Hama EWS-Trio User manual

Weather Station EWS-Trio
Wetterstation
E
F
D
GB
Operating Instructions
Bedienungsanleitung
Mode d‘emploi
Instrucciones de uso
Руководство по эксплуатации
Istruzioni per l‘uso
Instrukcja obsługi
Návod kpoužití
Návod na použitie
Manual de utilizare
RUS
I
PL
CZ
SK
RO
00
136293

A B
1
17
18
5
19
6 7
3
20
21
42
14 15
11109 138 12
16

2
GOperating instruction
Controls and Displays
ABase station
1. Time
2. Room temperature
3. Day of the week +date +calendar month DCF
signal radio symbol
4. Room humidity
5. Outdoor temperature/outdoor humidity channel 1
(CH1), low battery level display for measuring
station 1
6. Outdoor temperature/outdoor humidity channel 2
(CH2), low battery level display for measuring
station 2
7. Outdoor temperature/outdoor humidity channel 3
(CH3), low battery level display for measuring
station 3
8. ALARM button =displaying/setting/deactivating/
activating the alarm functions
9. CH button =manual search for asignal from the
measuring station/channel selection
10. SNZ/LIGHT button =temporarily interrupts the
alarm (snooze)/activates the backlight
11. SET button =settings/conrms the setting
12. UP button =increases the current set value/recalls
the saved maximum/minimum values (MAX/MIN)
13. Down button =decreases the current set value/
toggles between °C and °F /activates/deactivates
manual DCF radio signal reception
14. +16. Fold-out bases
15. Battery compartment
BMeasuring station
17. Transmission indicator light
18. TX button =manual connection to the base
station
19. Recess for wall mounting
20. Slide switch =selects channel 1, 2or3
21. Battery compartment
Thank you for choosing aHama product.
Take your time and read the following instructions and
information completely.Please keep these instructions in a
safe place for futurereference. If you sell the device, please
pass these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to
draw your attention to specic hazards and risks.
Note
This symbol is used to indicate additional information or
important notes.
2. Package Contents
•Trio weather station (base station for indoors)
•3measuring stations for outdoors
•3AAA batteries
•6AAbatteries
•These operating instructions
3. Safety Notes
•The product is intended for private, non-commercial use
only.
•Do not operate the product outside the power limits given
in the specications.
•Do not use the product in moist environments and avoid
splashes.
•Do not use the product in the immediate vicinity of heaters
or other heat sources or in direct sunlight.
•Do not use the product in areas wherethe use of electronic
devices is not permitted.
•Do not place the product near interference elds, metal
frames, computers, TVs, etc. Electronic devices and window
frames can negatively affect the product’sfunctionality.
•Do not drop the product and do not expose it to any major
shocks.

3
•Do not open the device or continue to operate it if it
becomes damaged.
•Do not attempt to service or repair the product yourself.
Leave any and all service work to qualied experts.
•Keep the packaging material out of the reach of children
due to the risk of suffocation.
•Dispose of packaging material immediately according to
locally applicable regulations.
•Do not modify the product in any way.Doing so voids the
warranty.
Warning –Batteries
•Immediately remove and dispose of dead batteries from
the product.
•Only use batteries (or rechargeable batteries) that
match the specied type.
•Do not mix old and new batteries or batteries of a
different type or make.
•When inserting batteries, note the correct polarity (+
and -markings) and insert the batteries accordingly.
Failuretodosocould result in the batteries leaking or
exploding.
•Do not charge batteries.
•Keep batteries out of the reach of children.
•Do not short circuit the batteries/rechargeable batteries
and keep them away from uncoated metal objects.
4. Getting started
Note
Beforeuse, make surethat you insert the batteries in the
measuring station rst and then in the base station.
4.1 Measuring station
•Open the batterycompartment (21) and insert two
AA batteries with the correct polarity into the battery
compartment.
•Use the slideswitch (20) to select the channel that the
respective measuring station is to use for transmission.
Each of the three measuring stations must use adifferent
channel!
•Close the battery compartment.
4.2 Base station
•Open the batterycompartment (15) and insert three
AAA batteries with the correct polarity into the battery
compartment.
•Then close the battery compartment cover.
4.3 Replacing the batteries
Note –Replacing the batteries
•Note that the stations have to be resynchronised each
time after you change the batteries in the measuring
or base station.
•To do this, remove the batteries from the other station
and then reinsert them, or change them as required.
Measuring station
•If the symbol is displayed on the basis station in the
measurement values area of one of the three measuring
stations (5/6/7), replace the two AA batteries of the
affected measuring station with two new ones.
•Open the battery compartment (21), remove and properly
dispose of the depleted batteries, and insert two new AAA
batteries with the correct polarity.Then close the battery
compartment cover.
Base station
•If the symbol is displayed on the base station in the
indoor values area (2), replace the three AAA batteries in
the base station with three new ones.
•Open the battery compartment (15), remove and properly
dispose of the dead batteries and insert three new AAA
batteries with the correct polarity.Then close the battery
compartment cover.

4
5. Installation
Note –Installation
•We recommend initially placing the base station and
measuring station(s) in the intended locations without
installing them and making all the settings described in
6. Operation.
•Only install the stations once the appropriate settings
have been made and astable wireless connection is
established.
Note
•The wireless transmission range between the measuring
and base stations is up to 50 minopen spaces.
•Beforeinstallation, ensurethat wireless transmission
will not be disrupted by interference or obstacles like
buildings, trees, vehicles, high-voltage lines, etc.
•Beforethe nal installation, ensurethat thereis
sucient reception between the intended installation
locations.
•When installing the measuring station, ensurethat it is
protected from direct sunlight and rain.
•The international standardheight for measuring air
temperatureis1.25 m(4ft) above ground.
Warning
•Buy special or suitable installation material from a
specialised dealer for wall-mounting.
•Ensurethat no faulty or damaged parts areinstalled.
•Never apply force during installation. This could
damage the product.
•Beforeinstallation, ensurethat the chosen wall is
suitable for the weight to be mounted, and make sure
that thereare no electrical wires, water,gas or other
lines at the installation site on the wall.
5.1 Base station
•Use the base to position the base station on alevel
surface.
5.2 Measuring station
•Youcan also position the measuring station on alevel
outdoor surface.
•We recommend installing the measuring station securely
on an outdoor wall using the opening (19).
6. Operation
6.1 Connection to the measuring station
After you have inserted the batteries, the base station
automatically searches for aconnection to the three
measuring stations and performs initial setup.
Note
•Remember that each of the three measuring stations
must use adifferent channel.
•Initial setup takes approximately 3minutes.
•During the connection attempt, the measuring station
radio symbol will ash.
•Do not press any buttons during setup. Otherwise,
values may not be transmitted correctly and thereisa
risk of value errors and inaccuracies.
•The process is completed when the indoor (2/4) and
outdoor (5/6/7) measurement data is displayed.
•If asignal from the measuring station is still not received,
select one of the three channels by pressing the CH button
(9). Then hold the CH button (9) for approximately 3
seconds to start the manual search for the signal.
•Press the TX button (18) on the desired measuring station
to initiate the transmission of asignal that can be received
by the base station.

5
6.2 Basic and manual settings
Automatic setting using the DCF signal (radio-
controlled clock)
•When the base station has been switched on for the rst
time and successful transmission has been established
between the base station and the measuring station, the
clock will automatically search for the DCF signal. During
the search, the radio symbol for DCF reception ashes.
Display (8) Searching for the DCF signal
Display ashing
Active
Displayed continuously
Successful –signal is being received
Not displayed Deactivated
•If the station still does not receive asignal, press and hold
the DOWN button (13) until the radio symbol begins to
ash, to start the manual search for the DCF signal.
Note –Time settings
•The search process takes about 3minutes. If the search
fails, it ends and is repeated at the next clock hour.The
radio symbol ( )goes out.
•It is not possible to manually set the time and date
during the search for the DCF signal.
•The clock automatically continues to search for the DCF
signal on adaily basis (between 1amand 5am) to
correct any deviations.
•If the signal is received successfully,the manually set
time and date areoverwritten.
•Press and hold the DOWN button (13) again for
approximately 3seconds to stop the manual search.
Note –Summer time
•The clock automatically switches to summer time.
Manual settings
Note
•Hold the UP button (12) or the DOWN button (13) to
select the values faster.
•Press the SET button (11) to make the following settings
in order:
•Time zone
•Year
•Calendar month
•Date
•Hour
•Minute
•12/24-hour format
•To select individual values, press the UP button (12) or the
DOWN button (13) and conrm each selection by pressing
the SET button (11).
•Press the SET button (11) to adopt the set value displayed
and to skip.
•If you do not make an entry for 20 seconds, you
automatically exit the setting mode.
Note –Time zone
•The DCF signal can be received over long distances, but
always transmits the current Central European Time in
Germany.Please note that for countries with adifferent
time zone, you must set the time difference manually.
•If you areinMoscow,for example, the time is 3hours
later than in Germany.This means that you should
set +3 for the time zone. The clock then sets the time
automatically to 3hours ahead after receiving the DCF
signal or according to the manually set time.

6
Celsius /Fahrenheit
•Press the DOWN button (13) to switch between °C and °F
for the temperaturedisplay.
6.3 Alarm
Alarm mode AL is displayed between the hours and minutes
of the time display.
•Press the ALARM button (8) once to call up alarm mode.
•Press and hold the ALARM button (8) for approximately
3seconds to set the alarm time. The hours display begins
to ash.
•Press the UP button (12) or the DOWN button (13)
to select the hour for the alarm time and conrm your
selection by pressing the ALARM button (8). The minutes
display begins to ash.
•Repeat the process to set the minutes for the alarm time.
•If you do not make an entry for approximately 5seconds,
you automatically exit the setting mode.
•Press the DOWN button (13) to activate or deactivate
the alarm. An active alarm is displayed by the alarm
symbol ( ). The alarm symbol goes out when the alarm
is deactivated.
•If the alarm is triggered, the alarm symbol ( )will begin
to ash and an alarm will sound.
•Press any button (except the SNZ/LIGHT button (10)) to
stop the alarm. Otherwise, it will stop automatically after
2minutes.
Note –Snooze function
•While the alarm signal is sounding, press the SNZ/
LIGHT button (10) to activate the snooze function. The
alarm symbol ( )will start to ash on the display.The
alarm signal will stop for 5minutes, after which it will
sound again.
•Press any button (except the SNZ/LIGHT button) to
stop the snooze function and the alarm.
6.4 Maximum and minimum temperature and
humidity values
The base station automatically stores the maximum and
minimum outdoor/indoor temperatureand humidity values.
•Repeatedly press the UP button (12) to switch the
display between the current temperatureand humidity,
maximum temperatureand humidity (MAX) and minimum
temperatureand humidity (MIN).
6.5 Backlight
•Press the SNZ/LIGHT button (10) to light up the display
for approximately 5seconds.
7. Care and Maintenance
•Only clean this product with aslightly damp, lint-free cloth
and do not use aggressive cleaning agents.
•Make surethat water does not get into the product.
8. Warranty Disclaimer
Hama GmbH &CoKGassumes no liability and provides no
warranty for damage resulting from improper installation/
mounting, improper use of the product or from failureto
observe the operating instructions and/or safety notes.
9. Service and Support
Please contact Hama Product Consulting if you have any
questions about this product.
Hotline: [phone] (German/English)
Further support information can be found here:
www.hama.com

7
10. Technical Data
Base station Measuring station
Power supply
4.5 V
3x AAA batteries 3.0 V 2xAAbatteries
We recommend using AA lithium batteries for
the outdoor sensors when outdoor
temperatures arebelow 0°C/32°F.
Measuring range:
Temperature
Humidity 0°C –+50°C /32°F –+122°F 10 –99% -40°C –+70°C /-40°F –+158°F 20% –95%
Measurement increments:
Temperature
Humidity 0.1°C/ 0.2°F 1% 0.1°C/ 0.2°F 1%
Radio-controlled DCF clock YesNo
Thermometer YesYes
Hygrometer YesYes
Alarm function YesNo
Max. number of measuring stations 3
Range ≤30m
11. Recycling Information
Note on environmental protection:
After the implementation of the European Directive
2012/19/EU and 2006/66/EU in the national legal
system, the following applies: Electric and electronic
devices as well as batteries must not be disposed of
with household waste. Consumers areobliged by law to
return electrical and electronic devices as well as batteries at the
end of their service lives to the public collecting points set up for
this purpose or point of sale. Details to this aredened by the
national law of the respective country.This symbol on the product,
the instruction manual or the package indicates that aproduct is
subject to these regulations. By recycling, reusing the materials or
other forms of utilising old devices/batteries, you aremaking an
important contribution to protecting our environment.
12. Declaration of Conformity
Hereby,Hama GmbH &CoKGdeclares that the
radio equipment type [00136293] is in compliance
with Directive 2014/53/EU.The full text of the EU
declaration of conformity is available at the following internet
address: www.hama.com ->00136293 -> Downloads.
Frequency band(s) 433 MHz
Maximum radio-frequency power
transmitted
9,419 mW

8
DBedienungsanleitung
Bedienungselemente und Anzeigen
ABasisstation
1. Uhrzeit
2. Raumtemperatur
3. Wochentag +Datum +Kalendermonat
Funksymbol DCF Signal
4. Raumluftfeuchtigkeit
5. Außentemperatur/Außenluftfeuchtigkeit Kanal 1
(CH1), Anzeige für niedrigen Batteriestand
Messstation 1
6. Außentemperatur/Außenluftfeuchtigkeit Kanal 2
(CH2), Anzeige für niedrigen Batteriestand
Messstation 2
7. Außentemperatur/Außenluftfeuchtigkeit Kanal 3
(CH3), Anzeige für niedrigen Batteriestand
Messstation 3
8. ALARM-Taste =Anzeige/ Einstellung/
Deaktivierung/ Aktivierung der Alarmfunktionen
9. CH-Taste =Manuelle Suche nach Signal der
Messstation/Kanalauswahl
10. SNZ/LIGHT-Taste =(Snooze) Unterbrechung des
Wecksignals /Aktivierung Hintergrundbeleuchtung
11. SET-Taste =Einstellungen /Bestätigung des
Einstellungswerts
12. UP-Taste =Erhöhung des aktuellen
Einstellungswertes/ Abruf der gespeicherten
Höchst-/ Tiefstwerte (MAX/MIN)
13. Down-Taste= Verringerung des aktuellen
Einstellungswertes /Wechsel zwischen °C und
°F /Aktivierung/ Deaktivierung manueller DCF
Funksignal Empfang
14. +16. AusklappbareStandfüße
15. Batteriefach
BMessstation
17. Kontrollleuchte Übertragung
18. TX-Taste =Manuelle Verbindung mit der
Basisstation
19. Aussparung für Wandmontage
20. Schiebeschalter =Kanalauswahl 1,2 oder 3
21. Batteriefach
Vielen Dank, dass Sie sich für ein Hama Produkt entschieden
haben! Nehmen Sie sich Zeit und lesen Sie die folgenden
Anweisungen und Hinweise zunächst ganz durch. Bewahren
Sie diese Bedienungsanleitung anschließend an einem
sicheren Ort auf,umbei Bedarf darin nachschlagen zu
können. Sollten Sie das Gerät veräußern, geben Sie diese
Bedienungsanleitung an den neuen Eigentümer weiter.
1. Erklärung von Warnsymbolen und Hinweisen
Warnung
Wirdverwendet, um Sicherheitshinweise zu kennzeichnen
oder um Aufmerksamkeit auf besondereGefahren und
Risiken zu lenken.
Hinweis
Wirdverwendet, um zusätzlich Informationen oder
wichtige Hinweise zu kennzeichnen.
2. Packungsinhalt
•Wetterstation Trio (Basisstation für den Innenraum)
•3Messstationen für den Außenbereich
•3AAA-Batterien
•6AA-Batterien
•diese Bedienungsanleitung
3. Sicherheitshinweise
•Das Produkt ist für den privaten, nicht-gewerblichen
Haushaltsgebrauch vorgesehen.
•Betreiben Sie das Produkt nicht außerhalb seiner in den
technischen Daten angegebenen Leistungsgrenzen.
•Verwenden Sie das Produkt nicht in einer feuchten
Umgebung und vermeiden Sie Spritzwasser.
•Betreiben Sie das Produkt nicht in unmittelbarer Nähe
der Heizung, anderer Hitzequellen oder in direkter
Sonneneinstrahlung.
•Benutzen Sie das Produkt nicht in Bereichen, in denen
elektronische Produkte nicht erlaubt sind.

9
•Positionieren Sie das Produkt nicht in der Nähe von
Störfeldern, Metallrahmen, Computern und Fernsehern etc.
Elektronische Geräte sowie Fensterrahmen beeinträchtigen
die Funktion des Produktes negativ.
•Lassen Sie das Produkt nicht fallen und setzen Sie es
keinen heftigen Erschütterungen aus.
•Öffnen Sie das Produkt nicht und betreiben Sie es bei
Beschädigungen nicht weiter.
•Versuchen Sie nicht, das Produkt selbst zu warten oder zu
reparieren. Überlassen Sie jegliche Wartungsarbeit dem
zuständigen Fachpersonal.
•Halten Sie Kinder unbedingt von dem Verpackungsmaterial
fern, es besteht Erstickungsgefahr.
•Entsorgen Sie das Verpackungsmaterial sofort gemäß den
örtlich gültigen Entsorgungsvorschriften.
•Nehmen Sie keine Veränderungen am Produkt vor.
Dadurch verlieren Sie jegliche Gewährleistungsansprüche.
Warnung -Batterien
•Entfernen und entsorgen Sie verbrauchte Batterien
unverzüglich aus dem Produkt.
•Verwenden Sie ausschließlich Akkus (oder Batterien),
die dem angegebenen Typentsprechen.
•Mischen Sie alte und neue Batterien nicht, sowie
Batterien unterschiedlichen Typs oder Herstellers.
•Beachten Sie unbedingt die korrekte Polarität
(Beschriftung +und -) der Batterien und legen Sie
diese entsprechend ein. Bei Nichtbeachtung besteht
die Gefahr des Auslaufens oder einer Explosion der
Batterien.
•Laden Sie Batterien nicht.
•Bewahren Sie Batterien außerhalb der Reichweite von
Kindern auf.
•Schließen Sie Akkus/Batterien nicht kurz und halten Sie
sie von blanken Metallgegenständen fern.
4.
Inbetriebnahme
Hinweis
Beachten Sie, dass Sie bei der Inbetriebnahme immer
zuerst die Batterien in die Messstation, und dann in die
Basisstation einlegen.
4.1 Messstation
•Öffnen Sie das Batteriefach (21) und legen Sie 2AA
Batterien polrichtig ein.
•Wählen Sie mit dem Schiebeschalter (20) den Kanal
aus, auf dem die jeweilige Messstation senden soll. Jede
der 3Messstationen muss einen anderen Kanal nutzen!
•Schließen Sie die Batteriefachabdeckung anschließend.
4.2 Basisstation
•Öffnen Sie das Batteriefach (15) und legen Sie 3AAA
Batterien polrichtig ein.
•Schließen Sie die Batteriefachabdeckung anschließend.
4.3 Batterien wechseln
Hinweis –Batteriewechsel
•Beachten Sie, dass nach jedem Batteriewechsel an
Mess- oder Basisstation eine neue Synchronisation
erfolgen muss.
•Nehmen Sie dazu die Batterien der anderen Station
heraus und setzen sie erneut ein oder wechseln Sie
diese bei Bedarf ebenfalls aus.
Messstation
•Wenn das Symbol auf der Basisstation im Bereich der
Messwerte einer der drei Messstationen (5/6/7) angezeigt
wird, ersetzen Sie die 2AA-Batterien der betroffenen
Messstation durch 2entsprechende neue Batterien.
•Öffnen Sie das Batteriefach (21), entnehmen und
entsorgen Sie die verbrauchten Batterien und legen Sie
2neue AAA-Batterien polrichtig ein. Schließen Sie die
Batteriefachabdeckung anschließend.