GREAT PLAINS 1510HDP User manual

Manufacturing, Inc.
www.greatplainsmfg.com
© Copyright 2018 Printed 2018-07-18 118-245M
EN
Table of Contents Index
Table of Contents Index
ORIGINAL INSTRUCTIONS
Operator Manual
1510HDP, 2010HDP and 2510HDP
15-, 20-, 25-Foot 3-Point Drills
with 10 Series Heavy Duty Precision Openers
Read the operator manual entirely. When you see this symbol, the
subsequent instructions and warnings are serious - follow without
exception. Your life and the lives of others depend on it!
Illustrations may show optional equipment not supplied with standard unit or
may depict similar models where a topic is identical.
27129

Machine Identification
Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new
manual.
If you or the dealer have added options not originally ordered with the machine, or removed options that were originally
ordered, the weights and measurements are no longer accurate for your machine. Update the record by adding the
machine weight and measurements with the option(s) weight and measurements.
Dealer Contact Information
Model Number
Serial Number
Machine Height
Machine Length
Machine Width
Machine Weight
Year of Construction
Delivery Date
First Operation
Accessories
Name:
Street:
City/State:
Telephone:
Email:
Dealer’s Customer
No.:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

1510HDP, 2010HDP and 2510HDP Cover Index Table of Contents
Great Plains | 118-245M | 2018-07-18 Cover Index iii
© Copyright 2008, 2009, 2013, 2018 All rights Reserved
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been
taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for
damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as
it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro,
Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.
Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone,
Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.
Brand and Product Names that appear and are owned by others are trademarks of their respective owners.
Printed in the United States of America
Table of Contents
Important Safety Information.................................................1
Safety Reflectors and Decals ............................................5
Introduction...........................................................................10
Document Family.............................................................10
Description of Unit ...........................................................10
Intended Usage ........................................................10
Models Covered .......................................................10
Using This Manual...........................................................10
Owner Assistance............................................................11
Preparation and Setup .........................................................12
Pre-Setup Checklist.........................................................12
Hitching............................................................................12
20- and 25-foot Hitching ...........................................12
15-foot Hitching ........................................................13
Electrical Connections .....................................................14
Hydraulic Hose Hookup (Options) ...................................15
Older Style Hoses with Color Ties............................17
Leveling the Drill ..............................................................18
Leveling: Single-Wheel.............................................19
Leveling: Offset-Single Wheel ..................................20
Leveling: Dual-Wheel ...............................................21
Options Setup..................................................................22
Acremeter Installation...............................................22
Seed Monitor Cab Module...............................................22
Speed Sensor Installation ........................................22
Hydraulic Console Installation .........................................23
Marker Setup ...................................................................24
Marker Chain Adjustment.........................................24
Marker Extension Setup ...........................................25
Marker Extension Adjustment ..................................25
Operating Instructions .........................................................26
Pre-Start Checklist...........................................................26
Prepare for Planting.........................................................26
Transporting ....................................................................27
Loading Materials ............................................................28
Seed Lubricants .......................................................29
Acremeter Operation .......................................................30
Normal Operating Sequence ...........................................30
Dormant Display ..............................................................30
Field Operation ................................................................31
Marker Operations...........................................................32
Independent Markers ...............................................32
Dual Auto-Sequenced Markers ................................32
Parking ............................................................................33
Storage ............................................................................33
Adjustments ..........................................................................34
Planting Depth.................................................................34
Material Rate Adjustments ..............................................35
Main Box Seed Rate ................................................36
Checking Main Box Seed Rate ................................38
Small Seeds Attachment Rate .................................42
Fertilizer Rate...........................................................45
Row Unit Adjustments .....................................................48
Unit-Mounted Coulter Adjustments ..........................49
Row Unit Down-Force ..............................................51
Row Unit Shutoff ......................................................53
Disk Blade Adjustments ...........................................57
Meter Adjustments ...................................................58
Seed Firmer Adjustments.........................................64
Press Wheel Adjustments ........................................65
Marker Adjustments ........................................................66
Marker Disk Angle....................................................66
Marker Speed...........................................................66
Hydraulic Drive Operation ...................................................68
Drive Operational Requirements .....................................68
Hydraulic System: ....................................................68
Electrical System:.....................................................68
Tractor Hookup................................................................68
Hydraulics: ...............................................................68
Electrical:..................................................................68
Controller Menu...............................................................69
Console Functions...........................................................70
Calibration .......................................................................70
Speed Calibration............................................................75
Operations.......................................................................77
Before going to the field ...........................................77
In Field .....................................................................77
Hydraulic Drive Calibration.......................................79
Varying Rates with Pre-set Function ...............................87
GPS-Based Planting .......................................................88
FarmWorks SiteMate ...............................................88
GP Precision Population Settings ............................88
Troubleshooting with SiteMate.................................89
Ag Leader PF3000 ...................................................90
Troubleshooting with PF3000 ..................................90
Hydraulic Drive Maintenance ..........................................92
To change the element: ...........................................92
Hydraulic Drive Troubleshooting .....................................93
Drive will not rotate:..................................................93
Drive rotates but not at desired speed: ....................94
Calibration Troubleshooting: ....................................95
Hydraulic Drive Troubleshooting Flow Chart...................96

1510HDP, 2010HDP and 2510HDP Cover Index Table of Contents
Great Plains | 118-245M | 2018-07-18 Cover Index iv
Hydraulic Drive Electronics Troubleshooting...................97
Troubleshooting ...................................................................98
Maintenance and Lubrication ............................................103
Materials Clean-Out.......................................................103
Main Seed Box Clean-Out......................................103
Small Seeds Box Clean-Out...................................103
Fertilizer Clean-Out ................................................104
Meter Maintenance........................................................105
Singulator Plus Meter Maintenance .......................105
Finger Meter Maintenance .....................................107
Row Unit Maintenance ..................................................109
Seed Tube Maintenance ........................................109
Grommet Maintenance...........................................109
Disk Spreader-Scraper...........................................110
Seed Flap Replacement.........................................110
Chain Maintenance........................................................111
Chain Slack ............................................................111
Idler Chain Tension ................................................111
Marker Maintenance......................................................112
Marker Shear Bolt ..................................................112
Marker Disk Grease Seal .......................................112
Bleeding Marker Hydraulics ...................................113
Marker Transport Carrier........................................114
Lubrication .....................................................................115
Options ................................................................................120
Accessory Hitches .........................................................120
Hitch Setback Kit ...........................................................120
Seed Monitor .................................................................121
Speed Sensors ..............................................................122
Hydraulic Meter Drive ....................................................123
Gauge Wheels...............................................................124
Weight Bracket Kit .........................................................124
Markers..........................................................................125
Seed Lubricants.............................................................125
Main Seed Box Baffles ..................................................126
Fertilizer.........................................................................127
Small Seeds ..................................................................128
Small Seed Tube Plugs .................................................128
Row Unit Options...........................................................129
10HD Series Seed Meters.............................................129
Row Unit Press Wheels.................................................131
Appendix .............................................................................132
Specifications and Capacities........................................132
Tire Inflation Chart .........................................................134
Torque Values Chart .....................................................135
Row Spacing Data.........................................................135
Hydraulic Diagrams .......................................................162
Chain Routing................................................................165
Warranty ........................................................................168

1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 1
Important Safety Information
Look for Safety Symbol
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention are
dependent upon the awareness, concern, prudence and
proper training of personnel involved in the operation,
transport, maintenance and storage of equipment.
Be Aware of Signal Words
Signal words designate a degree or level of hazard
seriousness.
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
This signal word is limited to the most extreme situations,
typically for machine components that, for functional
purposes, cannot be guarded.
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury, and includes hazards that are exposed when
guards are removed. It may also be used to alert against
unsafe practices.
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
Prepare for Emergencies
Be prepared if a fire starts
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctor, ambulance, hospital
and fire department near phone.
Be Familiar with Safety Decals
Read and understand “Safety Reflectors and Decals”
starting on page 5, thoroughly.
Read all instructions noted on the decals.
Keep decals clean. Replace damaged, faded and illegible
decals.

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 2
1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Avoid High Pressure Fluids
Escaping fluid under pressure can penetrate the skin,
causing serious injury.
Avoid the hazard by relieving pressure before
disconnecting hydraulic lines.
Use a piece of paper or cardboard, NOT BODY PARTS, to
check for suspected leaks.
Wear protective gloves and safety glasses or goggles when
working with hydraulic systems.
Hydraulic fluid injected under the skin is an extremely
serious matter. If such an accident occurs, seek urgent
medical attention from a physician familiar with this type
of injury.
Wear Protective Equipment
Wear protective clothing and equipment.
Wear clothing and equipment appropriate for the job.
Avoid loose-fitting clothing.
Because prolonged exposure to loud noise can cause
hearing impairment or hearing loss, wear suitable
hearing protection such as earmuffs or earplugs.
Because operating equipment safely requires your full
attention, avoid wearing entertainment headphones while
operating machinery.
Keep Riders Off Machinery
Riders obstruct the operator’s view. Riders could be
struck by foreign objects or thrown from the machine.
Never allow children to operate equipment.
Keep all bystanders away from machine when
folding/unfolding, raising/lowering markers,
raising/lowering openers, and transporting.
Use Safety Lights and Devices
Slow-moving tractors and towed implements can create
a hazard when driven on public roads. They are difficult
to see, especially at night.
Use flashing warning lights and turn signals whenever
driving on public roads.
Use lights and devices provided with the drill.

1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 3
Transport Machinery Safely
Maximum transport speed for drill is 20 mph (32 kph).
Some rough terrains require a slower speed. Sudden
braking can cause a towed load to swerve and upset.
Do not exceed 20 mph (32 kph) or the legal speed limit,
whichever is lower. Never travel at a speed which does not
allow adequate control of steering and stopping. Reduce
speed if towed load is not equipped with brakes.
Comply with national, regional and local laws.
Follow your tractor manual recommendations for
maximum hitch loads. Insufficient weight on tractor
steering wheels will result in loss of control.
Carry reflectors or flags to mark drill in case of
breakdown on the road.
Keep clear of overhead power lines and other
obstructions when transporting. Refer to transport
dimensions under “Specifications and Capacities” on
page 132.
Check for Overhead Lines
Drill markers contacting overhead electrical lines can
introduce lethal voltage levels on drill and tractor frames.
A person touching almost any metal part can complete
the circuit to ground, resulting in serious injury or death.
At higher voltages, electrocution can occur without direct
contact.
Avoid overhead lines during seed loading/unloading and
marker operations.
Handle Chemicals Properly
Agricultural chemicals can be dangerous. Improper use
can seriously injure persons, animals, plants, soil and
property.
Do not use liquid treatments with drill.
Read and follow chemical manufacturer’s instructions.
Wear protective clothing.
Handle all chemicals with care.
Avoid inhaling smoke from any type of chemical fire.
Never drain, rinse or wash dispensers within 100 feet
(30m) of a freshwater source, nor at a car wash.
Store or dispose of unused chemicals as specified by
chemical manufacturer.
Dispose of empty chemical containers properly. Laws
generally require power rinsing or rinsing three times,
followed by perforation of the container to prevent re-use.

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 4
1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Shutdown and Storage
Clean out and safely store or dispose of residual
chemicals.
Secure drill using blocks and transport locks.
Lock up openers.
Store in an area where children normally do not play.
Practice Safe Maintenance
Understand procedure before doing work. Use proper
tools and equipment. Refer to this manual.
Work in a clean, dry area.
Put tractor in park, turn off engine, and remove key before
performing maintenance.
Make sure all moving parts have stopped and all system
pressure is relieved.
Disconnect battery ground cable (-) before servicing or
adjusting electrical systems or before welding on drill.
Inspect all parts. Make sure parts are in good condition
and installed properly.
Remove buildup of grease, oil or debris.
Remove all tools and unused parts from drill before
operation.
Tire Safety
Tire changing can be dangerous and should be
performed by trained personnel using correct tools and
equipment.
When inflating tires, use a clip-on chuck and extension
hose long enough for you to stand to one side–not in front
of or over tire assembly. Use a safety cage if available.
When removing and installing wheels, use wheel-handling
equipment adequate for weight involved.

1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 5
Safety At All Times
Thoroughly read and understand the instructions in this
manual before operation. Read all instructions noted on
the safety decals.
Be familiar with all drill functions.
Operate machinery from the driver’s seat only.
Do not leave drill unattended with tractor engine running.
Do not dismount a moving tractor. Dismounting a moving
tractor could cause serious injury or death.
Do not stand between the tractor and drill during
hitching.
Keep hands, feet and clothing away from power-driven
parts.
Wear snug-fitting clothing to avoid entanglement with
moving parts.
Watch out for wires, trees, etc., when folding and raising
drill. Make sure all persons are clear of working area.
Safety Reflectors and Decals
Your drill comes equipped with all lights, safety reflectors
and decals in place. They were designed to help you
safely operate your drill.
Read and follow decal directions.
Keep lights in operating condition.
Keep all safety decals clean and legible.
Replace all damaged or missing decals. Order new decals
from your Great Plains dealer. Refer to this section for
proper decal placement.
When ordering new parts or components, also request
corresponding safety decals.
To install new decals:
1. Clean the area on which the decal is to be placed.
2. Peel backing from decal. Press firmly on surface,
being careful not to cause air bubbles under decal.
Slow Moving Vehicle Reflector
818-055C
reflector is mounted at center rear edge of walkboard(s);
1 total
27130

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 6
1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Red Reflectors
838-266C
Rear walkboard face, outside corner (all models),
rear walkboard face, center (2010HDP and 2510HDP);
2 or 4 total
Amber Reflectors (large)
838-265C
On outside end faces of walkboards at ladder top,
front top face of mainframe, each outside corner;
4 total
Amber Reflectors, small (Option)
818-229C
On front face of first section of marker;
1 total per marker
Daytime Reflectors
838-267C
Rear walkboard face, inboard of red reflectors;
2 (on 1510HDP) or
4 (on 2010HDP and 2510HDP) total
27130
27130
18270
27130

1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 7
Danger: Read Manual
848-512C
On tongue at hitch;
1 total
Danger: Crushing Hazard
818-590C
On front face of mainframe, right of 3-point hitch;
1 total
Warning: Excessive Speed Hazard
818-337C
On front face, top front of mainframe, above each gauge
wheel assembly;
2 total
Warning: High Pressure Fluid
818-339C
On front face of mainframe, right of 3-point hitch;
1 total
27130
848-512C
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
27130
27130
WARNING
EXCESSIVE SPEED
HAZARD
To Prevent Serious Injury or Death:
Do NOT exceed 20 mph maximum
transport speed. Loss of vehicle
control and/or machine damage
can result.
818-337C Rev. B
27130

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 8
1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Warning: Marker Pinch Crush (Option)
818-682C
On front and top faces, inner marker section,
2 per marker; 4 total
Warning: Falling Hazard
838-102C
On outside face of mainframe, forward of ladder;
2 total
Caution: Tires Not A Step
818-398C
On front face, top front of mainframe, above each gauge wheel assembly;
2 total
Caution: Read Manual
818-587C
On front face of mainframe, right of 3-point hitch;
1 total
18270
27130
WARNING
To avoid serious injury or death:
Watch your step when climbing ladder or
walking on walkboard.
838-102C
27130
27130
WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Read Owner’s Manual before usingmachine.
Stand clear when foldingand unfoldingmarkers.
Stand clear when raisingand loweringmachine.
Keep all safety shieldsand devicesin place.
Keep hands, feet, and clothingaway from
Never ride on machine.
Alwayslower or properly support machine
Escapinghydraulic fluid can cause serious
Review safety instructionswith all operators
movingchainsand sprockets.
BEFORE servicing.
818-587C Rev. B
injury.
annually.
CAUTION

1510HDP, 2010HDP and 2510HDP Table of Contents Index Important Safety Information
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 9
Caution: 32 PSI Tire Pressure
818-751C
On rim of each 9.5L-15-6ply wheel;
2 total
Caution: 52 PSI Tire Pressure
818-752C
On rim of each 11L-15SL-12ply wheel;
2 total
Caution: 36 PSI Tire Pressure
818-855C
On rim of each 11L-15SL-8ply wheel;
4 total
24379
27225
26216

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 10
1510HDP, 2010HDP and 2510HDP Table of Contents Index Introduction
Introduction
Great Plains welcomes you to its growing family of new
product owners. Your 3-Point Drill has been designed
with care and built by skilled workers using quality
materials. Proper setup, maintenance, and safe
operating practices will help you get years of satisfactory
use from the machine.
Document Family
Great Plains parts:
118-245M Operator Manual (this document)
118-245P 2510HDP Parts Manual
118-928P 2010HDP Parts Manual
119-949P 1510HDP Parts Manual
118-245B Seed Rate Manual
DICKEY-john parts:
11001-1359-200605Seed Monitor Manual
Description of Unit
The products covered by this manual are 15-, 20- and
25-foot 3-point mounted seed drills. They are equipped
with HD10 Series heavy duty row units and precision
seed meters.
Intended Usage
Use this implement to seed production-agriculture crops
in conventional or minimum tillage applications.
Models Covered
1510HDP-12TR15-Foot, 12-Twin Row (6 pair), 30in
1510HDP-131515-Foot, 13-Row, 15in
1510HDP-191015-Foot, 19-Row, 10in
1510HDP-19TRS15-Foot, 19-Row Twin Split
(6 pairs on 30in, plus 7 singles)
1510HDP-247515-Foot, 24-Row, 7.5in
2010HDP-16TR20-Foot, 16-Twin Row (8 pair), 30in
2010HDP-171520-Foot, 17-Row, 15in
2010HDP-251020-Foot, 25-Row, 10in
2010HDP-25TRS20-Foot, 25-Twin Row Split
(8 pairs on 30in, plus 9 singles)
2010HDP-327520-Foot, 32-Row, 7.5in
2510HDP-201525-Foot, 20-Row, 15in
2510HDP-20TR3025-Foot, 20-Twin Row (10 pair), 30in
2510HDP-291025-Foot, 29-Row, 10in
2510HDP-29TRS25-Foot, 29-Twin Row Split
(10 pairs on 30in, plus 9 singles)
2510HDP-407525-Foot, 40-Row, 7.5in
Using This Manual
This manual familiarizes you with safety, assembly, oper-
ation, adjustments, troubleshooting, and maintenance.
Read this manual and follow the recommendations to
help ensure safe and efficient operation.
The information in this manual is current at printing.
Some parts may change to assure top performance.
Definitions
The following are used throughout this manual.
Right-hand and left-hand as used in this manual are
determined by facing the direction the machine will travel
while in use unless otherwise stated.
Paragraphs in this format present a crucial point of
information related to the current topic.
Read and follow the directions to:
- remain safe,
- avoid serious damage to equipment and
- ensure desired field results.
Paragraphs in this format provide useful information
related to the current topic.
Figure 1
Left/Right Notation
18327
L
R

1510HDP, 2010HDP and 2510HDP Table of Contents Index Introduction
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 11
Owner Assistance
If you need customer service or repair parts, contact a
Great Plains dealer. They have trained personnel, repair
parts and equipment specially designed for Great Plains
products.
Refer to Figure 2
Your machine’s parts were specially designed and
should only be replaced with Great Plains parts. Always
use the serial and model number when ordering parts
from your Great Plains dealer. The serial-number plate is
located on the left side of the drill frame below the front of
the main seed box.
Record your drill model and serial number here for quick
reference:
Model Number:__________________________
Serial Number: __________________________
Your Great Plains dealer wants you to be satisfied with
your new machine. If you do not understand any part of
this manual or are not satisfied with the service received,
please take the following actions.
1. Discuss the matter with your dealership service
manager. Make sure they are aware of any problems
so they can assist you.
2. If you are still unsatisfied, seek out the owner or
general manager of the dealership.
For further assistance write to:
Product Support
Great Plains Mfg. Inc., Service Department
PO Box 5060
Salina, KS 67402-5060
785-823-3276
Figure 2
Serial Number Location
16490

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 12
1510HDP, 2010HDP and 2510HDP Table of Contents Index Preparation and Setup
Preparation and Setup
This section helps you prepare your tractor and drill for
use. Before using the drill in the field, you must hitch the
drill to a suitable tractor and also setup the drill.
Pre-Setup Checklist
1. Read and understand “Important Safety
Information” starting on page 1.
2. Check that all working parts are moving freely, bolts
are tight, and cotter pins are spread.
3. Check that all grease fittings are in place and
lubricated. “Lubrication” starting on page 115.
4. Check that all safety decals and reflectors are
correctly located and legible. Replace if damaged.
“Safety Reflectors and Decals” starting on page 5.
5. Inflate tires to pressure recommended and tighten
wheel bolts as specified. “Appendix” on page 132.
Hitching
You may be severely injured or killed by being crushed
between the tractor and drill. Do not stand or place any part of
your body between machines being hitched. Stop tractor and
set parking brake before inserting hitch pins.
20- and 25-foot Hitching
15-foot hitching is on page 13.
These instructions are for a direct 3-point hitch. If using
an optional CPH, PFH or SSH hitch (model 2010HDP
only), consult the hitch manual.
Hitch Setup (20/25ft)
Refer to Figure 3
1. For tractors with category III and III-N hitches,
position the center/upper pin in the bottom center
holes .
For tractors with category IV-N hitches, position the
center/upper pin in the upper center holes
2. Make sure the lower pins are in the bottom holes
of the lower hitch weldments, and that the spacers
are present.
Routine Hitching (20/25ft)
3. Make sure all cables and hoses are clear of the hitch
area.
Figure 3
25-foot 3-Point Hitch
27408
1
3
2
5
6
4
1
2
1
3
4
5
6

1510HDP, 2010HDP and 2510HDP Table of Contents Index Preparation and Setup
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 13
4. For a “quick hitch”, align lower arms with lower hitch
points, set spacers and engage lower arms.
For pinned hitch, remove pins and spacers, align
hitch arms and re-pin.
5. Slowly raise drill, watching for cab interference.
6. Adjust top link so that when in field position, top side
of drill mainframe is parallel to the ground.
Do not use 3-point link to adjust opener depth. See
“Planting Depth” on page 34 for a summary of depth
control settings.
7. Set tractor three-point draft control to Float.
8. Skip to “Electrical Connections” on page 14.
Raise Parking Stand (20ft)
Only the 15- and 20-foot drills have these stands (one on
each side). The stand is primarily needed when an
accessory hitch is used.
9. Make sure the drill raising at step 5 above has
removed all weight carried by the stands.
10. Remove the pins .
11. Slide the stand tube up in the sleeve (you may also
invert the tube, with the foot plate on top).
12. Re-insert the pin.
15-foot Hitching
20- and 25-foot hitching is on page 12.
These instructions are for a direct 3-point hitch. If using
an optional CPH, PFH or SSH hitch, consult the hitch
manual.
Hitch Setup (15ft)
Some tractor 3-points may require additional bushings
(not supplied by Great Plains) to adapt the pin diameters:
Upper Link: Qty 1, 1in ID x 114in OD
Lower Link: Qty 2, 118in ID x 1716in OD
Refer to Figure 5 and Figure 6
As supplied from the factory, 1510HDP hitches are set
for category II.
1. For tractors with category III and III-N hitches,
position the center/upper pin in the bottom center
holes .
For tractors with category IV-N hitches, position the
center/upper pin in the upper center holes
Figure 4
Raise Parking Stand
27410
7
7
Figure 5
15-foot Category II Hitch
27409
5
4
66
3
2
1
1
2
1
2

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 14
1510HDP, 2010HDP and 2510HDP Table of Contents Index Preparation and Setup
2. For tractors with category III hitches, remove all
lower pins ( and ) and re-position the pin
supports from their category II positions on the top
pins to their category III positions as shown in
Figure 6.
Routine Hitching (15ft)
Refer to Figure 5 and Figure 6
3. Raise or lower tractor three-point arms as needed
and pin lower arms to drill.
4. Pin upper arm to drill.
For category II, III and III-N tractors, install hitch pin
in the lower hole.
For category IV-N tractors, install hitch pin in the
upper hole.
5. Slowly raise drill. Watch for cab interference.
6. If drill has parking stands, pin them up. See page 13
for details.
7. Adjust top three-point link so that top edge of drill
box is parallel with ground when drilling.
Do not use link to adjust opener depth. For opener
adjustments, refer to “Leveling the Drill” on page 18
and “Adjustments” starting on page 34.
8. Set your tractor three-point-Control control to Float
position.
Electrical Connections
Refer to Figure 7
9. Plug drill electrical lead into tractor seven-pin
connector. If your tractor is not equipped with a
seven-pin connector, contact your dealer for
installation.
10. If the drill is equipped with the optional seed monitor,
mate the connector for the cab console.
See “Seed Monitor Cab Module” on page 22 for
installation.
See “Seed Monitor” on page 121 for ordering
information.
Figure 6
15-foot Category III Hitch
27409
77
4
5
6
7
Figure 7
Lighting Connector
36051

1510HDP, 2010HDP and 2510HDP Table of Contents Index Preparation and Setup
Great Plains | 118-245M | 2018-07-18 Table of Contents Index 15
11. If the drill is equipped with the optional hydraulic
meter drive, mate the connector for the cab console.
See “Hydraulic Console Installation” on page 23 for
installation.
See “Hydraulic Meter Drive” on page 123 for ordering
information.
12. If the drill is equipped with one or more speed
sensors (radar and.or magnetic) mounted on the drill
mate the connectors for the cab displays.
See “Speed Sensor Installation” on page 22 for
installation.
See “Speed Sensors” on page 121 for ordering
information.
Hydraulic Hose Hookup (Options)
Only trained personnel should work on system hydraulics!
Escaping fluid under pressure can have sufficient pressure to
penetrate the skin, causing serious injury. Avoid the hazard by
relieving pressure before disconnecting hydraulic lines. Use a
piece of paper or cardboard, NOT BODY PARTS, to check for
leaks. Wear protective gloves and safety glasses or goggles
when working with hydraulic systems. Hydraulic fluid injected
under the skin is an extremely serious matter. If such an
accident occurs, seek urgent medical attention from a
physician familiar with this type of injury.

Great Plains | 118-245M | 2018-07-18 Table of Contents Index 16
1510HDP, 2010HDP and 2510HDP Table of Contents Index Preparation and Setup
Refer to Figure 8
Great Plains hydraulic hoses have color coded handle
grips to help you hookup hoses to your tractor outlets.
Hoses that go to the same remote valve are marked with
the same color.
To distinguish hoses on the same hydraulic circuit, refer
to the symbol molded into the handle grip. Hoses with an
extended-cylinder symbol feed cylinder base ends.
Hoses with a retracted-cylinder symbol feed cylinder rod
ends.
For hydraulic fan and drive motors, connect the hose
under the retracted cylinder symbol to the pressure side
of the motor. Connect the hose under the extended
cylinder symbol to the return side of the motor.
These instructions presume a direct tractor-drill 3-point
hitching. If an accessory hitch is used, hose routing and
color coding may vary, and there will be one or two
additional circuits (for the hitch lift and tongue).
13. Connect meter drive hoses to tractor remote valve.
14. The optional hydraulic meter drive requires
continuous flow. If the tractor has only one circuit so
rated, or a priority circuit, use that circuit for the drive.
See “Drive Operational Requirements” on page 68
for circuit requirements.
15. Connect marker hoses to tractor remote valve.
16. If this is the first time the drill has been hitched, bleed
the marker hydraulics per the instructions on page
113.
Color Hydraulic Function
Green Marker Cylinders
Yellow Hydraulic Meter Drive
Figure 8
Color Coded Hose Grips
31733