key with this function
programmed in, proceed to step G
in the following procedure.
A
AA
APlace your original, and then se-
lect any scan settings you require.
B
BB
BPress the {
{{
{Trans. Option}
}}
}key.
Confirm that " 1. Send Later " is
displayed.
C
CC
CPress the {
{{
{OK}
}}
}key.
D
DD
DPress 0
00
0or 1
11
1to select "On".
E
EE
EPress the {
{{
{OK}
}}
}key.
Specifying a time
AConfirm that “Option” is se-
lected.
BPress the {
{{
{OK}
}}
}key.
CPress 0
00
0or 1
11
1to select “AM” or
“PM”.
DPress the {
{{
{OK}
}}
}key.
GFTIME0N
Transmitter
Send Later
at 21:00(9:00PM)
Receiver
StellaF25_EN_Combine_F_pre_FM.book Page 5 Thursday, August 26, 2004 8:45 PM

Transmission Options
6
1
EEnter the time that you want to
send the fax message with the
number keys.
Note
❒You can enter any time be-
tween 1:00 and 12:59.
❒If you make a mistake, press
the {
{{
{Clear/Stop}
}}
}key and try
again.
❒To cancel Send Later, press
the {
{{
{Cancel}
}}
}key and the dis-
play in step Breappears.
Sending at Economy
Transmission Time
APress 0
00
0or 1
11
1to select "Econo-
my TX".
BPress the {
{{
{OK}
}}
}key.
CPress 0
00
0or 1
11
1to select “AM”or
“PM”according to your setting
for Economy Transmission
Time.
DPress the {
{{
{OK}
}}
}key.
The programmed Economy
Transmission Time is dis-
played.
Note
❒To cancel Send Later, press
the {
{{
{Cancel}
}}
}key and the dis-
play in step Breappears.
F
FF
FPress the {
{{
{OK}
}}
}key.
G
GG
GSpecify the destination.
H
HH
HPress the {
{{
{Start}
}}
}key.
Note
❒To cancel an Immediate Trans-
mission set up for Send Later,
remove the original. To cancel a
Memory Transmission set up
for Send Later, see p.25 “Cancel-
ing a Transmission or Recep-
tion”.
StellaF25_EN_Combine_F_pre_FM.book Page 6 Thursday, August 26, 2004 8:45 PM

Sending Confidential Messages
7
1
Sending Confidential Messages
This feature is called Confidential
Transmission. Use this feature if you
do not want your message to be
picked up casually by anybody at the
other end. The message will be stored
in the memory at the other end. It will
not be printed until the Confidential
ID is entered.
There are two types of Confidential
Transmission:
❖
❖❖
❖Default ID
The other party can print the mes-
sage by entering the ID that was
previously stored in the other par-
ty's terminal using the Confiden-
tial ID feature.
❖
❖❖
❖ID Override
If you want to send a confidential
message to a particular person at
the other end, you can specify the
Confidential ID that person has to
enter to see that message. Any-
body entering the machine's Confi-
dential ID will not be able to see
the message. Before you send the
message, do not forget to tell the
intended receiver what code must
be entered to print the message.
Limitation
❒The destination machine must be
of the same make and have the
Confidential Reception feature.
Note
❒We recommend that you program
the Confidential ID beforehand.
See p.148 “ID Codes”.
❒An ID can be any 4-digit number
except 0000.
❒
The destination machine must have
enough memory available.
A
AA
APlace your original, and then se-
lect any scan settings you require.
B
BB
BPress the {
{{
{Trans. Option}
}}
}key.
C
CC
CPress 0
00
0or 1
11
1until "2. Confiden-
tial TX" is displayed.
D
DD
DPress the {
{{
{OK}
}}
}key.
E
EE
EPress 0
00
0or 1
11
1to select "On".
F
FF
FPress the {
{{
{OK}
}}
}key.
G
GG
GSelect the type of Confidential
Transmission.
Normal Confidential
Transmission
AConfirm that “Default”is se-
lected.
GFSINS0N
Transmitter
Receiver
Entering the Confidential ID
StellaF25_EN_Combine_F_pre_FM.book Page 7 Thursday, August 26, 2004 8:45 PM

Transmission Options
8
1
Note
❒To cancel the Confidential
Transmission, press the {
{{
{Can-
cel}
}}
}key and the display in
step Creappears.
BPress the {
{{
{OK}
}}
}key.
Confidential ID Override Option
APress 0
00
0or 1
11
1to select "Over-
ride".
BPress the {
{{
{OK}
}}
}key.
CEnter the Confidential ID (4
digits) with the number keys.
Note
❒To cancel the Confidential
Transmission, press the {
{{
{Can-
cel}
}}
}key and the display in
step Creappears.
DPress the {
{{
{OK}
}}
}key.
H
HH
HSpecify the destination.
I
II
IPress the {
{{
{Start}
}}
}key.
Note
❒To cancel an Immediate Trans-
mission set up for Confidential
Transmission, remove the origi-
nal. To cancel a Memory Trans-
mission set up for Confidential
Transmission, see p.25 “Cancel-
ing a Transmission or Recep-
tion”.
-
--
-Sending Confidential
Messages to Other Makers'
Machines
Confidential Transmission is only
possible with machines of the same
make that have the Confidential
Transmission feature. However, if
you use the SUB/SID function, you
can send confidential fax messages to
and receive confidential fax messages
from other makers' machines that
have the SUB/SID feature. See p.11
“SUB Code Transmission”.
StellaF25_EN_Combine_F_pre_FM.book Page 8 Thursday, August 26, 2004 8:45 PM

User Code Transmission
9
1
User Code Transmission
User codes allow you to keep track of
machine usage. If everyone uses a
user code when they use the fax ma-
chine, the codes or the names pro-
grammed for the codes will be
printed in the Journal and other re-
ports. This will help you to check who
has been using the machine and how
often.
Preparation
To program user codes, create a
Personal Box for each user before-
hand. The SUB code you specify
will become the user's user code.
See p.160 “Programming/chang-
ing Personal Boxes”.
Note
❒User names (the name of the Per-
sonal Box) can be printed on faxes,
lists, or reports printed at the other
end.
❒When a user name is programmed
with a user code, and a fax mes-
sage is sent with the Label Inser-
tion function assigned to either a
Quick Dial key or Speed Dial set to
on, you can have the receiver name
which is programmed in a Quick
Dial key or Speed Dial and the user
name printed on the message
when it is received at the other
end. See p.55 “Label Insertion”.
❒Instead of the Fax Header, you can
choose the user name (the name of
the Personal Box) to be printed at
the same position on the message.
You can turn this function on or off
with the User Parameters. See
p.138 “User Parameters”(switch
20, bit 5).
❒
You can assign the User Code Trans-
mission
function to a User Func-
tion key. See p.101 “User Function
Keys”. When you press the User
Function key with this function
programmed in, proceed to step G
in the following procedure.
A
AA
APlace your original, and then se-
lect any scan settings you require.
B
BB
BPress the {
{{
{Trans. Option}
}}
}key.
C
CC
CPress 0
00
0or 1
11
1until "3. User Code"
is displayed.
D
DD
DPress the {
{{
{OK}
}}
}key.
E
EE
EPress 0
00
0or 1
11
1to select "On".
F
FF
FPress the {
{{
{OK}
}}
}key.
G
GG
GEnter a user code/SUB code (up to
20 characters) with the number
keys.
Note
❒If you incorrectly enter the code,
press the {
{{
{Clear/Stop}
}}
}key and
try again.
❒To cancel the User Code Trans-
mission, press the {
{{
{Cancel}
}}
}key
and the display in step Creap-
pears.
StellaF25_EN_Combine_F_pre_FM.book Page 9 Thursday, August 26, 2004 8:45 PM

Transmission Options
10
1
H
HH
HPress the {
{{
{OK}
}}
}key.
Note
❒The programmed user name is
displayed for two seconds.
❒When an unprogrammed user
code is entered, the message
“The Code Entered is not
Programmed”appears. Then the
display in step Greappears.
I
II
ISpecify the destination.
J
JJ
JPress the {
{{
{Start}
}}
}key.
Note
❒To cancel an Immediate Trans-
mission set up for User Code
Transmission, remove the origi-
nal. To cancel a Memory Trans-
mission set up for User Code
Transmission, see p.25 “Cancel-
ing a Transmission or Recep-
tion”.
StellaF25_EN_Combine_F_pre_FM.book Page 10 Thursday, August 26, 2004 8:45 PM

SUB Code Transmission
11
1
SUB Code Transmission
Confidential Transmission is only
possible with machines of the same
make that have the Confidential
Transmission feature. However, if
you use the SUB/SID function, you
can send confidential fax messages to
and receive confidential fax messages
from other makers' machines that
have the SUB/SID feature.
This feature is used when sending
faxes to other parties' Personal Boxes
or Transfer Boxes.
Reference
p.45 “SUB/SID (SUB Code Trans-
mission)”
p.160 “Personal Boxes”
p.163 “Transfer Boxes”
A
AA
APlace your original, and then se-
lect any scan settings you require.
B
BB
BPress the {
{{
{Trans. Option}
}}
}key.
C
CC
CPress 0
00
0or 1
11
1until "4. TX with
SUB" is displayed.
D
DD
DPress the {
{{
{OK}
}}
}key.
E
EE
EPress 0
00
0or 1
11
1to select "On".
F
FF
FPress the {
{{
{OK}
}}
}key.
G
GG
GSpecify the destination.
H
HH
HPress the {
{{
{OK}
}}
}key.
I
II
IEnter the SUB code (up to 20 char-
acters).
Note
❒You can enter digits 0–9, #, *,
and spaces (the first character
cannot be a space).
❒If you incorrectly enter the code,
press the {
{{
{Clear/Stop}
}}
}key and
try again.
J
JJ
JPress the {
{{
{OK}
}}
}key.
If you do not add a destination,
confirm that “No”is selected, and
then proceed to step M.
K
KK
KPress 0
00
0or 1
11
1to select "Yes".
L
LL
LPress the {
{{
{OK}
}}
}key.
Repeat steps Gto Kfor all destina-
tions you want to specify.
M
MM
MPress the {
{{
{OK}
}}
}key.
N
NN
NPress the {
{{
{Start}
}}
}key.
Note
❒To cancel an Immediate Trans-
mission set up for SUB Code
Transmission, remove the origi-
nal. To cancel a Memory Trans-
mission set up for SUB Code
Transmission, see p.25 “Cancel-
ing a Transmission or Recep-
tion”.
StellaF25_EN_Combine_F_pre_FM.book Page 11 Thursday, August 26, 2004 8:45 PM

Transmission Options
12
1
SEP Code Polling Reception
If you want to receive a message
stored in the memory of another par-
ty's fax machine, use this feature.
Your machine will receive the mes-
sage with the SEP and PWD code that
matches the SEP and PWD code you
enter in the procedure below.
Reference
p.46 “SEP/PWD (SEP Code Poll-
ing Transmission)”
p.16 “Polling Transmission”
A
AA
APress the {
{{
{Trans. Option}
}}
}key.
B
BB
BPress 0
00
0or 1
11
1until "5. RX with
SEP" is displayed.
C
CC
CPress the {
{{
{OK}
}}
}key.
D
DD
DPress 0
00
0or 1
11
1to select "On".
E
EE
EPress the {
{{
{OK}
}}
}key.
F
FF
FSpecify the destination.
Note
❒If you make a mistake, press the
{
{{
{Clear/Stop}
}}
}key and try again.
G
GG
GPress the {
{{
{OK}
}}
}key.
H
HH
HEnter the SEP code (up to 20 char-
acters).
Note
❒You can enter digits 0-9, #, *,
and spaces (the first character
cannot be a space).
❒If you incorrectly enter the code,
press the {
{{
{Clear/Stop}
}}
}key and
try again.
I
II
IPress the {
{{
{OK}
}}
}key.
If you do not add a destination,
confirm that “No”is selected, and
then proceed to step L.
J
JJ
JPress 0
00
0or 1
11
1to select "Yes".
K
KK
KPress the {
{{
{OK}
}}
}key.
Repeat steps Fto Jfor all destina-
tions you want to specify.
L
LL
LPress the {
{{
{OK}
}}
}key.
M
MM
MPress the {
{{
{Start}
}}
}key.
Note
❒
You can cancel SEP Code Polling
Reception. See p.25 “Canceling
a Transmission or Reception”.
StellaF25_EN_Combine_F_pre_FM.book Page 12 Thursday, August 26, 2004 8:45 PM