GEZE Slimdrive SLT Quick guide

Slimdrive SLT
Product family
EN Installation and service instructions
192483-01

Slimdrive SLT product family
2
Contents
1 Introduction...............................................................................................................................................................3
1.1 Symbols and illustrations ..............................................................................................................................................................................3
1.2 Revisions and validity......................................................................................................................................................................................3
1.3 Product liability .................................................................................................................................................................................................3
1.4 Reference documents.....................................................................................................................................................................................3
2 Fundamental safety notes....................................................................................................................................4
2.1 Intended use.......................................................................................................................................................................................................4
2.2 Safety notes ........................................................................................................................................................................................................4
2.3 Safety-conscious working.............................................................................................................................................................................5
2.4 Environmentally conscious working .........................................................................................................................................................5
2.5 Safety notes related to transportation and storage............................................................................................................................5
2.6 Qualication .......................................................................................................................................................................................................5
3 About this document.............................................................................................................................................6
3.1 Overview..............................................................................................................................................................................................................6
4 Overview.....................................................................................................................................................................7
4.1 Diagrams..............................................................................................................................................................................................................7
4.2 Tools and aids.....................................................................................................................................................................................................7
4.3 Torques.................................................................................................................................................................................................................8
4.4 Components and assembly groups...........................................................................................................................................................8
5 Installation..................................................................................................................................................................8
5.1 Preparations to be made on-site ................................................................................................................................................................8
5.2 Mounting the track ..........................................................................................................................................................................................8
5.3 Mounting the oor guide............................................................................................................................................................................11
5.4 Installing the moving leaf............................................................................................................................................................................12
5.5 Fitting the tooth belt.....................................................................................................................................................................................19
5.6 Setting the stop buer ................................................................................................................................................................................ 22
5.7 Installing cable guides................................................................................................................................................................................. 22
5.8 Fitting the transformer ground................................................................................................................................................................ 23
6 Production test and commissioning.............................................................................................................. 24
6.1 Connecting the drive ................................................................................................................................................................................... 24
6.2 Mounting the cover...................................................................................................................................................................................... 25
6.3 Mounting the cover suspension piece .................................................................................................................................................. 25
6.4 Mounting the safety devices..................................................................................................................................................................... 29
6.5 Installing operating elements/switches/push buttons................................................................................................................... 29
6.6 Commissioning the door system............................................................................................................................................................. 29
6.7 Dismantling ..................................................................................................................................................................................................... 29
7 Service and maintenance .................................................................................................................................. 29
7.1 Mechanical service........................................................................................................................................................................................ 29
7.2 Maintenance.................................................................................................................................................................................................... 30
8 Troubleshooting.....................................................................................................................................................31
8.1 Mechanical faults............................................................................................................................................................................................31
8.2 Replacing roller carriage..............................................................................................................................................................................31
8.3 Electrical faults................................................................................................................................................................................................ 32
9 Drive type plate..................................................................................................................................................... 33
10 Inspection of the installed door system....................................................................................................... 34
10.1 Measures to prevent and secure hazardous areas............................................................................................................................ 34
10.2 Installation checklist Slimdrive SLT......................................................................................................................................................... 34

Slimdrive SLT product family
3
Introduction
1 Introduction
1.1 Symbols and illustrations
Warning notices
In these instructions, warning notices are used to warn against material damage and injuries.
XAlways read and observe these warning notices.
XObserve all measures marked with the warning symbol and warning word.
Warning
symbol
Warning word Meaning
DANGER Danger to persons.
Non-compliance will result in death or serious injuries.
WARNING Danger to persons.
Non-compliance can result in death or serious injuries.
CAUTION Danger to persons.
Non-compliance can result in minor injuries.
Further symbols and illustrations
Important information and technical notes are highlighted to explain correct operation.
Symbol Meaning
means “important note”.
Information to prevent property damage, to understand or optimise the operation sequences.
means “additional Information”
XSymbol for an action: This means you have to do something.
XIf there are several actions to be taken, keep to the given order.
1.2 Revisions and validity
Version 01: valid for Slimdrive SLT product family from date of manufacture 2021
1.3 Product liability
In compliance with the liability of the manufacturer for his products as dened in the German “Product Liability
Act”, compliance with the information contained in this brochure (product information and intended use, misuse,
product performance, product maintenance, obligations to provide information and instructions) must be ensured.
Failure to comply releases the manufacturer from his statutory liability.
1.4 Reference documents
Type Name
Wiring diagram Automatic sliding doors DCU1-NT/DCU1-2M-NT
Additional wiring diagrams Automatic sliding doors DCU1-2M-NT, door controller DCU1-2M-NT for
automatic sliding doors in escape routes, FR variants DUO, LL, RWS
User manual Automatic sliding door systems
Faults and corrective measures DCU1-NT/DCU1-2M-NT Drive electronics for automatic sliding doors
Cable plan Automatic sliding door systems
Safety analysis Automatic sliding doors
Pre-installation instructions Slimdrive SLT product family
Installation instructions Slimdrive SLT girder section and side panel
Additional installation instructions Rod locking
These documents are subject to change. Use only the most recent version.

Slimdrive SLT product family
4
Fundamental safety notes
2 Fundamental safety notes
GEZE GmbH is referred to as GEZE below.
2.1 Intended use
The sliding door system is used for the automatic opening and closing of a building passage.
The sliding door system may only be used in a vertical installation position and in dry rooms within the permitted
application area.
The sliding door system is designed for pedestrian trac in buildings.
The sliding door system is not designed for the following uses:
àfor industrial use
àfor area of application which do not serve pedestrian trac (such as garage doors)
àon mobile objects such as ships
The sliding door system may only be used:
àin the modes of operation provided for by GEZE
àwith the components approved / released by GEZE
àwith the software delivered by GEZE
àin the installation variants / types of installation documented by GEZE
àwithin the tested/approved area of application (climate / temperature / IP rating)
Any other use is considered non-intended and will lead to the exclusion of all liability and warranty claims to GEZE.
2.2 Safety notes
àIntervention and modications which inuence the safety technology and functionality of the sliding door
system may only be carried out by GEZE.
àProblem-free and safe operation assumes proper transportation, proper set-up and installation, qualied
operation and correct maintenance have taken place.
àThe relevant accident prevention regulations and other generally recognised safety technology or health
& safety rules must be kept.
àOnly original accessories, original spare parts and accessories approved by GEZE guarantee problem-free
function of the sliding door system
àThe mandatory installation, maintenance and repair work must be performed by properly trained personnel
authorised by GEZE.
àThe country-specic laws and regulations are to be observed during safety technology tests.
àIf unauthorised changes are made to the system, GEZE cannot be held liable in any way whatsoever for any
resulting damage, and the statement of approval for use in escape and rescue routes is no longer valid.
àGEZE does not accept any warranty for combinations with third-party products.
àOnly original GEZE parts may be used for repair and maintenance work.
àThe connection to the mains voltage must be completed by an electrician or specialised electrical technician.
Perform the power connection and protective earth connection test in accordance with VDE 0100 Part 600.
àUse an on-site 10-A overload cut-out as the line-side disconnecting device.
àProtect the display programme switch against unauthorised access.
àIn compliance with Machinery Directive 2006/42/EC, a risk analysis must be performed and the door system
identied in accordance with CE Marking Directive 93/68/EEC before the door system is commissioned.
àObserve the latest versions of guidelines, standards and country-specic regulations, in particular:
àDIN 18650: “Building hardware – Powered automatic doors”
àVDE 0100, Part 600: “Installation of low-voltage systems”
àEN 16005: “Power operated pedestrian doorsets – Safety in use– Requirements and test methods”
àEN 60335-1: “Household and similar electrical appliances - Safety Part 1: General requirements”
àEN 60335-2-103: “Household and similar electrical appliances - Safety: Special requirements for drives for
gates, doors and windows”
àA relevant regulation must be used to select appropriate fastening materials, such as the guidelines for
planning and carrying out installation of windows and front doors for new constructions and renovations
of the RAL-Gütergemeinschaft Fenster und Haustüren e.V.
àDo not loosen screw-tted , electrical ground connections.

Slimdrive SLT product family
5
Fundamental safety notes
The product should be installed or incorporated in such a way that eortless access to the product is guaranteed
during any repairs and/or maintenance, and that any removal costs do not stand out of economic proportion to
the value of the product.
2.3 Safety-conscious working
àSecure workplace against unauthorised entry.
àWatch the swivelling range of long system parts.
àNever carry out work with a high safety risk (e.g. installing the drive, cover or door leaf) while alone.
àSecure the cover/drive panels against falling.
àSecure non-xed components to prevent them falling.
àUse only the cables specied on the cable plan provided. Cables must be shielded in compliance with the
wiring diagram.
àSecure loose, internal drive cables with cable ties.
àBefore working on the electrical system:
àDisconnect the drive from the 230 V mains and secure it against being switched back on again. Check isolation
from power supply.
àDisconnect the control unit from the 24 V rechargeable battery.
àNote that if an Uninterruptible Power Supply (UPS) is used, the system will still be supplied with voltage despite
the fact that the power supply is disconnected.
àAlways use insulated wire-end ferrules for wire cores.
àMake sure of sucient lighting.
àUse safety glass.
àAttach safety stickers to glass door leaves.
àDanger of injury with opened drive. Hair, clothing, cables, etc. can be drawn in by rotating parts.
àRisk of injury by trapping, knocking, shearing and hair etc. being pulled in at unsecured points.
àRisk of injury due to glass breakage. Always only use safety glass.
àRisk of injury due to sharp edges on the drive and door leaf.
àRisk of injury during installation through freely moving parts.
2.4 Environmentally conscious working
àWhen disposing of the door system, separate the dierent materials and have them recycled.
àDo not dispose of batteries and rechargeable batteries with household waste.
àComply with the statutory regulations when disposing of the door system and the batteries/rechargeable
batteries.
2.5 Safety notes related to transportation and storage
àThe door system and its parts are not built for hard impacts or for falling from a height.
XDo not throw, do not drop.
àStorage temperatures under –30 °C and above +60 °C can result in damage to the device.
àProtect against humidity.
àUse special glass transport devices (e.g. A-frames) for transporting glass.
àSeparate several panes on a frame or during storage using intermediate layers (e.g. cork pads, paper or plastic cords).
àAlways store glass in a vertical position on level and load-bearing ground. Use suitable material as a support
(e.g. wooden slats).
àIn the case of insulated glass, make sure that it is placed ush across the entire element thickness on at least
2 supports.
àDuring storage and support, safety devices must not cause any damage to the glass or edge seal of insulated
glass and must be attached at on the pane surface.
àDry, well ventilated, closed, weather-proof and UV-protected rooms are suitable as storage areas
2.6 Qualication
Observe country-specic regulations!
Applicable in Germany:
Companies that carry out the pre-assembly of sliding door drives for escape routes must be licensed as an
expanded manufacturing facility by the testing institution that issued the type approval certicate.

Slimdrive SLT product family
6
About this document
3 About this document
3.1 Overview
These instructions describe the installation of automatic sliding door systems of the Slimdrive SLT product family
without side panel. The installation of the side panels and the girder section installation is described in the instal-
lation instructions “Girder section with side panel”.
The following drawings illustrate installation with ISO prole systems.
The IGG prole is also possible in combination with the Slimdrive SLT.
View from the front

 
View from above (Slimdrive SLT with ISO proles)
3
2
4
View from the side (Slimdrive SLT with ISO proles)
1 Drive of the sliding door system
2 Moving leaf
3 Floor guide
4 Safety leaf
1
2
3

Slimdrive SLT product family
7
Overview
4 Overview
4.1 Diagrams
Number Type Name
70487-0-007 Drive drawing Slimdrive SLT, drive
70487-0-010 Dimensioned drawing Slimdrive SLT/SLT-FR 2M, 4-leaf with rod locking
70487-ep01 Installation diagram Slimdrive SLT / -FR 2 M, insulated glass doors, post-rail construction
70487-ep06 Installation diagram Slimdrive SLT with oor lock
70487-ep07 Installation diagram Slimdrive SLT/SLT-FR 2M with IGG
70487-ep10 Installation diagram Slimdrive SLT/SLT-FR 2M ISO, Lock M, post-rail
70487-ep20 Installation diagram IGG prole system
70487-ep21 Installation diagram 2-leaf, left-hand side, 1-leaf, left hand slide to open
70487-ep22 Installation diagram 2-leaf, right-hand side, 1-leaf, right hand slide to open
70487-ep27 Installation diagram Wooden leaf
70487-ep40 Installation diagram ISO with rod locking
70715-9-9818 Installation diagram Continuous oor guide SL + SLT
70484-ep04 Installation diagram Safety leaf for sliding door drives
70484-ep15 Installation diagram Protective leaf mounting
70717-ep02 Installation diagram Slimdrive SLT, ISO self-supporting girder section
70717-ep04 Installation diagram Slimdrive SLT, girder section lintel installation
70717-ep08 Installation diagram Slimdrive SLT, self-supporting girder section Lock M
70717-ep09 Installation diagram Slimdrive SLT, girder section lintel installation Lock M
70484-2-0572 Component drawing Cover, bespoke SL/SLT
70484-2- 0574 Component drawing Track, bespoke
70484-2-0467 Component drawing Track 6500 and 4500 mm - 2-leaf - with rod locking
70484-2-0575 Component drawing Track, bespoke - 2-leaf - with rod locking
70484-2-0691 Component drawing Track, bespoke - 1-leaf - with rod locking
70715-1-0159 Assembly group drawing Floor guide continuous
70715-9-9837 Installation drawing SLT insulated glass leaf
70717-9-0967 Installation drawing SL/ SLT side panel
The diagrams are subject to change without notice. Use only the most recent version.
4.2 Tools and aids
Tool Closer size
Tape measure
Marking pen
Torque spanner
Allen key 2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm, 6 mm
Open-ended spanner 8 mm, 10 mm, 13 mm, 15 mm, 13 mm at (GEZE specialised tool)
Ring spanner 8 mm
Screwdriver set Floor guide slit up to 6 mm, cross-slot PH2 and PZ2
Torx key TX 20 (bit insert length at least 110 mm)
Side-cutting pliers
Crimping pliers for cables
Wire stripper
Multimeter
Display programme switch/Service terminal ST 220/GEZEconnects

Slimdrive SLT product family
8
Installation
4.3 Torques
The torques are given at the respective installation step.
4.4 Components and assembly groups
See the ep-drawing for the required installation situation and drive drawings.
5 Installation
WARNING!
Risk of fatal injury due to electric shock!
XDo not loosen screw-tted electrical protective earth connections.
XSecure workplace against unauthorised entry.
XAlways work with a second person.
XUse a stepladder or stepstool with test seal.
XKeep inside area of track clean.
5.1 Preparations to be made on-site
XCheck the preparations made on site by the customer to ensure proper installation:
àType and load capacity of the façade construction or suspending frame
àEvenness of the installation surface
àEvenness of the nished oor level
àCable plan requirements
5.2 Mounting the track
View from the side








Slimdrive SLT product family
9
Installation
View from above


1 Fastening drill holes
2 Mounting prole
3 Track
4 Sealing proles
5 Wall strips
XDetermine the installation height of the mounting prole (2).
Take unevenness of wall and oor into account.
XAlign the mounting prole (2) horizontally.
XMark the fastening drill holes (1).
XPrepare the cable guide according to on-site conditions, e.g. hold the cap on the left side of the mounting
prole (2) and transfer the cable feed through.
XRemove the mounting prole.
XDrill fastening holes (1) into the mounting prole.
XCut out mounting prole (2) in the marked position.
XAlign the mounting prole (2) in the installation area and use it as a drilling template.
XDrill the drill holes.
XScrew on the mounting prole (2).
XSuspend the track (3) with pre-assembled assemblies and caps in the mounting prole.
XAlign the track laterally.
XInstall the sealing proles (4).
XPress rubber seal into the draught sealing proles.
With 1-leaf door systems:
XInstall the wall strips (5).

Slimdrive SLT product family
10
Installation
Clamping the track with clamping strips
WARNING!
Risk of injury!
Unsecured components may fall when under load.
XRemove the cap with side plate.
The track (3) is clamped to the mounting prole (1) using clamping strips (2) so that the track (3) is attached so as
to be prevented from twisting.
XSlide 7 clamping strips (2) between the
mounting prole (1) and the track (3).
Post/rail version:
XPosition inner 5 clamping strips (2) at the
level of the inner posts and position others
between them.
Wall and ceiling installation:
XMount the cap with side plate (see pre-in-
stallation instructions).
XPosition one clamping strip (2) on the
exterior of each mounting prole/track
as follows:
àLeft at the transition between the cap
and track,
àRight at an appropriate distance from the
end of the track.



Mounting the cover
XDisconnect the cover (2) at the disconnection
point (3) from the residual piece (4).
XDispose of the residual piece.
XIf necessary. slide the cover (2) in to the
mounting prole (1).






Slimdrive SLT product family
11
Installation
5.3 Mounting the oor guide
àThe oor guide is selected based on the on-site conditions. One of the following oor guide options must be used.
àFor further information see the respective installation drawing, Chapter 4.1.
5.3.1 Angled oor guide, oor mounting (option)
Angled oor guide with moving leaf left hand slide to open
XScrew in the angled oor guide (6) with 2 suitable countersunk
head screws (1) and (2).
Angled oor guide with moving leaf right hand slide to open
XScrew in the angled oor guide (6) with 2 suitable countersunk
head screws (3) and (2).
1 Countersunk screw for moving leaf left hand slide to open
2 Countersunk screw
3 Countersunk screw for moving leaf right hand slide to open
4 outside
5 inside
6 Angled oor guide






5.3.2 Adjustable angled oor guide wall installation (option)
XScrew the fastening bracket (2) onto the xed
panel (1) using two screws (6) (tightening
torque 10 Nm).
XAlign the moving leaf (4) and thereby the
adjusting angle (3).
XTighten the screw (5).
XIf there is no xed panel, mount the oor
guide onto the wall using suitable attachment
materials.
1 2 3
4
5
6
5.3.3 Continuous oor guide (option)
àFor assembly of the continuous oor guide, see the “Continuous oor guide” assembly drawing.
àFor further information see the respective installation diagrams, Chapter 4.1.

Slimdrive SLT product family
12
Installation
5.4 Installing the moving leaf
5.4.1 Install the door suspension plates on the moving leaf
The door suspension plates are installed during glazing of the moving leaves. In case of subsequent installation
of the door suspension plates, the frames of the moving leaves must be dismantled (see installation instructions
for moving leaves).
See the installation drawing for the moving leaf for the position of the bracket support (distance x, y and overhang).
Installing the door suspension plates
View from the side
Moving leaf
inner





 


Moving leaf
outer





 


View from above:
1 2
3
4
33
1 Door suspension plate
2 Screws
3 Secondary closing edge
4 Main closing edge
XScrew the door suspension plates (1) to the moving leaf using screws (2).
XDo not tighten the screws yet.

Slimdrive SLT product family
13
Installation
5.4.2 Installing the connecting arm and driver
àDrivers must not touch any obstacle over the entire travel path.
àSee the drive drawing for the precise position of the driver.
4-leaf
Installing the connecting arm and long driver:
XUse 2 hexagon screws (5) to screw the
long driver (6) to the inner left moving leaf
(torque 15Nm).
XClamp the connecting arm (3) in place using
2 setscrews (4) (torque 3Nm).




Installing the connecting arm and short driver:
XUse 2 hexagon screws (7) and intermediate
plate (9) to screw the short driver (8) to the
inner right moving leaf (torque 15Nm).
XClamp the connecting arm (3) in place using
2 setscrews (4) (torque 3Nm).






Slimdrive SLT product family
14
Installation
2-leaf
Installing the connecting arm and short driver:
For drive SLT-FR 2-leaf, right, an angled driver, short (8) is mounted.
XUse 2 hexagon screws (7) and intermediate
plate (9) to screw the short driver (8) to the
inner moving leaf (torque 15Nm).
XClamp the connecting arm (3) in place using
2 setscrews (4) (torque 3Nm).





5.4.3 Fitting the moving leaves
WARNING!
Risk of injury caused by moving leaf falling over!
The moving leaves are very heavy.
XAt least 2 people should work together to set up the moving leaf.
WARNING!
Risk of injury due to glass breakage.
XAt least 2 people should work together to set up the moving leaf.
XRemove the roller carriage from the transport
locking device, push the stop buer outwards.
XHang door suspension plates (2) from the front
into the suspension bolts of two roller carriages.
XSecure the moving leaf using lock nuts (1).
Do not tighten the lock nuts (1) yet.



Slimdrive SLT product family
15
Installation
5.4.4 Installing the wire rope
Overview (4-leaf shown)
    

 

   
1 Rope pulley, short
2 Suspension piece
3 Clamping piece
4 Tensioning piece
5 Wire rope
6 Rope pulley, long
7 Connecting arm
XPush outer moving leaf into open position.
approx.
20 mm
6252
XPosition suspension piece (2) on the track approx 20mm from the centre axis of the long rope pulley (6)
and clamp in position.
XThread in the wire rope (5) from right to left into the suspension piece (2) and pull through until the nipple
contacts.
61
XRoute the wire rope around the long rope pulley (6) of the moving leaf.
XRoute the wire rope around the short rope pulley (1) of the moving leaf.

Slimdrive SLT product family
16
Installation
33 2
30 mm
XThread the wire rope into the clamping piece (3) and pull through.
XPosition the clamping piece (3) on the track (approx. 30mm distance from the suspension part (2)) and
clamp in position.
XTighten the wire rope by hand and secure in the clamping piece (3) (screws from underneath).
4
2 mm
3
XPosition the tensioning piece (4) approx. 2mm away from the clamping piece (3) and clamp tightly.
XUndo the xing screws of the clamping piece (3) while at the same time, with the help of a screwdriver,
push the clamping piece (3) to the left and tighten the wire rope slightly.
XTighten the clamping piece (3) on the track.
XCut o protruding end of the wire rope. Length of the remaining overhang approx. 20mm.
XHook inner moving leaf in place and use lock nuts to pre-secure moving leaf.
XThread the wire rope into the connecting arm
(7), but do not clamp yet.
To reach the connecting arm, the moving
leaves must be placed in the closed position.
The connecting arm is then accessible from
the outside.


Slimdrive SLT product family
17
Installation
5.4.5 Adjusting the moving leaves
WARNING
Risk of crushing!
The moving leaves are still unsecured and move easily.
XEnsure that the moving leaves are not moved accidentally or by unauthorised persons!
XObserve the applicable standards and guidelines on crushing, shearing and drawing-in spots.
XLoosen the locknut (1).
Adjusting the inclination and level of the moving leaves





XAdjust the inclination and level of the moving leaves using the hex of the suspension bolts (2):
Horizontal adjustment of the moving leaves






XMove the moving leaves horizontally in the leaf suspension (3).
XMake the individual moving leaf move smoothly.
XAlign moving leaves ush with each other. Ensure the same level and parallel closing edges when doing so.
XAlign moving leaves to maximum opening width.
Once all the moving leaves have been adjusted:
XTighten the lock nut (1) (torque 20Nm).

Slimdrive SLT product family
18
Installation
Securing the moving leaves
XFix the stop buers (5) behind the outer roller
carriage (4).

XPush the vertically adjustable strip with brush into the moving leaf until it snaps into place (see the assembly
drawing for the Slimdrive SL moving leaf).
XMount the guide rails in the oor area (see the assembly drawing for the Slimdrive SLT moving leaf).
XSlide the moving leaves to the closing position.

7
XClamp the wire rope on the connecting arm (6).
XInstall the covers (7) for rope pulleys.

Slimdrive SLT product family
19
Installation
5.5 Fitting the tooth belt
1-leaf
XScrew the toothed belt locking (2) on the short
driver (1) (torque 10Nm).


2-leaf
XScrew the toothed belt locking (2) on the short
driver (1) (torque 10Nm).


XFix the toothed belt locking (1) on the
long driver (4) using the screw (3) and
the counterplate (2) (torque 10 Nm).





Slimdrive SLT product family
20
Installation
5.5.1 Tensioning the tooth belt
XThe tooth belt must be pre-tensioned with 300N ±35N (see drive drawing).
XUndo 2 screws (2).
XSlide the motor gear unit (3) to the right
by hand.
XUndo the screw (1) and move the sliding block
in such a way that a slot-head screwdriver can
be pushed between the sliding block and the
motor gear unit.
XTighten the screw (1) (torque 10Nm).
XPush the slot-head screwdriver into the gap
and lever it until the tooth belt is tensioned.
XTighten 2 screws (2) (torque 15Nm).


5.5.2 Setting the closing position
XLoosen screws (1).
XPush the moving leaf to the closed position
and align in the centre.
XTighten the screws (1) when the exact closing
position has been set (torque 10 Nm).

