7
410
uma g
ossy
4 eng
31008-
2267-
151-1-4
19
ma
n.
m
20.09.2012
Making calls
Making external calls and ending
calls
External calls are calls using the public telephone net-
work.
~(Enter phone number) ¤c.
The number is dialled.(Or you can first press and hold
c[dialling tone] and then enter the number.) During
the call you can adjust the earpiece volume using t
and set the volume with q.
Ending a call/cancelling dialling:
Press the end call key a.
Accepting a call
The handset indicates an incoming call in three ways:
by ringing, by a display on the screen and by the flash-
ing accept/speaker key c.
Press the talk key cto accept the call.
When Auto Answer is activated, simply remove the
handset from the base/charger (see menu tree
¢P. 12).
Displaying the caller's number
The phone number of the caller is shown on the dis-
play; the caller's name is also displayed if the name
has been saved in the directory.
Prerequisites:
1 You have asked your network provider for the call-
er's number (CLIP) to be displayed on your hand-
set screen.
2 The caller has asked the network provider for his/
her number to be identified (CLI).
In the display you will see External call if you have not
requested Calling Line Identification, Withheld if the
caller has withheld CLI or Unavailable if CLI has not
been requested.
Notes on calling line display (CLIP)
By default, the number of the caller is shown in the
display of your Gigaset telephone. You do not have to
make any other settings on your Gigaset telephone.
However, if the caller's number is not displayed, this
can be due to the following:
uYou have not ordered CLIP from your network pro-
vider
uYour telephone is connected via a PABX or a router
with an integrated PABX (gateway) that does not
transmit all information.
Is your telephone connected via a PABX/gateway?
You can establish this by checking for an additional
device connected between your telephone and
home connection e.g., a PABX, gateway etc. In most
cases, simply resetting this device will remedy the sit-
uation:
¤Briefly disconnect the PABX power plug. Re-insert
the plug and wait for the device to restart.
If the caller number is still not displayed:
¤Check the CLIP settings of your PABX and activate
this function if necessary. In the user guide for the
device, search for the term "CLIP"(or an alternative
term such as "calling line identification", "phone
number transmission", "caller ID" etc.). If neces-
sary, contact the device manufacturer.
If this does not resolve the problem, it is possible that
your network provider does not provide the CLIP
service for this number.
Have you ordered the calling line display service
from your network provider?
¤Check whether your provider supports calling line
display (CLIP) and that the function has been acti-
vated for you. If necessary, contact your provider.
Additional information on this subject can be found
on the Gigaset homepage at:
www.gigaset.com/service
Using speaker mode
Switching between earpiece and speaker mode:
During a call, press the accept/speaker key dto acti-
vate or deactivate speaker mode. If speaker mode is
activated, the key is lit up.
During a call, use tto open the menu for setting the
speaker volume and use qto set the volume.
Muting
You can mute your handset during a call. Your caller
can no longer hear you.
Press the right-hand control key vduring the call to
activate/deactivate the function.
Making internal calls
Internal calls are free calls to other handsets that are
registered to the same base.
To make a call to other handsets, press
uu¤q( Select internal number of handset) or
~(Enter internal number directly) ¤OK, the
handset is called or
uu¤Call All ¤OK all handsets are called (alterna-
tively you can also press and hold the control key
uor press u¤P).
To end the call, press the end call key a.
