GUBI BEETLE DINING CHAIR User manual

ASSEMBLY INSTRUCTIONS
for
BEETLE DINING CHAIR
CARE INSTRUCTIONS
Daily cleaning can be done by wiping the base
and plastic shell with a clean dry cloth. Should the
surface need more attention this can be cleaned
with water and a light detergent or soap applied
with a damp cloth. Wipe after with a clean dry
cloth. Avoid any abrasive materials.
04-20-003-01 Assembly instructions Beetle Dining Chair.
For enquiries contact GUBI A/S - CVR: 17940384
Klubiensvej 7-9. 2150 Nordhavn. Copenhagen, Denmark
T [phone] – [email protected]
GUBI.COM

ASSEMBLY INSTRUCTIONS
BEETLE DINING CHAIRCONTENTS.
x1x4 x4 x16
1.
3. 4.
2.
Frihavnen Klubiensvej 7-9
Pakhus 53
DK 2150 Copenhagen
Phone: [phone]
Fax: [phone]
www.gubi.com
4pcs /chair
1pcs/chair
Can you remove
the line on the leg?
Can you remove the line on the leg?
Umbraco key
1pcs/chair
Turn the chair upside down
Finished chair
Place the shell upside down on a table
Cover the surface with a blanket or similar, to avoid scratches on the plastic shell
Beetle asmb instruction
DWG NO.:
MATERIAL:
INITIALS:
PAPER SIZE:
DESCRIPTION:
PROPERTY AND CONFIDENTIAL INFORMATION: This design may not be distributed or reproduced without the written permission of GUBI A/S
SHEET 1 OF 2
A3
IF NOTHING ELSE SPECIFIED MEASUREMENTS IN MM
APPROVED BY: DATE:
DS/ISO 2768-1 m
GENERAL TOLERANCES:
1:10
SCALE:
M6x12 black Steel~010.9 // ISO 7380-2
REVISION DATE:
REVISION: WEIGHT [g]
0.52
PRODUCT:
Frihavnen Klubiensvej 7-9
Pakhus 53
DK 2150 Copenhagen
Phone: [phone]
Fax: [phone]
www.gubi.com
4pcs /chair
1pcs/chair
Can you remove
the line on the leg?
Can you remove the line on the leg?
Umbraco key
1pcs/chair
Turn the chair upside down
Finished chair
Place the shell upside down on a table
Cover the surface with a blanket or similar, to avoid scratches on the plastic shell
Beetle asmb instruction
DWG NO.:
MATERIAL:
INITIALS:
PAPER SIZE:
DESCRIPTION:
PROPERTY AND CONFIDENTIAL INFORMATION: This design may not be distributed or reproduced without the written permission of GUBI A/S
SHEET 1 OF 2
A3
IF NOTHING ELSE SPECIFIED MEASUREMENTS IN MM
APPROVED BY: DATE:
DS/ISO 2768-1 m
GENERAL TOLERANCES:
1:10
SCALE:
M6x12 black Steel~010.9 // ISO 7380-2
REVISION DATE:
REVISION: WEIGHT [g]
0.52
PRODUCT:
Frihavnen Klubiensvej 7-9
Pakhus 53
DK 2150 Copenhagen
Phone: [phone]
Fax: [phone]
www.gubi.com
4pcs /chair
1pcs/chair
Can you remove
the line on the leg?
Can you remove the line on the leg?
Umbraco key
1pcs/chair
Turn the chair upside down
Finished chair
Place the shell upside down on a table
Cover the surface with a blanket or similar, to avoid scratches on the plastic shell
Beetle asmb instruction
DWG NO.:
MATERIAL:
INITIALS:
PAPER SIZE:
DESCRIPTION:
PROPERTY AND CONFIDENTIAL INFORMATION: This design may not be distributed or reproduced without the written permission of GUBI A/S
SHEET 1 OF 2
A3
IF NOTHING ELSE SPECIFIED MEASUREMENTS IN MM
APPROVED BY: DATE:
DS/ISO 2768-1 m
GENERAL TOLERANCES:
1:10
SCALE:
M6x12 black Steel~010.9 // ISO 7380-2
REVISION DATE:
REVISION: WEIGHT [g]
0.52
PRODUCT:
Frihavnen Klubiensvej 7-9
Pakhus 53
DK 2150 Copenhagen
Phone: [phone]
Fax: [phone]
www.gubi.com
4pcs /chair
1pcs/chair
Can you remove
the line on the leg?
Can you remove the line on the leg?
Umbraco key
1pcs/chair
Turn the chair upside down
Finished chair
Place the shell upside down on a table
Cover the surface with a blanket or similar, to avoid scratches on the plastic shell
Beetle asmb instruction
DWG NO.:
MATERIAL:
INITIALS:
PAPER SIZE:
DESCRIPTION:
PROPERTY AND CONFIDENTIAL INFORMATION: This design may not be distributed or reproduced without the written permission of GUBI A/S
SHEET 1 OF 2
A3
IF NOTHING ELSE SPECIFIED MEASUREMENTS IN MM
APPROVED BY:
DATE:
DS/ISO 2768-1 m
GENERAL TOLERANCES:
1:10
SCALE:
M6x12 black Steel~010.9 // ISO 7380-2
REVISION DATE:
REVISION:
WEIGHT [g]
0.52
PRODUCT:
Frihavnen Klubiensvej 7-9
Pakhus 53
DK 2150 Copenhagen
Phone: [phone]
Fax: [phone]
www.gubi.com
4pcs /chair
1pcs/chair
Can you remove
the line on the leg?
Can you remove the line on the leg?
Umbraco key
1pcs/chair
Turn the chair upside down
Finished chair
Place the shell upside down on a table
Cover the surface with a blanket or similar, to avoid scratches on the plastic shell
Beetle asmb instruction
DWG NO.:
MATERIAL:
INITIALS:
PAPER SIZE:
DESCRIPTION:
PROPERTY AND CONFIDENTIAL INFORMATION: This design may not be distributed or reproduced without the written permission of GUBI A/S
SHEET 1 OF 2
A3
IF NOTHING ELSE SPECIFIED MEASUREMENTS IN MM
APPROVED BY: DATE:
DS/ISO 2768-1 m
GENERAL TOLERANCES:
1:10
SCALE:
M6x12 black Steel~010.9 // ISO 7380-2
REVISION DATE:
REVISION: WEIGHT [g]
0.52
PRODUCT:
Cover a surface with a blanket or similar, to avoid scratches on the plastic shell.
Place the shell upside down on the surface and hold steadily as it may fall.
Place the screws through the holes in the base
and into the threaded holes in the shell.
Finished chair.
Tighten the screws, until firmly mounted. Do not
over tighten as this may damage the shell.
Place the base on top of the shell and make sure the holes
are aligned. If the holes do not align, turn the base around.
Place the screws in the the holes in the frame
and the threaded holes in the frame
Tighten the screws, until the screw
is firmly mounted
Do not use too much force
Place the frame on top
of the shell and make sure the
holes are aligned.
If the holes do not fit, turn the frames around
Arrow to show
how to fasten the screw.
Place the screws in the the holes in the frame
and the threaded holes in the frame
Tighten the screws, until the screw
is firmly mounted
Do not use too much force
Place the frame on top
of the shell and make sure the
holes are aligned.
If the holes do not fit, turn the frames around
Arrow to show
how to fasten the screw.
Place the screws in the the holes in the frame
and the threaded holes in the frame
Tighten the screws, until the screw
is firmly mounted
Do not use too much force
Place the frame on top
of the shell and make sure the
holes are aligned.
If the holes do not fit, turn the frames around
Arrow to show
how to fasten the screw.