HAMPTON BAY FSC18015-1 User manual

HAMPTONBAY.COM
10 FT. X 12 FT. SOLAR LED LIGHTED GAZEBO
USE AND CARE GUIDE
Item # 1004 815 945
Model #FSC18015-1

Table of Contents ...................................2
Safety Information ..................................2
Warranty ..........................................2
Maintenance ......................................3
Pre-Assembly ......................................4
Planning Assembly............................... . . 4
Hardware Included ........................... . .4
Package Contents ................................ . . 5
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Care and Cleaning .................................16
WARNING: READ ALL INSTRUCTIONS BEFORE USE.
Close supervision is necessary when this furnishing is used
by or near children, or disabled persons, if applicable.
Use this furnishing only for its intended use as described in
these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Do not leave the gazebo where there is a risk
of high wind, as possible damage will occur to the structure.
WARNING: This unit is heavy! Do not assemble this item
alone.
WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY
CAUTION: Do not climb on top of the gazebo. Falling off
the gazebo can result in serious injury, possibly even death.
www.HAMPTONBAY.com.
GAZEBO gazebo
flammability requirements of CPAI-84. The fabric may burn
if left in continuous contact with any flame source. The
application of any foreign substance to the gazebo fabric
may render the flame-resistant properties ineffective.
This assembly requires at least four people.
The warranty does not cover normal wear and tear, abuse or misuse of this product including damage from inclement weather
such as wind, rain, or hail. In case of inclement weather, remove all valuables and persons and seek appropriate shelter.
Remove the canopy from gazebo when there is high wind, snow,
storm, or any inclement weather to avoid any damage.
Put the gazebo on the level ground, and use ground stakes
and rope to better fasten it.
A failure to assemble this gazebo correctly could cause damage
or result in serious injury.

Maintenance
REPLACING THE BATTERY
NOTE: Use one Li-ion 18650 Lithium battery, 2000mAh,
3.7V rechargeable battery pack. For best performance,
replace with a Lithium rechargeable battery pack after 470
uses; normally every year, based on individual usage.
NOTE: To reduce the risk of damage to the electrical
connections, exercise caution when separating the battery
compartment base and cover.
IMPORTANT: When storing this gazebo, remove the
plate from the top, and store it on a cool and high place, to
increase service life.
IMPORTANT: Dispose of the battery in accordance with
local, state and federal regulations.
Loosen the two lock screws on the base and remove the cover
from the base.
Remove the old battery pack from the compartment and replace
with a new 18650 Lithium battery, 2000mAh, 3.7V rechargeable
battery pack.
Lock the base and cover with two screws.
During first use, the light might not work. Please leave the gazebo
under the sun to charge the solar plate.
Leave the gazebo in a sunny place to extend lighting duration.
screw
Lithium battery
Li-ion 18650
2000mAh 3.7V
battery compartment cover
battery compartment base
HAMPTONBAY.COM

Safety Goggles Safety Hat Level Gloves Step Ladder Phillips Screwdriver
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part
Description
Quantity
AA
32
BB
8
CC
24
DD
12
EE
1
AA
M6x15 bolt
Nut
Washer
Ground stake
Hex wrench
FF
1
Wrench
BB CC DD EE FF

4
4
4
4
4
Post
Long support bar
Short support bar
Long top bar
Corner bar
2
2
Short top bar
Middle top bar
1Top center connector
HAMPTONBAY.COM

1
1
4
4
1
1
4
4
Small canopy
Large canopy
Sidewall
Net sidewall
Solar plate
Light
Rope
Fixed component
K
L
M
N
O
P

Assembling the long support bars
AA
CC
AA
BB
P
B
B
AA
CC
AA
BB
P
C
C
Connect the two long support bars (B) using M6x15 bolts (AA), nuts (BB), washers (CC) and xed components (P).
Connect the two short support bars (C) using M6x15 bolts (AA), nuts (BB), washers (CC) and xed components (P).
Assembling the short support bars
HAMPTONBAY.COM

Attaching the long support bars to the posts
A
BB
AA
CC
A
C
C
C
C
AA
A
CC
Connect the long support bars (B) to the posts (A) using M6x15 bolts (AA) and washers (CC) at each corner.
Attaching the short support bars to the posts
Connect the long support bars (C) to the posts (A) using M6x15 bolts (AA) and washers (CC) at each corner.

E
DH
Assembling the top connector bar
Insert the wire connector on the long top bar (D) into the connector on the top center connector (H).
Insert the long top bar (D) into the top center connector (H) until the marble pops up.
Slide a short corner bar (E) onto the end of the long top bar (D) until the short corner bar (E) clicks into place.
HAMPTONBAY.COM

E
D
Link the corner bar (E) with the top center connector (H) onto the post (A).
Insert the other long top bars (D) with the short corner bars (E) into the top center connector (H) as Step 5.
Link the corner bars (E) onto the posts (A).
Attaching the top corner bars to the posts
NOTE: Suggested to stand on a ladder when assembling,
as shown below.
A
H