GSM Activate Alarm Pro 20 User manual

Page 1
2G GSM ALARM PRO
20 ZONES
www.gsm-activate.co.uk
MODEL ALARM PRO 20

Page 2
Product Information
Our 4G GSM Alarm Pro is a standalone alarm system suitable for both indoor and outside usage and can
cover a large range from the base station to the sensors. It will alert you using GSM technology by sending
a text message and/or a phone call to your mobile phone or land line when the sensors are broken, alerting
you to a possible intrusion or fault.
The unit is enclosed in an IP65 rated enclosure, meaning it is perfectly weathered for outside installation
and has passed testing in high heats and below freezing conditions.
GSM Module Specification
● GSM Frequency: quadband Freq 2G 900/1800/1900 / (3G) 2100 / (4G) 2600 Mhz
● Power Supply Voltage: 9 - 24 volts DC - 2 Amp Min
● Current Used in Standby Mode: 50mA Max
● IP65 Rated Enclosure for Outside Installation
● Micro 2G or 3G Simcard
● No Land Line Required
● Dimensions - L100 x W68 x H50mm
● Dimensions PCB Only - L95 x W67mm
● Sim Active Function
● Operating Temperature: -10…+40°C
● Programmed by Text Message
● Text to Text Signal Strength
● Wireless Range - Beam 50m
- Key Fob 50m
- PIR 80m
● Battery Backup
● Disable Zone Remotely
Solar Beam Specification
● Alert Distance: 100 meters
● Detection: 2 beams blocked simultaneously
● Battery Life: Solar Powered Charged Lithium Battery 900mah - 3 months from full charge. Replace
battery every 2 years
● Dimensions - L60 x W32 x H13mm
Outdoor PIR Specification
● Detection Range: 12m*12m
● Pet Immunity - 20kg
● Battery Life: AA Lithium Battery - 6 Months
● Mount Height: 1.8m - 2.4m
● Dimensions - L 148 x W75 x H54mm

Page 3
Instructions
IMPORTANT - PLEASE READ
PLEASE ENSURE THAT YOU DISCONNECT THE POWER & TURN THE BATTERY
OFF WHEN YOU FIT THE SIMCARD THEN PLACE THE SIMCARD WITH THE
CLIPPED CORNER FACING UPWARDS.
PLEASE SEE PICTURE ABOVE
Signal Strength
To help ensure that you place the unit in a suitable position, you can text the unit to see
how much signal strength the detector is receiving by texting the command
#SIGNAL#
The alarm will perform a test on the signal strength.
You will receive a text confirming the signal strength between 0 up to 30. We strongly
recommend that you place the unit where it can receive a signal of at lease 10.
less than this will make the unit unreliable.
Battery Backup
In the event of a power failure the internal rechargable battery will be capable of running
the unit for 24 hours. It will inform you of a “MAINS FAILURE” by text message as well as
when the power is restored with the text message “POWER RESTORED”.
You can switch the battery on and off using the switch inside the unit. (See image above)

Page 4
How to Programme the Mobile Number
After inserting the simcard into the GSM module, turn the unit on and wait until you see
the GREEN LED come on. This indicates that the module has a signal and the unit is
ready to be used.
Please Note - To avoid confusion we have colour coded the hash (#) and the equals (=)
symbols. Furthermore, where it indicates a phone number this should be
your number or the numbers you wish the unit to contact.
To programme your phone numbers into the unit you will need to send the text message
as follows:
Example: (hash) (PH) (equals) (phone number) (hash)
#PH1=07123456789# Then send this to the unit simcard number.
#PH2=07753651298# Then send this to the unit simcard number.
The unit will reply number stored
When the unit is triggered it will send an alarm message to thiese numbers
How to programme the SMS Text Message
You can now change the alarm default message from “IR??” To one of your choice.
To change the message send the text command as follows
#IR01=YOUR MESSAGE# Default message is IR01
#IR02=YOUR MESSAGE# Default message is IR02
The detector will reply with the text message - “MESSAGE STORED”
By changing position 01 to 20, you can name all 20 individually paired sensors.
PLEASE NOTE
Your can only use a maximum of 30 characters including spaces for your customised
message.
How to Setup Call Alerts
The auto dialler can be programmed to send you a telephone call after each text alarm
has been sent.
You will receive approximately three ring tones. The unit will then hang up automatically.
This is to prevent call charges being incurred.
To set call alerts to ON please send the text message
#CALL=ON#
The unit will reply back “call on”
To disarm call alerts please send the text message.
#CALL=OFF#
You will then revert back to the default text message only alert

Page 5
The Sensors
The GSM Alarm Pro 20 has the ability to pair up to 20 sensors. These sensors can be programmed with
their own unique location code so the end user will know exactly which sensor has been triggered.
The sensors and key fobs are easily paired by using the colour touch screen display on the board.
Pairing the Sensors
1. Touch the screen
2. Press the RED “SENSOR OPTION”
3. Choose a location 1-20 to store the sensor using the + and - icons.
4. Touch the “SELECT LOCATION” - a prompt will appear saying “ACTIVATE SENSOR NOW”
5. Activate your sensor
6. Touch “SAVE-YES” - You will hear 3 beeps to confirm
NOTE - Once a sensor has been stored to a location, it cannot be stored to another location without it being
unpaired using a reset.
Pairing the Key Fobs
● Press the GREEN key option
● It will show 3 positions and have an X or - symbol - this shows whether a keyfob is paired to it
● Choose a location from 1-3
● You will then get a prompt to “PRESS KEY FOB A”
● Press the “A” ONLY on your key fob
● This will be followed by a beep to signal it has been paired and stored to that location
Delete Sensors / key fob
To delete the sensors or key fobs, touch the YELLOW RESET command. It will ask you whether you want to
remove ALL sensors or ALL key fobs
SIM Active Function
Our GSM Auto Dialler comes with a SIM Active function meaning that it will send a
message every six weeks to a preprogrammed number we at GSM Activate own to prevent
the SIM card being shut down due to inactivity.

How to turn ON / OFF the Alarm
Once you have paired and positioned the sensors and key fobs the alarm is ready to be used.
Arm Using Text Message
To set the alarm to ON you will need to send the text message
#ALARM=ON# This will activate the alarm
#ALARM=OFF# This will deactivate the alarm
Arm Using the Key Fob
The key fob works best when used with the siren provided as this provides an audible alert whenever you
arm or disarm the alarm.
Press Button A on the Key Fob This ARMS the alarm.
The siren will beep TWICE
Press Button B on the Key Fob This DISARMS the alarm
The siren will beep ONCE
Once the Alarm has been alarmed, it will stay alarmed even after an alarm activation, To turn off the
alarm and stop further alarm messages you will have to disarm the alarm by text or key fob
How to Use The Siren Output
The unit has been programmed to trigger the siren for 60 seconds in the event of an alarm activation. Once
the text message has been received you can STOP the siren sounding by pressing B on the key fob.
The length of time the siren sounds for can be altered from 10 to 90 seconds by sending the text command
#SIREN=0# Turns siren OFF
#SIREN=1# Sets siren to sound for 10 seconds upon activation.
#SIREN=6# Sets siren to sound for 60 seconds upon activation (default setting)
#SIREN=9# Sets siren to sound for 90 seconds upon activation
Page 6
Activating the Alarm
Once the alarm is armed via text or keyfob, the alarm is then ready and sensing all paired beams.
When a sensor is broken this will trigger the siren for the pre determined length of time and also send a
text message to two pre programmed phone numbers, it will also call if you have set the call on feature
(see page 4)
The text message will relate to which sensor has been broken - you can pair upto 20 sensors and name
them individually to individually name see page 5 . The default texts are IR01, IR02 etc
Once the alarm has been activated , it will automatically re-arm once the beam has been cleared.
Disabling Sensor 1 Only
If you want to remove sensor 1 from operation you send the text command
#BEAM1=ON# This will re-enable sensor 1
#BEAM1=OFF# This will disable sensor 1
The purpose of this function is to deactivate one sensor whilst retaining the rest of the alarm system, this
could be for a constantly used door during day time hours.

For more technical support please browse the FAQ’s on our website www.gsm-
activate.co.uk
Alternatively email our technical support team at [email protected] and we
will do our best to respond to your querry within 24 hours Monday- Friday.
Quick Reference
Factory Reset
To reset the unit back to factory settings you will need to send the text message
#RESET#
PLEASE NOTE - By doing this you will reset ALL of your parameters. ONLY send this seset command
when necessary.
The GREEN ready LED will flash eight times.
20/07/21 - GD Page 7