Gooxi SR201 2U User manual

SR201 2U
Rack Server User Manual
Document Version: 02
Release Date: 16/Nov/2022
Shenzhen Gooxi Information Security Co., Ltd.

Statement
Copyright Statement
©Shenzhen Gooxi Information Security Co., Ltd. All rights reserved.
This user manual, including but not limited to all information contained in it,
is protected by copyright law. Without the permission of Shenzhen Gooxi
Information Security Co., Ltd. (hereinafter referred to as "Gooxi"), no imitation,
copying, excerpt, forwarding and other acts or for other purposes.
Disclaimer
Gooxi provides this user manual on an "status quo" basis, and within the
scope of the law, does not provide any express or implied guarantees and
guarantees, including but not limited to commercial sales, suitability for specific
purposes, non-infringement of any rights of others and any guarantee of the use
of this user manual or the inability to use this user manual, and Gooxi does not
provide guarantees for the results obtained from the use of this manual or the
accuracy or reliability of any information obtained through this manual.
Due to the version upgrades or other reasons, the content of this manual
maybe be updated from time to time. Unless otherwise agreed, this manual is
only used as a guide, and the user shall bear all risks of using this user manual.
Trademark Statement
Gooxi®is a trademark of Shenzhen Gooxi Information Security Co., Ltd.
Microsoft®and Windows are trademarks of the Microsoft group of
companies.
Linux®is a registered trademark of Linus Torvalds.
Aspeed®is a trademark of Aspeed Technology Inc.
Other trademarks are the property of their respective owners.

Foreword
This manual is the product technical manual of Gooxi SR201 2U
rackmount server, which mainly describes the appearance, structure, hardware
installation and basic configuration of this product.
This manual is for reference and research by professional technicians. This
product should only be installed and maintained by experienced technicians.
Convention:
Note: it is used to transmit equipment or environmental safety warning
messages, if not avoided, it may lead to equipment damage, data loss,
equipment performance degradation or other unpredictable results.
Warning: indicates a potentially hazardous situation which, if not
avoided, it may result in death or serious personal injury.
Red arrow: means pointing to a certain location.
Blue arrows: means the action of pulling out or inserting at an angle.
Dark blue rotation arrow 1: represents the action of turning the screw
clockwise or pulling it outward.
Dark blue rotating arrow 2: represents the action of turning the screw
counterclockwise or buckling inward.
Hollow arrow: represents the next action or result.

Modification record
Manual version
Release date
Remarks
01
2022/October/16
Initial release
02
2022/November/16
Optimized description

Contents
1 Product Description ...................................................................................................................................................1
1.1 Product overview .......................................................................................................................................... 1
1.2 Product structure ........................................................................................................................................... 3
1.3 Logical structure ........................................................................................................................................... 3
1.4 Product parameters ....................................................................................................................................... 4
2 Hardware Description ............................................................................................................................................... 6
2.1 Front panel.................................................................................................................................................... 6
2.1.1 Appearance ................................................................................................................................................ 6
2.1.2 LED and button ..........................................................................................................................................7
2.1.3 Interface ..................................................................................................................................................... 8
2.2 Rear panel ..................................................................................................................................................... 9
2.2.1 Appearance ................................................................................................................................................ 9
2.2.2 LED and button ..........................................................................................................................................9
2.2.3 Interface ................................................................................................................................................... 10
2.3 Processor .....................................................................................................................................................11
2.4 Memory .......................................................................................................................................................11
2.4.1 Memory slot location ............................................................................................................................... 11
2.4.2 Memory compatibility information ......................................................................................................... 12
2.5 Storage ........................................................................................................................................................ 13
2.5.1 Hard disk configuration ........................................................................................................................... 13
2.5.2 Hard disk serial number ...........................................................................................................................15
2.5.3 Hard disk status LED ...............................................................................................................................15
2.6 Power supply .............................................................................................................................................. 16
2.7 Fan .............................................................................................................................................................. 16
2.8 I/O expansion ..............................................................................................................................................17
2.8.1 PCIe slot distribution ............................................................................................................................... 17
2.8.2 PCIe slot description ................................................................................................................................18
2.8.3 PCIe expansion module ........................................................................................................................... 19
2.9 PCBA .......................................................................................................................................................... 21
2.9.1 Motherboard............................................................................................................................................ 21
2.9.2 Hard disk backplane ................................................................................................................................ 23
3 Installation Notes .................................................................................................................................................... 27
3.1 Chassis upper cover installation................................................................................................................. 27
3.2 Mounting accessories ..................................................................................................................................27
3.2.1 Install the CPU .........................................................................................................................................27
3.2.2 Install heat-sink ........................................................................................................................................29
3.2.3 Install memory ......................................................................................................................................... 30
3.2.4 Install the server rails ...............................................................................................................................31
4 Configuration Instructions ...................................................................................................................................... 34
4.1 Initial configuration .................................................................................................................................... 34
4.1.1 Power on .................................................................................................................................................. 34
4.1.2 Initial data ................................................................................................................................................ 36
4.1.3 Configure BIOS ....................................................................................................................................... 36
4.1.4 Configure BMC ....................................................................................................................................... 37
5 Appendix ................................................................................................................................................................. 41

1
1Product Description
1.1 Product overview
The SR201 2U rackmount server is a new generation of 2U dual-socket rack server with
a wide range of uses launched by Gooxi for the needs of the Internet, IDC (Internet Data
Center), cloud computing, enterprise market, and telecom business applications. It is suitable
for IT core business, cloud computing virtualization, high-performance computing,
distributed storage, big data processing, enterprise and telecom business applications and
other complex workloads. The server has the advantages of low energy consumption, strong
scalability, high reliability, easy management, easy deployment, etc.
The main configurations are:
·Support 2 AMD EPYC™ 7003/7002/7001 processors.
·Support 3 types of panel frame: ①8*3.5-inch hard disk frame; ②12*3.5-inch hard disk
frame; ③25*2.5-inch hard disk frame.
·The rear window supports expansion of 4*3.5-inch hard disk bays and 4*2.5-inch hard
disk bays or 8*2.5-inch hard disk bays.
·Support up to 11 PCIe expansion slots, which can be used to expand GPU cards,
network cards, etc.
1SR201-D08R (Figure 1-1)
2SR201-D12RE (Figure 1-2)

2
3SR201-D25RE (Figure 1-3)
11-PCIe expansion rear window (Figure 1-4)

3
1.2 Product structure
The physical structure of the SR201 2U rack-mounted server is different due to different
requirements, and the configuration will be different. Taking the SR201-D12RE model as an
example, describe the components of the server, as shown in the figure below:
Structure diagram (1-5)
Table (1-1)
1.3 Logical structure
The logic of SR201 2U rack server is shown in the figure below:
S/N
Name
S/N
Name
1
Hard disk backplane
combination
8
Redundant power supply
2
Hard disk holder module
9
Rear 2.5 inch hard disk module
3
Upper cover
10
Wind shield
4
Fan module
11
Motherboard (G1DLRO-B)
5
Fan bracket
12
OCP3.0 network card (optional)
6
Full-height PCIe module
13
CPU heat-sink
7
Half-height PCIe module
14
Memory

4
Motherboard logic block diagram (1-6)
·2 SP3 Sockets, supporting two AMD EPYC™ 7002 series processors;
·Single CPU supports 8 DDR4 channels, each channel supports 2 DIMMs, and the two CPUs
support 32DIMM DDR4 memory;
·DDR4 type: DDR4 2400/2666/2933/3200MHz ECC-RDIMM/LRDIMM;
·There are 3 groups of PCIe RISER slots on the board, among which: 32 PCIE LANEs of
RISER1 come from CPU0, 32 PCIE LANEs of RISER2 come from CPU1, 16 PCIE LANEs of
RISER3 come from CPU1;
·G1DLRO-B motherboard provides 2 M.2 Key M SSD slots, only supports 2280 size, PCIe X2
signal;
·2 Gigabit Ethernet ports are integrated on the motherboard, using I350-AM2 chip;
·The BMC chip in this board adopts ASPEED company's AST2500 control chip, which is used
for IPMI remote management, VGA output port, and dedicated Gigabit RJ45 management
network port.
1.4 Product parameters
System
System model
SR201-D08R
SR201-D08R-NV
SR201-D12R
SR201-D12RE
SR201-D12R-NV
SR201-D25RE

5
Chassis
Gooxi®2U rackmount chassis
Motherboard
G1DLRO-B
CPU
Support 2 AMD EPYC™ 7003/7002/7001 processors
Memory
Type supports DDR4 RDIMM/LRDIMM;
Frequency supports 2400/2666/2933/3200MHz;
Support single capacity of 8G/16GB/32GB/64GB/128GB/256GB, and the
maximum memory capacity of the whole machine is 8TB.
Hard drive
Front 8* 3.5 or 2.5
inch hot-swap hard
drives
Front 12* 2.5 inch
hot-swap hard drives
Front 25* 2.5 inch
hot-swap hard drives
The rear supports four 3.5-inch or four 2.5-inch hot-swap hard drives
Internet function
2 RJ45 Gigabit Ethernet ports
Management
interface
1 RJ45 IPMI management network port
Display function
Onboard Aspeed ®AST2500 chip, support VGA output
M.2
Support 2 M.2 ports (M key, only support 2280 size specifications)
USB
Front 2 USB3.0 interfaces, built-in 1 USB3.0, rear USB3.0 interface
Expansion slot
Support up to 11 PCIE expansion slots
Power
System supports 550W, 800W, 1200W, 1300W, 1600W hot-swap
redundant power supply
Fan
The system supports four 8038 temperature-controlled fans (8056
temperature-controlled fans are optional)
Size
748mm*433.4mm*87.6mm (length*width*height)
Operating system support
OS
CentOS 7.6/ CentOS 8.0
SLES11 SP4
Ubuntu 17.04/Ubuntu 18.04/Ubuntu 20.04
Windows server 2016/Windows server 2019
VMware ESXi vSphere6/VMware ESXi vSphere7
System environment parameters
Operating
temperature and
humidity
Temperature 5℃ ~ 40℃; Humidity: 35% ~ 80% non-condensing
Storage
temperature and
humidity
Short time (≤72 H): temperature -40℃～70℃/ Humidity 20%～90%
non-condensing (including packaging)
Long time (>72 H): temperature 20 ℃～28℃/ Humidity 30%～70%
non-condensing (including packaging)
Certification
Certification
CE, CCC, ROHS
Table (1-2)

6
2Hardware Description
2.1 Front panel
2.1.1 Appearance
8x3.5 inch hard drive configuration
Figure (2-1)
S/N
Name
S/N
Name
1
DVD drive
3
USB3.0 interface
2
VGA interface
4
3.5 inch hard drive
Table (2-1)
12x3.5 inch hard drive configuration
Figure (2-2)
S/N
Name
S/N
Name
1
3.5 inch hard drive
3
USB3.0 interface
2
VGA interface
Table (2-2)
25x2.5 inch hard drive configuration
Figure (2-3)
S/N
Name
S/N
Name
1
2.5 inch hard drive
3
USB3.0 interface

7
2
VGA interface
Table (2-3)
2.1.2 LED and button
Figure (2-4)
S/N
LED/button
S/N
LED/button
1
Gooxi logo
5
Hard drive LED
2
Power switch button/LED
6
System alarm LED
3
UID button/LED
7
Network port 1 connection
status LED
4
Reset server button
8
Network port 2 connection
status LED
LED status description
Logo
LED/button
Status description
Power LED
Description of the power LED:
Green on: Indicates that the device has been
powered on normally.
Green flashing: Indicates that the device is in
standby.
Green off: Indicates that the device is not
powered on.
Power button description:
Press the button shortly in the power-on
state, and the OS will shut down normally.
Press and hold the button for 6 seconds in the
power-on state to force the server to power
off.
Press the button shortly in the power-on state
to start the machine.
UID
button/LED
The UID button/LED is used to conveniently
locate the server to be operated, and the LED
can be turned off or on by manually pressing
the UID button or remotely controlling the
BMC command.
Description of UID LED:
Blue (on/flashing): Indicates that the server

8
is located.
Off: Indicates that the server is not located.
UID button description: Short press this
button to turn on/off the positioning light.
Reset restart
server button
Press to restart the server
HDD LED
Green flashing: The hard disk is operating
normally
System
Alarm LED
System warning LED. Including system
alarms, fan alarms, power supply alarms,
etc., which can be viewed through the IPMI
management software
Network port
connection
status LED
Corresponds to the Ethernet port LED of the
network card.
Green on: Indicates that the network port is
connected normally.
Off: Indicates that the network port is not in
use or faulty.
Note: Corresponds to two 1GE network ports
on the motherboard.
Network port
connection
status LED
Corresponds to the Ethernet port LED of the
network card.
Green on: Indicates that the network port is
connected normally.
Off: Indicates that the network port is not in
use or faulty.
Note: Corresponds to two 1GE network ports
on the motherboard.
Table (2-4)
2.1.3 Interface
Interface location
Figure (2-5)
S/N
Name
S/N
Name
1
VGA interface
2
USB 3.0 interface

9
Table (2-5)
Interface description
Name
Type
Amount
Description
VGA
interface
DB15
1
For connection to a display terminal,
such as a monitor or KVM
USB
interface
USB 3.0
2
For accessing USB devices
Table (2-6)
2.2 Rear panel
2.2.1 Appearance
Appearance of the rear panel
Figure (2-6)
S/N
Name
S/N
Name
1
Riser 1 module
2
Riser 2 module
3
Riser 3 module
4
Riser 4 module
5
OCP network card
(optional)
6
PSU0
7
PSU1
-
-
Table (2-7)
Description:
1. Riser1 module, Riser2 module, Riser3 module, Riser4 module can choose
rear hard disk module or PCIe Riser module.
2. This picture is for reference only, the actual configuration shall prevail.
2.2.2 LED and button
Rear panel LED
Figure (2-7)
S/N
Name
S/N
Name
1
Management network port data
2
Management network port

10
transmission status LED
connection status LED
3
Network port data transmission
status LED
4
Network port connection
status LED
5
Restart button
6
Power module LED
Table (2-8)
Description of power module LED
LED/button
Status description
Power module
LED
Green on: Indicates that the input and output are
normal.
Orange on: Indicates that the AC power cord is
unplugged or the power module is lost, and only one
parallel-connected power module has AC input; the
power module failure causes the output to be turned
off, such as OVP, OCP, fan failure, etc.
Green (1Hz/flashing): Indicates that the input is
normal, that the input is normal, the voltage is too low
(less than 12V) or the power supply is in the smart open
state.
Green (2Hz/flashing): Indicates that the Firmware is
being upgraded online.
Orange (1Hz/flashing): Indicates a power supply
warning event that the power supply continues to run,
high temperature, high power, high current
Off: Indicates no AC power input.
Table (2-9)
2.2.3 Interface
Rear panel interface
Figure (2-8)
S/N
Name
S/N
Name
1
Management network port
2
VGA interface
3
Gigabit Ethernet port
(Onboard Ethernet port 1)
4
Gigabit Ethernet port
(Onboard Ethernet port 2)
5
COM interface
6
USB 3.0 interface
7
Power module interface
-
-
Table (2-10)

11
2.3 Processor
Supports 2 AMD EPYC™ 7003/7002/7001 processors.
When configuring 1 processor, it needs to be installed in the CPU 0 position.
Processors configured on the same server must have the same model.
For specific optional purchasing system options, please consult Gooxi sales rep.
The location of the processor is shown in the figure below:
Figure (2-9)
2.4 Memory
2.4.1 Memory slot location
The motherboard supports 8 DDR4 channels, each channel supports 2 DIMMs, and 2
CPUs support 32 DDR4 slots in total (when only one memory is inserted, insert the blue slot
on the motherboard first).
Memory slot location

12
Figure (2-10)
2.4.2 Memory compatibility information
The motherboard supports DDR4 RDIMM/LRDIMM server memory, and the memory
frequency supports 2400/2666/2933/3200;
Notice:
The same server must use the same type of DDR4 memory, and all memory must
run at the same speed, and the speed value is the lowest value of the following
items:
Memory speed supported by a particular CPU.
Maximum operating speed for a specific memory configuration.
Different types (RDIMM, LRDIMM) and specifications (capacity, bit width, rank,
height, etc.) do not support mixed use.
The maximum memory capacity supported by different models of AMD EPYC
CPUs is different. (See attachment-AMD CPU memory installation guide for
details)

13
Note:
1: M1 can be inserted in any slot, C or D is recommended.
2: M1, M2 can be inserted in any slot, C or G is recommended.
3: M1 can be in any slot, M2 can be inserted in any other slot.
4: M1 ≠ M2; M2 ≠ M3; M3 ≠ M4.
2.5 Storage
2.5.1 Hard disk configuration
Configuration
Max no. of front hard
disks (piece)
*Max no. of rear hard disks (piece)
Description

14
8x3.5 inch hard
drive pass-thru
configuration 1
Front hard drive
supports eight
3.5 inch or 2.5
inch SAS/SATA
hard drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4 2.5 -inch NVM e/
SAS / SATA hard drives
SAS hard drives need to
be equipped with SAS
pass-through card or
RAID card.
8x3.5 inch hard
drive pass-thru
configuration 2
Front hard drive
supports eight
3.5 inch or 2.5
inch SAS/SATA/
NVMe hard
drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4* 2.5 inch
NVMe/SAS/SATA hard drives
NVMe hard drives need
to be equipped with
Retimer card.
SAS hard drives need to
be equipped with SAS
pass-through card or
RAID card.
12x3.5 inch
hard drive
pass-thru
configuration 1
Front hard drive
supports 12* 3.5
inch or 2.5 inch
SAS/SATA hard
drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4* 2.5 inch
NVMe/SAS/SATA hard drives
SAS hard drives need to
be supported by
optional SAS
pass-through card or
RAID card.
12x3.5 inch
hard drive
pass-thru
configuration 2
Front hard drive
supports 12* 3.5
inch or 2.5 inch
SAS/SATA/
NVMe hard
drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4* 2.5 inch
NVMe/SAS/SATA hard drives
NVMe hard drives need
to be equipped with
Retimer card. SAS hard
drives need to be
equipped with SAS
pass-through card or
RAID card
12x3.5 inch
hard drive
EXP
configuration
Front hard drive
supports 12* 3.5
inch or 2.5 inch
SAS/SATA hard
drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4* 2.5 inch
NVMe/SAS/SATA hard drives
SAS pass-through card
or RAID card support is
required.
25x2.5 inch
hard drive
EXP
configuration
Front hard drive
supports 25* 2.5
inch SAS/SATA
hard drives
Riser 1/2 module supports
expansion of 4* 3.5 inch
SAS/SATA hard drives.
Riser 3/4 module supports
expansion of 4* 2.5 inch
NVMe/SAS/SATA hard drives
SAS pass-through card
or RAID card support is
required.
Note: *The maximum number of rear hard drives is affected by the type of NVMe /SAS/SATA
hard drives.
Table (2-10)

15
2.5.2 Hard disk serial number
8x3.5 inch hard drive configuration
Figure (2-11)
12x3.5 inch hard drive configuration
Figure (2-12)
25x2.5 inch hard drive configuration
Figure (2-13)
2.5.3 Hard disk status LED
Figure (2-14)
Hard Disk Status LED Description
Function
Act LED
Fault LED
Status LED
Hard disk in
place
On
Off
Off
Hard disk
activity
On
Off
Off
Hard disk
On
Flashing
Off