Gigaset AT-510 User manual

AT-510 IP phone user manual
AT-510 IP phone user manual
1 / 31

AT-510 IP phone user manual
I、AT-510 Feature.................................................................................................4
1. Appearance........................................................................................................................4
2. Interfaces...........................................................................................................................4
3. Electricity characteristic....................................................................................................5
4. Software............................................................................................................................5
5. Operating requirement ......................................................................................................6
6. Packing List.......................................................................................................................6
7. Installation.........................................................................................................................6
II、Web Configuration...........................................................................................7
1. Access Web setting page...................................................................................................7
2. Network.............................................................................................................................7
2.1、WAN Configuration.............................................................................7
2.2、LAN Config........................................................................................ 10
3. VoIP.................................................................................................................................10
3.1、SIP Config .......................................................................................... 10
3.2、Iax2 Config ........................................................................................ 13
4. Advance ..........................................................................................................................14
4.1、Stun ................................................................................................... 14
4.2、Digit map........................................................................................... 15
4.3、Call Service ........................................................................................ 16
4.4、Audio Settings .................................................................................... 17
4.5、Config Service .................................................................................... 18
Dial-Peer configuration...........................................................................................................19
Config Manage........................................................................................................................20
Update.....................................................................................................................................20
4.6、Web Update: .....................................................................................20
4.7、TFTP/FTP Update: ............................................................................. 21
4.8、Auto Provisioning ..............................................................................22
System Manage.......................................................................................................................23
4.9、Account Manage ................................................................................23
4.10、Phone Book .......................................................................................24
4.11、Syslog config ......................................................................................24
4.12、Time Set.............................................................................................25
4.13、Reboot ..............................................................................................26
III、Use keypad configure AT-510 IP phone.........................................................26
1. Keypad function..............................................................................................................26
2. Keypad Menu..................................................................................................................27
IV、POST Mode ...................................................................................................28
V、FAQ................................................................................................................29
2 / 31

AT-510 IP phone user manual
1. Why the settings vanish after reboot?.............................................................................29
2. How to use the dial rule?.................................................................................................29
3. How to use speed dial function？...................................................................................30
4. How to use Call Forward, Call Transfer and 3-way Conference calls？........................30
5. How to use set the IP type via keypad？.........................................................................31
3 / 31

AT-510 IP phone user manual
I、AT-510 Feature
1. Appearance
2. Interfaces
9Power: Output Power:12VDC,800mA.
9WAN: RJ45 port.
9LAN: RJ45 port.
4 / 31

AT-510 IP phone user manual
3. Electricity characteristic
9Speciality of electric: output 12V 500mA DC
9The network connects: 2 RJ45 connect, a WAN, a LAN
4. Software
9Sip 2.0 (RFC3261)
9IAX2
9STUN
9Jitter Buffer (200ms) VAD, CNC
9G7.11 a/u , G729 codec.
9DHCP client and server.
9Support inbound audio, RFC2833 and SIP info , DTMF transmission way
9SIP Call Forward、Call transfer、Call hold、Call waiting, 3-way Talking、Pickup、Join call、
Redial、Unredial、Call Park
9Hotline、DND(Do Not Disturb)、blacklist、call limitation、caller ID
9Dial-peer calling rule ，IP to IP call
9SIP server conference
9Phone book 500 records; answered call、missed call 100 for each
9Config server management for remote IP phone terminal
9Support HTTP、FTP TFTP updating the configuration and firmware
9Auto Provisioning
9Syslog
9Answering machine
9Support PPPoE，（ADSL，cable modem use for internet connecting）
9Support SNTP terminal
9LAN support DHCP server,DNS relay
9WAN/LAN support both bridge and router mode
9Support Telnet, WEB access to terminal
9Support admin/guest different level management
Explanation:
The letter “e” is the first letter of “environment: and “electronic”, The rim is a round with two
arrow , stands for recycle. The number 20 stands for the years of environment protection. Please
note the years of environment protection is not discarding year nor usage life
5 / 31

AT-510 IP phone user manual
5. Operating requirement
9Operation temperature: 0 to 40° C (32° to 104° F)
9Storage temperature: -30° to 65° C (-22° to 149° F)
9Humidity: 10 to 90% no dew
9Package
9Size:338×220×85mm
6. Packing List
9AT-510 IP phone
9Power adaptor (out put 12v ,500mA)
9Manual CD
7. Installation
Use ethernet cable to connect AT-510’s LAN port and your computer. Set your computer’s ip to the network
192.168.10.x or using dynamic obtain IP. Open your web browser and key in 192.168.10.1. Then you will see the
logon page of AT-510, the default username and password is admin/admin for administrator and guest/guest for
guest.
Set up page for VoIP use only:
Power
PBX
User
Internet
6 / 31

AT-510 IP phone user manual
II、Web Configuration
1. Access Web setting page
Enter AT-510 IP address in the web browser and press ENTER to go to the log on page, and key in
the username and password to accessAT-510 setting page.
Default username and password is:
Administrator: Username: admin password: admin
User: Username:guest Username: guest
This page shows the IP phone woking status. The network part shows the connection status of
WAN and LAN . VoIP part shows the SIP server connection status
2. Network
2.1、WAN Configuration
There are 3 ways to connect to the internet DHCP , Static and PPPoE , please choose one
according to your own situation
A、DHCP，the IP phone will get IP address from DHCP server , you do not have to fill in the
date of IP address , net mask etc , just choose DHCP and submit . Please refer to the below picture
7 / 31

AT-510 IP phone user manual
Parameters：
9Active IP：IP phone’s address
9Current Netmask：network netmask
9MAC Address：MAC of IP phone
9Current Gateway ：the IP address of the router
B、If your ISP provide you with the fixed IP address, please choose static and fill in the correct
information of IP Address、Netmask、Gateway、Primary DNS etc. If you do not know it please
refer to your ISP provider or network management stuff. The reference picture is as below
Parameters：
9Static IPAddress: fixed IP address
9Netmask: LAN netmask
9Gateway: Gateway IP address
9DNS Domain: imput DNS domain name if it’s provided
9Primary DNS: Primary DNS address
9Alter DNS: Alternative DNS address
C、when you use PPPoE to get IP address，please select “PPPoE”，and input ADSL account
8 / 31

AT-510 IP phone user manual
information as below picture：
Parameters：
PPPoE Server: sever name, if the ITSP have no special requirements , keep the ANY as default
Username: ADSL account user name
Password: ADSL account password
Attention：
1）After configuration setting please click “Apply” to effect the change
2）If the IP address is changed after effecting the configuration change , the webpage will lose
response former address, so you must get to the webpage with new address
3）If the LAN IP address is happened to be the same as WAN IP which is allocated from DHCP
server. The LAN IP address will be changed automatically by adding 1 at the last digital
9 / 31

AT-510 IP phone user manual
2.2、LAN Config
Parameter：
9LAN IP：config LAN static IP
9Netmask: LAN netmask
9DHCP Service: enable LAN DHCP Server , need to reboot to make it available.
9NAT: Network Address Traslation
9Bridge Mode: make the IP phone into switch mode , press Apply the IP phone will reboot
3. VoIP
3.1、SIPConfig
9Register Status: SIP server registration status, if succeed display Registered，or else display
Unregistered
9Server Address: SIP server address , support both IP address and domain name
9Server Port: SIP server port , default is 5060
10 / 31

AT-510 IP phone user manual
9Account Name：SIP account name
9Phone Number：SIP account phone number, if leave it as blank , no registration information
will be sent out
9Display Name：show the display name that you want to display on the phone of callee.
Support number and letter input
9Proxy Server Address：Normally the Proxy server is the same as SIP server. If they are
different then fill in the correct information that provided by ISP
9Proxy Server Port:
9Proxy Username:
9Proxy Password:
9Domain Realm: config SIP local domain. If the server does not have a special requirements
for the local domain of SIP terminal , the local domain can be the same as SIP server domain.
The user can also leave it as blank , the system will take SIP server domain as the demain
realm.
9Enable Register: Enable or disable registration
Advanced SIP setting
9Register Expire Time: register expire time, default is 600 seconds. AT-510 will auto
configure this expire time to the server recommended setting if it is different from the SIP
server.
9NAT Keep Alive Interval: Co-work with the Auto Detect Server, if Auto Detect Server is
enable, AT-510 will periodically detect if the SIP server is available according this setting.
9User Agent::
9Signal Key: Signal encryption Key:
9Media Key: voice stream encryption Key
9Local Port: Local SIP signal port，default as 5060
11 / 31

AT-510 IP phone user manual
9Enable Subscribe: Subscribe to the register to see the message leave for you such as voice
mail
9Enable Conference Num: conference ID
9Enable Keep Authentication: AT510 can support registration with authentication request to
be sent to sever together
9NAT Keep Alive: Some server’s registration interval time is very short. To config the time
here less than the default interval time of servers can keep the IP phone always being
connected to server.
9Enable Via rport: rport mechanism is used in LAN to keep the NAT connection between
devices in and out of the LAN
9Enable PRACK: enable the PRACK in SIP which is mainly used in special ring tone ,
recommend to keep the default setting
9Long Contact: enable Contact filed hold more parameters
9Click To Talk: use the PC to initial calling , need the support of special software
9Forward Type: The function of forwarding before answering
9Off：disable call forward
9Busy：forward to a certain number when this line is busy
9No answer：when no answer for a long time , forward this call to a certain number
9Always：All the incoming calls will be forwarded to a certain number
9For any forwarded call , there is the message in the IP phone
9Forward Phone Number: config the certain number that the call will be forwarded to
9Server Type: Choose the encryption way or server type
9DTMF Mode: config DTMF transmission mode
¾DTMF_RELAY
¾DTMF_RFC2833
¾DTMF_SIP_INFO
9Different ITSP provider use different mode.
9RFC Protocol Edition: config the SIP protocol edition. When the IP phone need to work with
some SIP1.0 gateway such as CISCO5300，need to choose RFC2543 here. Default is
RFC3261
9Transport Protocol: choose TCP/UDP
9Subscribe Expire Time: Subscribe information packet Expire Time:
9Conference Number: config certain Conference call number
9Signal Encode: enable signal encryption
9Rtp Encode: enable voice data encryption
9Enable Session Timer: enable rfc4028 to refresh the SIP sessions
9Answer With Single Codec: only answer the call with a certain Codec
9Auto TCP: enable TCP transmission protocol when the length of message exceed 1300 byte
9Enable URI Convert: convert # into %23 when sending URI
12 / 31

AT-510 IP phone user manual
3.2、Iax2 Config
9Above is the IAX server configuration page
9IAX Server Addr: Register address of public IAX server
9IAX Server Port: Register port of public IAX server，default port is 4569
9Account Name: Username of your SIP account (Always the same as the phone number)
9Account Password: Password of your IAX account.
9Local port: Signal port of local, default port is 4569
9
9Phone Number: Phone number of your IAX account
9Voice mail number: If the IAX support voice mail, but your username of the voice mail is
letters which you can not input with the ATA , then you use the number to stand for your
username
9Voice mail text: if IAX support voice mail, config the domain name of your mail box here.
9Echo test number: If the platform support echo test , and the number is test form , the config
the test number to replace the text format The echo test is to test the woring status of
terminals and platform
9Echo test text: echo test number in text format
9Refresh time: IAX refresh time
9Enable Register: enable or disable register
9IAX(Default Protocol): Set IAX 2 as the default protocol to initial the call ( not answering) ,
if not the system will choose SIP as default. But you can still use SIP by config the prefix in
dial plan
9Enable G.729: Using G.729 speech coding mandatory consultations
13 / 31

AT-510 IP phone user manual
4. Advance
4.1、Stun
9STUN NAT Transverse：STUN NAT Transverse status true or false
9STUN Server Addr: configure stun server address;
9STUN Server Port: configure stun server port default 3478
9STUN Effect Time: stun detect NAT type interval time .If NAT found a link inactive for
a certain time , it will close the link so you need to send a packet within a interval tome to
keep the link alive
9Local SIP Port：config local SIP port , default as 5060Use Stun：enable/disable SIP STUN
9Attention：SIP STUN is used for NAT transverse. When you config STUN server’s
addressand port (default 3478) and enable it, then you can use the normal SIP server to make
the IP phone transverse NAT
14 / 31

AT-510 IP phone user manual
4.2、Digit map
Digit map is a set of rules to determine when the user has finished dialing.
AT510 support below digital map:
9End With “#”: Use # as the end of dialing.
9Fixed Length: The call will be sent out automatically when the length of the number you dial
reach the fixed one. For example if you set number of 11 here , when you dial 11 digits the
call will be sent out immediately.
9Timeout: Specify the timeout of the last dial digit. The call will be sent after timeout
9Prefix: User define digital map:
9[ ] represents the range of digit, can be a range such as [1-4], or use comma such as [1,3,5],
or use a list such as [234]
9x represents any one digit between 0~9
9Tn represents the last digit timeout. n represents the time from 0~9 second, it is necessary.
Tn must be the last two digit in the entry. If Tn is not included in the entry, we use T0 as
default, it means system will sent the number immediately if the number matches the entry.
9Example:
¾[1-8]xxx All number from 1000 to 89999 will be sent immediately.
¾9xxxxxxx8 digits numbers begin with 9 will be sent immediately.
¾911 Number 911 will be sent will be immediately
¾99xT4 3 digits numbers begin with 99 with be sent after four seconds.
9Attention：The above configuration can exist at the same time. For example you enable # as
the signal of sending the call while set fixed length of 11. Either you press # before the
number reach 11 or dial 11 digital can send out the call
15 / 31

AT-510 IP phone user manual
4.3、Call Service
User configure the value add service such as hotline, call forward, call transfer, 3-way conference
call .etc in this page
9Hotline: configure hotline number. AT-510 immediately dials this number after hook-off if it
is set and the user can not dial any other number
9No Answer Time: no answer call forward time setting.
9No Disturb: DND, do not disturb, when there is an incoming call , the caller will get the
message that this line is not available , but you it has no affection when you make outgoing
call
9Ban Outgoing: Enable this to ban outgoing calls.
9Enable Call Transfer: call transfer
9Enable Call Waiting: call waiting
9Enable Three Way Call: 3 way conference call
9P2P IP Prefix: config P2P IP call prefix，for example , if you want to call the phone with IP
address of 192.168.1.119 , then you define 192.168.1 here, once you dial #119 you will make
call to that IP phone
9Auto Answer: Enable/disable auto answer function
9Accept Any Call: If this option is disable, AT-510 refuse the incoming call when the called
number is different from AT-510’s phone number.
9.
9Enable Voice Record: Enable/disable answering machine function. Please refer to Record
Function for detail.
9User-defined Voice: Use customized greeting message.
9Incoming Record Playing: simultaneously play the message when recording.
9Black List: incoming call in these phone numbers will be refused. It support below rules
¾You add a certain number in it , when this number call you , it will be refused
¾Use x to represent any number. For example , 4xx means any incoming call with 3 digital
and the first digital is 4 , will be refused
¾Any digital call with a certain head number , For example 6. means any incoming number
16 / 31

AT-510 IP phone user manual
with the 6 as the first number will be refused
9Limit List: outgoing calls with these phone numbers will be refused
¾You add a certain number in it , when the number you dial contain this number , it will be
refused
¾Use x to represent any number. For example , 4xx means any outgoing call with 3 digital
and the first number of 4 , will be refused
¾Any digital call with a certain head number , For example 6. means any outgoing call
number with the 6 as the first number will be refused
9Attention：black list and limit list max record is 10 pieces for each
4.4、Audio Settings
9First Codec：choose the codec in first priority , available choice are G.711A/u, G.729
9Second Codec：choose the codec in second priority
9Third Codec：choose the codec in third priority
9VAD：voice active detection. If enabled ，G.729 payload length can not be set over 20ms
9Handdown Time：Flashhook response time , minimum 200ms as default. if the flashhook was
pushed down for less than 200ms , this action will take no effect.
9Input Volume：handset speaker voice volume
9Output Volume：handset MIC volume
9Handfree Volume：handfree speaker output volume
9Ring Volume：ring tone volume
9G729 Payload Length：config G729 Payload length
17 / 31

AT-510 IP phone user manual
4.5、Config Service
9Config server is an independent IP phone configuration software which is installed in PC
9Register status：show the status of registration
9Server Address：config server IP address
9Account Name：config server account name
9Password：config server password
9Signal Encode：signal encryption
9Enable Register：Enable/Disable registration
18 / 31

AT-510 IP phone user manual
1. Dial-Peer configuration
This is the Dial-peer setting page , please refer to “How to make dial plan ?”for reference
19 / 31

AT-510 IP phone user manual
2. Config Manage
9Save Config: save current settings. If not save , any change on setting will lost after
rebooting
9Backup Config: Backup the config file, via point the right key of mouse-Æsave target
as….-Æwill pop a save window, then type the config file name in the File name(the file type
is text file)
9Clear Config: restore to default settings.
Notice: clear config in admin mode, all settings restores to factory default; clear config in guest
modem, all settings except sip, advance sip restore to factory default.
3. Update
4.6、Web Update:
Update IP phone’s settings or firmware. Firmware file is .z extension when configure file is .cfg
extension,AT-510 will auto select configure update or firmware update according the extension.
20 / 31