GSM Activate AD-SD User manual

PAGE 1

Product Information
Our AD-SD Auto Dialler is a versatile unit which can be attached to many of your
electronic devices in your home; work, gardens or wherever you may need it. It will alert
you using GSM technology by sending a text message or phone call to your mobile phone
or landline. Therefore alerting you immediately to a problem, failure or status change
wherever you are in the world!
Our AD-SD-W (wireless) version has wireless capabilities making it a standalone alarm
using various wireless sensors.
These Auto Diallers are set apart from other models on the market by being on the quad
band frequency meaning they can be used worldwide and we frequently ship models all
over Europe, USA and Australia with excellent feedback.
The unit is also enclosed in an IP65 rated enclosure ensuring it is perfectly weathered for
outside installation and has passed testing in high heats and below freezing conditions.
Specification
● GSM Frequency: Quadband Freq 850/900/1800/1900 - 3G model 2100mhz
● Power Supply Voltage: 9 - 24 volts DC - 1 Amp Max
● Current used in standby mode: 60mA Max
● IP65 Rated Enclosure for outside installation
● 2 Inputs - Negative triggered
● 1 Input - Positive triggered
●8 Amp Relay Output
●Micro Simcard
●No landline needed
● Dimensions - L150 x W90 x H45mm
●Dimensions (PCB Only) - L125 x W67mm
● Sim Active Function
● Operating Temperature: -10…+40°C
● Programmed by Text/SMS Message
● Text to test signal strength
● 2G or 3G Model available
Wireless Function Model AD-SD-W (refer to page 8)
● Wireless Alarm Function
● Activate Alarm by text message
● RF 433mhz Transmission/Receiver … code EV1527
●Range 10 meters line of sight
Page 2

Page 3
Instructions
Slide the simcard into the holder ensuring that the clipped corner of the simcard lines up
with the clippd corner of the simcard holder (Illustrated above).
IMPORTANT - PLEASE READ
PLAESE ENSURE THAT YOU DISCONNECT THE POWER WHEN YOU FIT THE SIM
CARD THE PLACE THE SIMCARD WITH THE CLIPPED CORNER FACING INWARDS.
PLEASE SEE PICTURE ABOVE
Connect 9 through to 24 volts to the input connector as per figure 1. Once power has
been applied the blue network LED light will flash once every second. Once a signal has
been found the green LED will come on and stay on indicating the unit is now ready for
use.
Signal Strength
To help make sure that you place the unit in a suitable position you can text the unit to see
how much signal strength the Auto Dialler is receiving. Please text the command
#SIGNAL#
The Auto Dialler will perform a test on the signal strength and report with a score of
between 0 to 30. We strongly recommend that you place the unit where you will a signal
score of at least 10. You will find anything less that this will make the unit unreliable.
Dipswitch 1 - 2G or 3G
With dipswitch 1 set to on, the unit will boot up in 3G, with it set to off it will boot up in 2G.
To change the frequncy it looks for you will need to reset power when you change
dipswitch 1 for it to take effect.

Below is a notepad to help you remember the numbers that you have saved to your unit in
the event you need to modify or delete in the future.
#1=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#2= _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#3=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
Page 4
How to Programme Contact Numbers
After inserting your simcard into your Auto Dialler, turn the unit on and wait to see the
GREEN READY LED light come on. This will indicate that you have a mobile signal and
the unit is ready for use.
You will now need to send a text with the contact number.
NOTE - To avoid confusion we have colour coded the HASH (#) and the EQUALS (=)
symbols. The number should be your number or one you wish to be able to enable the
device. (Maximum of 3 contact numbers)
Example: (hash) (1,2 or 3) (equals) (phone number) (hash)
#1=07123456789# To save for contact no:1
#2=07234567891# To save for contact no:2
#3=07345678912# To save for contact no:3
If you wish to cancel a number, please follow this example
Example: (hash) (1,2 or 3) (equals) (DELETE) (hash)
#1=DELETE# Then send this to the simcard within the unit.
PLEASE NOTE
Please send one message at a time and wait for the Auto Dialler to send back the text
acknowledgement ‘NUMBER STORED’ before you attempt to send the next number.

You can now change the alarm message for inputs 1 & 2 to your own choosing.
To change the message send the text command as follows.
NOTE - Your message should read a message of your choosing up to 19 characters long.
# MESS1=YOUR MESSAGE# The default message is (Input 1)
#MESS2=YOUR MESSAGE# The default message is (Input 2)
This will change the message to ‘YOUR MESSAGE’
Page 5
How to Programme the SMS
Telephone Call Alerts
The Auto Dialler can be programmed to send you a call after each text alarm has been
sent.
You will receive approximately three ring tones. The unit will then hang up automatically
avoiding any call charges being incurred.
To set call alerts to ON please send the text message
#CALL=ON#
The unit will reply back ‘CALL ON’
To disarm the call alerts please send the text message.
#CALL=OFF#
If the call function has been set to ON you will receive a text message and shortly after a
phone call.

Page 6
How to Use the GSM Auto Dialler
The Auto Dialler has two inputs.
Input 1 = Terminal 1 Connection. (Negatively Triggered) Pulled to Ground
Input 2 = Terminal 2 Connection. (Negatively Triggered) Pulled to Ground
When the inputs are triggered the GREEN READY LED will flash six times to indicate that
a trigger has been received and it will send a text and/or call to the saved user numbers.
Both Input 1 and input 2 can be triggered independently.
The Auto Dialler will reset automatically when the triggered input is released.
NOTE: (Terminal 3) Input 2 Only
This can be triggered with a positive supply 12v/24v (refer to page 9)
How to Use the Relay Output
Dipswitch 2 = OFF (refer to page 3)
The Auto Dialler has an 8 amp volt free contact relay output that can be used to switch on
external electronic devices such as lighting, sirens etc.
By texting the unit you can turn the relay ON or OFF. Below are examples on how to do
this.
#REL=ON# This will turn the relay output ON
#REL=OFF# This will turn the relay output OFF
After each operation the unit will reply with a status report RELAY ON/OFF
It is possible to pulse the ouput relay for a period of 20 seconds. You will to send the text
as follows
#REL=PULSE# This will pulse the relay for 20 seconds.
Dipswitch 2=ON (refer to page 3)
The relay can also be setup to pulse for 20 seconds when inputs have been triggered. To
activte this mode you need to set DIPSWITCH 2 to the on position. (Refer to page 3).
This can be used to reset auxiliary equipment.
When the relay has been activated, the red relay led will light to indicated the relay is in
operation.

Page 7
Dipswitch settings
Dipswitch 1 = ON = 3G Selected
OFF = 2G Selected
Dipswitch 2 = ON= Relay Mode on
OFF= Relay Mode off
Reset
To reset the unit back to factory settings you will need to send a text message
#RESET#
WARNING This will reset all of your parameters. Only send a reset command when
necessary.
The GREEN READY LED will flash 8 times.
Note - Dipswitch 1 not used on 2G only
Model
Quick Reference
Wireless Model please refer to page 8
Typical Application of this Product
●Pumping stations; tanks, oil or water levels
●Security alarm system applications
●Supervision and monitoring alarm systems
●Automatic monitoring system
●Vending machines security protection
●Buildings and real estate
●Weather Stations
●River monitoring and flood control
●Fridges/Fish Tanks
●Farming equipment and security

Model AD-SD-W WIRELESS has an RF module which allows connection to various
wireless sensors that will then trigger the dialler in the same way as hard wiring into input 1
and input 2.
Figure 1
Wireless Functions - Model AD-SD-W (wireless)
Pairing Wireless Sensors or Door Switch
To connect wireless sensors you will need to match the devices to the receiver on the
dialler. Typical process below however it can vary depending on the sensor.
1. Switch on the Auto Dialler.
2. Switch on the sensor and allow it to warm up for 15 seconds
3. Hold down the pairing button on the RF Module for 3 seconds (refer to figure 1)
4. Trigger the sensor
5. The RF module has a RED LED which will flash when pairing is complete.
How to Programme the Alarm
Once the sensors are paired, you can send the text command to activate the alarm.
#ALARM=ON# This will activate the alarm
#ALARM=OFF# This will deactivate the alarm
When sensor/door detect movement you will receive the text message
‘ALARM TRIGGERED’
NOTE - The alarm will need to be reactivated again once it has been triggered.
The alarm message can NOT be changed from ALARM TRIGGERED
Ensure you have set up your contact numbers as per instructions on page 4
Page 8

PAGE 9
For more technical support please browse the FAQ’s on our website
Alternatively email our technical support team at and we
will do our best to reply within 24 hours Monday - Friday.
06/08/19 AD
NOTE - Please ensure you supply a 9 - 24 volts DC from the battery terminals via a 2
amp fuse (for alarm panel instructions)
INPUT 1+2
As you can see in the circuit diagram above, the input can be activated by pulling the input
1 & 2 to ground. Alternatively, input 2 only can be positively triggered by using terminal 3.
RELAY OUTPUT volt free contact
The relay has Common, Normally Open and Normally Closed contacts which are capable
of 8 amp loads. This is suitable for turning ON or OFF electrical equipment. Alternatively it
can be used for resetting your alarm system.
The relay can be manually activated by text message commands or it can be set to pulse
for 20 seconds when an input has been activated - refer to page 6