Goodwe EHB Series User manual

EHB Series
Quick Installation Guide
Ver.1.0
2020-12-30

1
01 Safety and Warning
• Thedocumentationmaybeupdatedfromtimetotimeduetoproductupgradesorother
reasons.Unlessotherwisespeci󽗉ed,informationinthedocumentationdonotreplacesafety
cautionsinthelabels.Alldescriptionsinthedocumentationareusedforguidanceonly.
• Pleasereadtheusermanualcarefullytoacquireknowledgeaboutproductfeaturesand
safetyprecautionsbeforeinstallingtheequipment.GoodWewillnotbeliableforany
equipmentdamagesorpersonnelinjuriescausedbyfailuretoinstall,operateorcon󽗉gure
theinverterinaccordancewiththisdocumentorcorrespondingusermanual.
• Pleasefollowlocallawsandregulations,andsafetycautionsinthismanualduringthe
installation,operation,andmaintenance.Improperoperationormisusemayresultin
personalinjuriesorpropertylosses.
• Allinstallation,operation,andmaintenancemustbecarriedoutbytrainedprofessionals
whomeetthefollowingrequirements:
• readthroughthismanual
• befamiliarwithvarioussafetyprecautions
• operateproperly
• acquaintwithlocallaws,regulations,andstandards.
• Toensuresafety,pleaseuseinsulatedtoolsandwearpersonalprotectiveequipmentwhen
operatingtheequipment.
• Alwayscomplywithelectrostaticprotectionrules.Toprotecttheinverterfrombeing
damaged,pleasewearanti-staticgloves,wriststrapandclotheswhentouchingprinted
circuitboardorotherelectrostaticsensitivecomponentsduringoperation.
• Powero󽗈theequipmentbeforeanycableconnectionorelectricaloperation.
• Residualhighvoltageexistsaftertheequipmentispoweredo󽗈.Toavoidelectricshock,please
waitfor5minutesfortheequipmenttodischargetosafevoltage.
• DonotplugorpullDC/ACterminalswhentheequipmentisrunning.
• PVnegative(PV-)andbatterynegative(BAT-)oninvertersideisnotgroundedbydefault.
ConnectingPV-orBAT-toEARTHisstrictlyforbidden.
General safety cautions
Operation Safety Precautions
• Destroyingthelabelswithoutauthorizationwillvoidtheguaranteeofcorrespondingmodules.
• Donotinstalltheinverterwhenitissnowingorraining.Ifyouhaveto,payattentiontothe
waterproofandmoisture-proofoftheinverteranddistributionbox.
• Avoiddrillingholesinwallswhichwithcablesinsideorontheback.
• ThepolarityofPVstringsorontheinvertercannotbeconnectedbyreversely,otherwise
invertercouldbedamaged.
• PVcablemustbetightlycrimpedintotheconnectors.

2
• Theequipmentcangethotduringoperation.Touchingthehotsurfacecanresultinburn
injuries.
• Makesurebatterybreakeriso󽗈andbatterynominalvoltagemeettheHybridInverter
speci󽗉cationbeforeconnectingbatterytoinverterandmakesureinverteristotallyisolated
fromPVandACpower.
• Iftheequipmentisnottobeinstalledimmediately,putitinsidetheoriginalpackagewiththe
desiccant.Iftheequipmentisunpackedbutnotputintouseimmediately,sealallunused
terminalportstopreventdustandwatervaporcorrosion.
• Pleasebecarefulagainstanyelectricshockorchemicalhazard.
• PleasefollowingCmentsandstepsbellowstrictly.Useimproperwiremaycausebadcontact
andhighimpedance,whichisdangeroustothesystem.
• Theequipmentdamagecausedbyfollowingreasonsarenotcoveredbywarranty:
• Exceedtheguaranteeperiod.
• Improperinstallation,alteration,transportationoroperation.
• Theinstallationoroperationenvironmentisbeyondtherequirementsofthismanualorlocal
lawsandregulations.
• Forcemajeure(lightening,earthquake,󽗉redisaster,stormorvolcaniceruptionetc.)
• Unauthorizedreplacement,dismantle,maintenanceormodi󽗉cationofsoftwarecode.
• Failuretocomplywithlocallawsandregulations,andsafetyprecautionsinthismanual.
Formorewarrantyconditions,pleasevisitwww.goodwe.com.
Warranty Declaration

3
1 432 5 6
7 8 9
11 14
10 1213
02 Product Introduction
1.PVinputport
3.BMSport
5.METERport
7.DREDcommunicationport
9.BACK-UPport
11.Indicator
13.DCswitch
2.Batteryinputport
4.WiFi/Bluetoothport
6.ON-GRIDport
8.RS485port
10.WiFiResetButton
12.Bypassswitch
14.Breaker
03 Installing the Inverter
Packing List
Smart Meter*1
&CT*1
Wall-Mounted
Bracket*1
Wall-Mounted
Bracket*1 6-Pin Terminal*2
Positive PV
Plug
[1]
Negative PV
Plug
[2]
Positive BAT
Plug*1
Negative BAT
Plug*1 WiFi module*1 Locating Plate*1
Inverter *1
Straight
Screwdriver
*1
On Grid AC Plug*1
BACK-UP Plug*1
PE terminal*1 Documentation
[3]
WiFi module
Disassemble
Tool*1
Fixed Screw*4
or or
Expansion
Bolts
*7
Bluetooth
module*1
[1],[2]:SuppliedaccordingtoPVportnumbers.
[3]:IncludingQuickInstallationGuide,UserManual,etc.

4
140 mm
106 mm
120
182 mm
120 110
192 mm
415 mm
791 mm
150 mm 395 mm
175 mm
Dimension
Angle Space
15°
200mm
300mm
500mm
200mm
300mm

5
04
Installing the Inverter
1. Drillholeswiththehelpofinstallationlocatingplate.
2. Installthewall-mountedbracket.
3. Installtheinverter.
4. Securetheinverterwithalock.
5. Ensurethattheswitchison"OFF"positionandlockedduringinstallationandmaintenance.
(ApplicableinAustraliaandNewZealand)
12
5
Φ8mm
M5
4
3
Level

6
04 Electrical Connections
Overview of Cable Connections
To Smart
Meter Cable
Smart Meter
Power Meter
......
To Battery Cable
PE
PV Strings
Grid
ON-Grid
Load
Back-Up Load
Battery
AC Breaker
AC Breaker
Model PV Cable BAT Cable AC Cable PE Cable
GW5000-EHB 3-4mm² 12-13mm² 5-6mm² 5-6mm²
GW6500-EHB 3-4mm² 12-13mm² 8-10mm² 8-10mm²
GW8600-EHB 3-4mm² 12-13mm² 10-12mm² 10-12mm²
GW0010-EHB 3-4mm² 12-13mm² 10-12mm² 10-12mm²
CableSpeci󽗉cations
TheACbreakerspeci󽗉cation
dependsonactualloads.
Connecting the PE cable
PleaseconnecttheCT
fromHouse(K)toGrid(L).

7
Connecting PV Cables
Click
1 2
3
Connecting Battery DC Cables
7mm
7mm VACONN series
Click
1 2
3
1. Use the right plugs in the accessory box. Prepare cables and plugs.
2. Connect cables to connectors.
3. Screw the cap on and plug onto inverter side.
1. Use the right plugs in the accessory box. Prepare cables and plugs.
2. Connect cables to connectors.
3. Screw the cap on and plug onto inverter side.

8
Connecting AC Cables
ACcircuitbreakersshallbeinstalledonthegridsideandtheloadside.SelecttheACbreaker
accordingtotheactualload.
1. Prepare the terminals and AC cables.
2. Put AC cable through terminal cover and screw the three cables tightly on the connectors.
3. Lock terminal cover and screw up the terminal cap.
4. Connect the assambled AC terminals onto inverter.
Φ: 13-22mm
10-15mm 12-14mm
1 2
Make sure terminal
cover is locked up here.
3 4
ACbreaker
ACbreaker
Loadbreaker Loadbreaker
Connecting Communication Cables of Smart Meter and Installing CT
• CT cable is 3m as default, could be extended to max 5m.
• Choose standard network cables and RJ45 terminals only for
communication.
• Communication cables of Smart Meter can expand to 100m to ensure
normal communication. Normally.

9
1 2 3
45
1
2
BMS Meter
BMS Meter
1 2 3 4 5 6 7 8
DRED and Remote Shutdown Connection
NO. DRED port de󽗉nition Reserved port de󽗉nition RS485 port de󽗉nition
1 DRM1/5 CANL2 RS485_B2 [2]
2 DRM2/6 CANH2 RS485_A2 [2]
3 DRM3/7 GND-S LG_EN- [3]
4 DRM4/8 12V-S LG_EN+ [3]
5 REFGEN/Remote Shutdown[1] NODE- RS485_B1[4]
6COM/DRM0/Remote
Shutdown[1] NODE+ RS485_A1[4]