Grandview Large Stage Series User manual

Large Stage MBII Installation Manual
Model:LS-MBxxxII(xSxx)
Reminders
Thank you for purchasing Grandview products. Please read the instructions carefully before
installation and use, and collect it after reading for future use;
This product must be installed by a qualified professional after the feasibility asse sosfm ent
the environment, electricity, structure, etc.;
Do not disassemble or replace the original spare parts at will: If there is any fault, please
contact the after-sales service department.
Method for adjusting screen retracted height (upper limit)
and unfolding height (lower limit)
9 10 11
7 86
Up
Stop
Down
If due to installation environment or site limitations, it must adjust the limit height, It can bere b y alized
adjusting the motor button with a tool. Just remove the bezel on the power side to find the location of the motor.
Motor
Hexagon
adjustment hole
Pay attention
To confirm the accuracy and security of the screen position, It is necessary to control the screen up and down after
adjusting ever y half turn of the button, Check if the position is movin. g c o r rectly
Be careful when adjusting the screen retracted height. Excessive adjustment will cause the lower rod to snap into
the casing and cause serious damage to the screen or the lower rod falling!
Be careful when adjusting the unfolding height of the screen. Always keep the fabric 1.5 turns or more around the
tube to ensure that the fabric does not fall.
Electrical parameters Voltage AC220-230V/50-60Hz,Current 1.5A
Operation guidelines
1. Tear off the glue cloth fixed on the bottom rod, ensure the bottom rod is not stuck by the casing.
2. Connect to a power source (Please make sure it is the right voltage)
3. Turn the switch to position 2 to lower the screen; it will come down s l o w y . W h e n it is all the way down,
it will stop automatically.
Turn the switch to position 1 to lower the screen; it will go up into the metal casing. When it is all the
way up, it will stop automatically.
To stop any time while the screen is in motion, turn the switch to .
Automatic remote control (Please see section on Remote Control)
GRANDVIEW CRYSTAL SCREEN CO.LTD.
NO 43.S,Guomao Ave.Hualong,Panyu,Guangzhou,GuangDong.P.R.C
After sales service Tel:[phone]
This electric projection screen is divided into two ways: manual control power switch and remote control power
switch.(factory standard is manual control power switch)
Cut off the manual switch and replace it with an external remote control kit (see Figure 9-10). For the wiring method
and instructions of the remote control, please refer to the manual of the external remote control kit. For the package
size, see Figure 11.
Removing the bezel
Motor
Yellow button
Retracted height (upper limit)
Clockwise down
Counterclockwise up
White button
Unfolding height (lower limit)
Clockwise up
Counterclockwise down

Screen structure
Lower unit: mm
Accessories
Shackle (3)
Motorized adjust tool (3)Warranty Card (1)
Instruction manual (1)
Motor
exchange
port
Suspension installation
Measure the horizontal spacing of the hanging plate and the length of the product to determine the
installation position of the screen, and install three stable hooks on the solid concrete ceiling. Recommended
hook type is adjustable.
Concrete
ceiling
remain distance
on the left
>1000mm
Suspension
distance (P)
Hook
Hook the hook on the shackle of the left、middle and right hanging plate ,adjust the length of the hook to
the screen level, and complete the suspension installation
Hook
Load-
bearing Load- bearing
Anti-
dropping
Screw rod installation
Note: The default factory setting of this product is suspension installation. If the customer needs screw rod
installation, the installation method of the hanging plate can be converted!
Converting the hanging plate method: Remove the M10 screws and 8 nuts on the left and right hanging plate,
take out the hanging plate and turnover to the corresponding end caps and fasten with screw.
Turnover
Screw rod installation
Measure the spacing of the four oblong holes on the left and right hanging plate respectively. Install the
M12 screw rod directly above the corresponding hole to connect the left and right hanging plate, Install an
adjustable hook at the top of the screen to connect the middle hanging plate
Recessed installation (see photo to the right)
Load-
bearing Load- bearing
Anti-
dropping
Left hanging plate Middle Hanging plate Right Hanging plate
Casing
Fabric
rod