GFW CATANIA 3 DOOR 4 DRAWER WARDROBE User manual

CATANIA 3 DOOR 4 DRAWER WARDROBE
ASSEMBLY INSTRUCTIONS
Thank you for purchasing the CATANIA 3 DOOR 4 DRAWER WARDROBE. Please read the
instructions carefully to ensure safe operation of the product.
Size: 1195 x 515 x 1950mm
PLEASE READ this sheet prior to assembly to familiarise yourself with the various stages of construction.
Carefully open the pack supplied and check the contents against the parts and ttings check list. Do not
destroy any of the packaging until you are certain that you have all the necessary parts for the assembly.
CAUTION: There are small components used in the construction of this unit. These loose items should be
kept away from young children whilst assembling your unit to avoid the danger of choking hazards.
Tools Required
V1 2022.07
Page 1of 26
3.5m/12'x 2
Person Required Approximate
Assembly Time
2.5 Hour

V1 2022.07
Page 2of 26
IMPORTANT - READ CAREFULLY - RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
INFORMATION
�Due to the size of this product we recommend that it is assembled in the room intended for use.
�When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for
assembly.
�Unwrap all packaging materials and place the components on top of the carton box or on a clean floor to
prevent it from scratching.
�Check the pack and make sure you have all the parts listed.
�Ensure that this product is fully assembled as illustrated before use.
�Check all screws or bolts are tightened and inspect regularly
�This product should only be used on firm, level ground.
�Keep small parts out of reach of children.
�Make sure the legs remain in contact with the ground.
�Tools not included.
WARNINGS
�DO NOT use power tools to construct this product.
�DO NOT over tighten screws or bolts.
�DO NOT use this product if parts are missing, damaged or worn.
�DO NOT sit or stand on the product.
�It is essential that this unit is xed to the wall with the brackets provided for safety reasons. NB wall xings are
not included. Please source suitable fixings for your wall type. If in doubt please consult a qualified
tradesperson.
�WARNING : Always ensure the area to be drilled is free from hidden electrical wires, water or gas pipes.
CARE INFORMATION
�Never use scourers, abrasives or chemical cleaners.
�To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or detergents as they
can bleach or damage the product.

V1 2022.07
Page 3of 26
Please check the pack contents before assembling the product. If any components are missing,
please contact your retailer. The ttings pack contains small items that should be kept away from
small children.
CODE QTY DIMENSIONPART NAME
A
B
C
1
D
E
Top Panel
Bottom Front Bar
Side Panel - L
Side Panel - R
Parts
CODE
F
15 x 495 x 1930mm
15 x 495 x 1930mm
15 x 495 x 1195mm
15 x 80 x 1164mm
15 x 80 x 1164mm
QTY DIMENSION
15 x 495 x 1410mm
PART NAME
Back Bar - Small 15 x 80 x 389mm
1
1
1
1
1
1
1
1
Top Bar Support 15 x 65 x 760mm
1
Q
Door - L 15 x 384 x 1459mm
15 x 65 x 1164mm
2
O
P
1
Door - R 15 x 384 x 1459mm
G1
N
Bottom Back Bar
Bottom Bar
15 x 384 x 1459mm
6 x 60 x 1405mm
2
R
S
15 x 140 x 519mm
X4
Drawer Back
3 x 344 x 528mm
4
Drawer Bottom
3 x 396 x 1876mm
3
Back Panel
Drawer Front - L
Drawer Front - R
15 x 190 x 595mm
Door - Centre
Door Support
Vertical Panel
15 x 40 x 1410mm
H1
Side Bar
G
H1
15 x 424 x 495mm
I1
Center Panel
15 x 480 x 1164mm
J1
Fix Panel
15 x 65 x 1164mm
K1
Front Bar - Long 1
15 x 50 x 574mm
L2
Front Bar - Short
15 x 80 x 760mm
M1
Back Bar
15 x 190 x 595mm
2
Drawer Side - L
BACK
PANEL
BACK
PANEL BACK
PANEL
DRAWER
BOTTOM
DRAWER
BOTTOM
15 x 140 x 350mm
V4
Drawer Side - R 15 x 140 x 350mm
W
T
U
4

0 cm
1 cm
2 cm
3 cm
4 cm
5 cm
Fixings (to scale)
0 cm
1 cm
2 cm
3 cm
V1 2022.07
Page 4of 26
35x
M3.5 x 15mm
G
CSK Screw
27x
EU 24
D
Minix Bolt
69x
Dia. 8 x 30mm
E
Wooden Dowel
38x
#10 x 16mm
F
Tapping Screw
16x
M4 x 38mm
C
CSK Screw
10x
M6.3 x 40mm
B
Unita Screw
16x
M6 x 8mm
H
Euro Screw
6x
J
Nail Leg
26x
I
Nail Pin
2x
Dia. 8 x 50mm
A
Wooden Dowel

V1 2022.07
Page 5of 26
27x
Dia. 15 x 12mm
K
Minix Cam
4x
L
U Bracket
4x
M
L Bracket
1x
L - 752m
Q
Hanger
1x
M4
U
Allen Key
4 set x
14" (350mm)
O
Drawer Slide
9x
5/8”
N
Hinges
4 set x
14" (350mm)
P
Drawer Slide
Fixings (not to scale)
1x
L - 381m
R
Hanger
2x
D-16mm
T
Flat Washer
2x
1.2x15x32x75mm
S
L-Mounting
Bracket

V1 2022.07
Page 6of 26
Layout Parts on Soft Surface
BACK
PANEL
BACK
PANEL
BACK
PANEL
DRAWER
BOTTOM
x2
DRAWER
BOTTOM
x2
x2
x2
x2
x2
x2
x2
x2
x2

H
O
V1 2022.077
Page 7of 26
STEP 1
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK
8 x2 x

V1 2022.07
Page 8of 26
STEP 2
D
10 x
L
2 x

V1 2022.07
Page 9of 26
STEP 3
STEP 4
D
5 x
L
2 x
HO
8 x2 x
PLEASE ENSURE TO FIX THE SCREWS AS PER ABOVE POINTED HOLES
INSTRUCTION TO AVOID DISTORTION OF OVERALL LOOK OF PRODUCTS
SECOND HOLE
FRONT
TOP
BACK

STEP 5
STEP 6
V1 2022.07
Page 10 of 26
D
4 x
J
G
EB
2 x 4 x

STEP 7
STEP 8
V1 2022.07
Page 11 of 26
E
3 x
K
7 x

STEP 10
STEP 9
V1 2022.07
Page 12 of 26
B
2 x
E
6 x

STEP 11
V1 2022.07
Page 13 of 26
D
N
STEP 12
E
14 x
A
A
A
2 x
N
K
6 x

STEP 13
V1 2022.07
Page 14 of 26
D
G
M
O
STEP 14
E
18 x
K
6 x

STEP 15
STEP 16
V1 2022.07
Page 15 of 26
A
B
J
6 x
A
B
GM
8 x
4 x

STEP 17
V1 2022.07
Page 16 of 26
PLEASE INSERT
HANGER HERE
A
B
C
G
O
EB
6 x 8 x
1 x 1 x
R
Q

STEP 18
V1 2022.07
Page 17 of 26
B
C
I
26 x
6 x
G

STEP 19
V1 2022.07
Page 18 of 26
P
Q
R
G
5 x
18 x
F
9 x
N

STEP 20
V1 2022.07
Page 19 of 26
F
18 x
P
R
A. Lateral adjustment (Moving Door Left-Right)
by screw adjusting
B. Vertical adjustment (Moving Door Up-Down)
via slot in the mounting plate
C. Front-to-back adjustment (Spacing Door O
Carcas) by slacking the hinge arm mounting
screw

STEP 21
V1 2022.07
Page 20 of 26
T
2 x
S
2 x
F
2 x
Do not tighten