Gevi GECMD627BK-U User manual

COFFEE MAKER
INSTRUCTION MANUAL
[email protected]
GECMD627BK-U

IMPORTANT SAFEGUARDS
Read all instructions.
Before using check that the voltage of wall outlet
corresponds to rated voltage marked on the rating plate.
This appliance has been incorporated with a grounded
plug. Please ensure the wall outlet in your house is well
earthed.
To protect against fire, electric shock and injury to persons
do not immerse cord, plug in water or other liquid.
Remove plug from wall outlet before cleaning and when
not in use. Allow appliance cool down completely before
taking off, attaching components or before cleaning.
Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions, or is dropped or
damaged in any manner. Return appliance to the nearest
authorized service facility for examination, repair or
electrical or mechanical adjustment.
The use of accessory attachments not recommended by the
appliance manufacturer may result in fire, electric shock or
injury to persons.
1.
2.
3.
4.
5.
6.
7.
Before using the electrical appliance, the following basic
precautions should always be followed including the
following:
Dear Gevi customer
Gevi have focused on creating perfect home appliance for
our customer. In the past years, it took us time, lots of
research and many prototypes to achieve our goal. We
would like to give you a perfect using experience.
Thanks for purchasing our Gevi products. If have any
questions for our products , please kindly contact our Gevi
service team via email: [e-mail].

SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY
NOTES ON THE CORD PLUG
NOTES ON THE CORD
Place appliance on flat surface or table, do not hang power
cord over the edge of table or counter.
Ensure the power cord do not touch hot surface of
appliance.
Do not place the coffee maker on hot surface or beside fire
in order to avoid to be damaged.
To disconnect, remove plug from wall outlet. Always hold
the plug. But never pull the cord.
Do not use appliance for other than intended use and place
it in a dry environment.
Close supervision is necessary when your appliance is being
used near children.
Be careful not to get burned by the steam.
Do not touch the hot surface of appliance (such as steam
wand, and the steel mesh just boiling). Use handle or knobs.
Do not let the coffee maker operate without water.
Do not remove the metal funnel when appliance in brewing
coffee or when steam.
Connect plug to wall outlet before using and turn any
switch off before plug is removed from wall outlet.
This appliance is not intended for used by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
unless they have been given supervision or instruction
concerning use of the appliances by a person responsible
for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
This appliance has a polarized plug, To reduce the risk of
electric shock, this plug is intended to fit into a polarized outlet
only one way, If the plug does not fit fully into the outlet,
reverse the plug, If it still does not fit, contact a qualified
electrician, Do not attempt to modify the plug in any way.
a) A short power-supply cord (or detached power-supply cord)
is to be provided to reduce risks resulting from becoming
entangled in or tripping over a long cord.
b) Longer detachable power-supply cords or extension cords
are available and may be used if care is exercised in their use.

c) If a long detachable power-supply cords or extension cord is
used,
1) The marked electrical rating of the detachable power-supply
cord or extension cord should be at least as great as the electrical
rating of the appliance.
2) If the appliance if of the grounded type, the extension cord
should be a grounding-type 3-wire cord,
3) The longer cord should be arranged so that it will not drape
over the counter top or table top where it can be pulled on by
children or tripped over.
KNOW YOUR COFFEE MAKER
ON/OFF button
Coffee/steam knob
Ready indicator
Power indicator
Funnel handle
Metal funnel
Steel mesh
Drip tray
Removable cup shelf
Tank cover
Handle
Detachable tank
Steam wand
Plastic sleeve
Press bar
Measuring spoon
Cup warming plate

To make a cup of good hot Espresso coffee, we recommend you
preheating the appliance before making coffee, including the
funnel, steel mesh and cup, so that the coffee flavour can not
be influenced by the cold parts.
After about one minute, turn the coffee/steam knob to the
“ ” position to stop brewing, you can pour the water in
container out then clean them thoroughly, now you can
start brewing.
Note: There may be noise when pumping the water on the
first time, it is normal, the appliance is releasing the air in
the appliance. After about 20s, the noise will disappear.
6.
Remove the detachable tank and open the tank cover to fill
it with desired water, the water level should not exceed the
“MAX” mark in the tank. Then place t he tank into the
appliance properly.
Set steel mesh into metal funnel, make sure the tube on the
funnel aligns with groove in the appliance, then insert the
funnel into the appliance from the “Insert” position, and
1.
2.
PRE-HEATING
BEFORE THE FIRST USE
To ensure the first cup of coffee tastes excellent, you should
rinse the coffee maker with warm water as follows:
Pour water into water tank, the water level should not
exceed the “MAX” mark in the tank. Then close the water
tank cover.
Note: the appliance is supplied with a detachable tank for
easy cleaning, you can fill the tank with water firstly, and
then put the tank into the appliance.
Set steel mesh into metal funnel (no coffee in steel mesh).
Place an espresso cup (your cup) on removable cup shelf.
Make sure the coffee/steam knob is on the “ ” position.
Note: the appliance is not equipped with jug, please use
your jug or coffee cup.
Connect to power source, press down the ON/OFF button
once. The red indicator illuminates.
The appliance begins to be pre-heated until the green
indicator illuminates, it shows the pre-heating is finished.
Turning the coffee/steam knob to the “ ” position, and
water will flow out.
1.
2.
3.
4.
5.

MAKE ESPRESSO COFFEE
Remove the metal funnel by turning it in clockwise, set
steel mesh into metal funnel. Add coffee powder to steel
mesh with measuring spoon, a spoon coffee powder can
make about a cup of top-grade coffee, then press the
ground coffee powder tightly with the tamper.
Then insert the funnel into the appliance from the “Insert”
position and release the press bar, and you can fix them
into coffee maker firmly through turn it anticlockwise until
it is at the lock position.(See Fig. 1).
Pour out the hot water in the cup. Then place the hot cup
(your cup) on removable cup shelf.
At the time, the green indicator illuminates, once the green
lamp illuminates, you should turn the coffee/steam knob to
the “ ” position, waiting for a moment, there will be coffee
flowing out.
NOTE: During brewing coffee or making steam, it is normal
that the green indicator is likely to extinguish, it only means
that the heater is heating up to keep the temperature at the
standard range.
You should turn the coffee/steam knob to the “ ” position
when desired coffee is obtained or the colour of coffee
1.
2.
3.
4.
5.
can fix them into coffee maker firmly through turn it
anticlockwise until it is at the lock position.(See Fig. 1).
Place an espresso cup (your cup) on removable cup shelf.
Then connect the appliance to power supply source. Make
sure the coffee/steam knob is on the “ ” position.
Press down ON/OFF button once, the red indicator turns
on, which means that the appliance enters into standby
condition.
Note: The appliance will be cut off automatically if without
any operation within 25 minutes in the standby condition.
When the green indicator illuminates, you should turn the
coffee/steam knob to the “ ” position, there will be hot
water flowing out. After about one minute, close the
coffee/steam knob by turning the coffee/steam knob again
to the “ ” position”. The pre-heating is finished.
3.
4.
5.
6.

MAKE CAPPUCCINO
changes weak obviously, the coffee maker stops working ,
your coffee is ready now.
WARNING: Do not leave the coffee maker unattended
during making the coffee, as you need operate manually
sometimes!
Hold and press the ON/OFF button for about 3 seconds, the
appliance will be shut off and all the indicators will
extinguish.
After finishing making the coffee, you can take the metal
funnel out by turning it clockwise, then pour the coffee
residue out with the steel mesh pressed by press bar.
Let them cool down completely, then rinse under running
water.
6.
7.
8.
You get a cup of cappuccino when you top up a cup of espresso
with frothing milk.
NOTE: during making steam, the metal funnel must be
assembled in position.
Method:
Prepare espresso first with container big enough according
to the part “MAKE ESPRESSO COFFEE”.
Turn the coffee/steam knob to the “ ” position, waiting
for until the green indicator illuminates.
Fill a jug with about 100 grams of milk for each cappuccino
to be prepared, you are recommended to use whole milk at
refrigerator temperature (not hot!).
NOTE: In choosing the size of jug, it is recommended the
diameter is not less than 70±5mm, and bear in mind that
the milk increases in volume by 2 times, make sure the
height of jug is enough.
Insert the steam wand with plastic sleeve into the milk
about two centimetre, then turn the coffee/steam knob to
the “ ” position, steam will come out from the steam
outlet. Froth milk in the way moving vessel round from up
to down.
Warning: Be sure to operate carefully as the steam may
result in scald to person.
When the required purpose is reached, you can turn the
coffee/steam knob to the “ ” position
(see Fig.2).
1.
2.
3.
4.
5.

PRODUCING STEAM TO HEAT LIQUIDS OR
FROTH MILK SINGLY
NOTE: Clean steam outlet with wet sponge immediately
after steam stops generating, but care not to hurt!
Pour the frothed milk into the espresso prepared, now the
cappuccino is ready. Sweeten to taste and if desired,
sprinkle the froth with a little cocoa powder.
Hold and press the ON/OFF button for about 3 seconds, the
appliance will be shut off and all the indicators will
extinguish.
6.
7.
Remove the detachable tank and fill it with desired water,
the water level should not exceed the “MAX” mark in the
tank. Then place the tank into the appliance properly.
Then connect the appliance to power supply source.
Press down ON/OFF button once, the red indicator
illuminates.
1.
2.
3.
The steam wand can be used to froth milk singly or make hot
beverages like drinking chocolate, water or tea.
Method:
After about one minute, turn the coffee/steam knob to the
“ ” position to stop brewing, you can pour the water in
container out then clean them thoroughly, now you can
start brewing.
Note: There may be noise when pumping the water on the
first time, it is normal, the appliance is releasing the air in
the appliance. After about 20s, the noise will disappear.
Remove the detachable tank and open the tank cover to fill
it with desired water, the water level should not exceed the
“MAX” mark in the tank. Then place t he tank into the
appliance properly.
Set steel mesh into metal funnel, make sure the tube on the
funnel aligns with groove in the appliance, then insert the
funnel into the appliance from the “Insert” position, and
Pour water into water tank, the water level should not
exceed the “MAX” mark in the tank. Then close the water
tank cover.
Note: the appliance is supplied with a detachable tank for
easy cleaning, you can fill the tank with water firstly, and
then put the tank into the appliance.
Set steel mesh into metal funnel (no coffee in steel mesh).
Place an espresso cup (your cup) on removable cup shelf.
Make sure the coffee/steam knob is on the “ ” position.
Note: the appliance is not equipped with jug, please use
your jug or coffee cup.
Connect to power source, press down the ON/OFF button
once. The red indicator illuminates.
The appliance begins to be pre-heated until the green
indicator illuminates, it shows the pre-heating is finished.
Turning the coffee/steam knob to the “ ” position, and
water will flow out.
Turning the coffee/steam knob to the “ ” position and
waiting for a moment, the appliance begins to be heated
until the green indicator illuminates, it shows the heating is
finish.
Dip the steam wand with plastic sleeve into the liquid to be
heated or the intended froth milk. Turn the coffee/steam
knob to the “ ” position and start making steam.
When the required temperature is reached or the frothing
milk is obtained, you can turn the coffee/steam knob to the
“ ” position.
Hold and press the ON/OFF button for about 3 seconds, the
appliance will be shut off and all the indicators will
extinguish.
4.
5.
6.
7.
AUTOMATICALLY SHUT-OFF FUNCTION
The appliance has the function of shut-off power automatically,
when the power cord is plugging into the power outlet and the
ON/OFF button has been pressed, if without any operation
within 25 minutes, or if the pump has worked continuously for
3 minutes under “ ” mode, or if the appliance has worked for
25 minutes under“ ”mode, the appliance will cut off power

Cut off power source and let the coffee maker cool down
completely before cleaning.
Clean housing of coffee maker with moisture-proof sponge
often and clean water tank, drip tray and removable shelf
regularly then dry them.
Note: Do not clean with alcohol or solvent cleanser. Never
immerse the housing in water for cleaning.
Detach the metal funnel by turning it clockwise, get rid of
coffee residue inside, then you can clean it with cleanser,
but at last you must rinse with clear water.
Clean all the attachments in the water and dry thoroughly.
1.
2.
3.
4.
CLEAN AND MAINTENANCE
automatically and the power indicator will be extinguished, if
you want to continue operating, you shall press the ON/OFF
button once, the power indicator will illuminated, the
appliance can be operated.
CLEANING MINERAL DEPOSITS
To make sure your coffee maker operating efficiently,
internal piping is cleanly and the peak flavor of coffee, you
should clean away the mineral deposits left every 2-3
months.
Fill the tank with water and descaler to the MAX level ( the
scale of water and descaler is 4:1, the detail refers to the
instruction of descaler. Please use “household descaler”,
you can use the citric acid (obtainable from chemist’s or
drug stores) instead of the descaler (the one hundred parts
of water and three parts of citric acid).
According to the program of pre-heating, put the metal
funnel (no coffee powder in it) and carafe (jug) in place.
Brewing water per “ PRE-HEATING”.
Press down ON/OFF button once, the red indicator
illuminates, make sure the coffee/steam knob is on the “ ”
position, and waiting for a moment, the coffee maker
begins to be heated.
When the green indicator illuminates, it shows the heating
is finish. Turning the coffee/steam to the “ ” position and
make two cups coffee (about 2Oz). Then turn the
coffee/steam knob to the “ ” position and wait for 5s.
1.
2.
3.
4.
5.

Remove the detachable tank and fill it with desired water,
the water level should not exceed the “MAX” mark in the
tank. Then place the tank into the appliance properly.
Then connect the appliance to power supply source.
Press down ON/OFF button once, the red indicator
illuminates.
TROUBLE SHOOTING
SYMPTOM CAUSE CORRECTIONS
Water leaks from the
bottom of coffee
maker.
There is much water
in the drip tray. Please clean the drip tray.
Please contact with the
authorized service
facility for repairing.
Get rid of them.
Clean coffee maker per the
content in “before the first
use” for several times.
Please use fresh coffee
powder, or store unused
coffee powder in a cool,
dry place. After opening
a package of coffee
powder, reseal it tightly
and store it in a refrigerator
to maintain its freshness.
Plug the power cord into
a wall outlet correctly, if
the appliance still does
not work, please contact
with the authorized service
facility for repairing.
The coffee maker is
malfunction.
There is some coffee
powder on filter edge.
No clean correctly
after cleaning
mineral deposits.
The coffee powder is
stored in a hot, wet
place for a long time.
The coffee powder
turns bad
The power outlet is
not plugged well.
Water leaks out of
outer side of filter.
Acid (vinegar) taste
exists in Espresso
coffee.
The coffee maker
cannot work any
more.
Once the green indicator illuminates. Make steam for 2min,
then turn the coffee/steam knob to the “ ” position to stop
making steam.Hold and press the ON/OFF button for about
3 seconds, the appliance will be shut off and all the
indicators will extinguish, make the descalers deposit in
the unit at least 15 minutes.
Restart the unit and repeat the steps of 4-6 at least 3 times.
Then turning the coffee/steam knob to the “ ” position,
when the green lamp illuminates, turn the coffee/steam
knob to the “ ” position to brew until no descaler is left.
Then brewing coffee (no coffee powder) with tap water in
the MAX level, repeat the steps of 4-6 for 3 times (it is not
necessary to wait for 15 minutes in step of 6), then brewing
until no water is left in the tank.
Repeat the step of 9 at least 3 times to make sure the piping
is cleanly.
6.
7.
8.
9.
10.

Only after the green
indicator is illuminated,
the steam can be used
to froth.
Use high and narrow cup.
Use whole milk or
half-skimmed milk
The green indicator
is not illuminated.
The container is too
big or the shape is
not fit.
You have used
skimmed milk
Do not take apart the appliance by yourself if the cause of failure is not found,
you had better contact certified serving center.
The steam cannot
froth.
To make sure your coffee maker operating efficiently,
internal piping is cleanly and the peak flavor of coffee, you
should clean away the mineral deposits left every 2-3
months.
Fill the tank with water and descaler to the MAX level ( the
scale of water and descaler is 4:1, the detail refers to the
instruction of descaler. Please use “household descaler”,
you can use the citric acid (obtainable from chemist’s or
drug stores) instead of the descaler (the one hundred parts
of water and three parts of citric acid).
According to the program of pre-heating, put the metal
funnel (no coffee powder in it) and carafe (jug) in place.
Brewing water per “ PRE-HEATING”.
Press down ON/OFF button once, the red indicator
illuminates, make sure the coffee/steam knob is on the “ ”
position, and waiting for a moment, the coffee maker
begins to be heated.
When the green indicator illuminates, it shows the heating
is finish. Turning the coffee/steam to the “ ” position and
make two cups coffee (about 2Oz). Then turn the
coffee/steam knob to the “ ” position and wait for 5s.