Hans Grohe Crometta S Showerpipe 240 1jet 26178007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / Assembly instructions 4
Lesezeichen
中文 2
English 4
Crometta S Showerpipe 240 1jet
26178007

2
中文
安全技巧
装配时为避免挤压和切割受伤,必须戴上手套.
本产品只允许作为洗浴,卫生和洁身之用.
不得让儿童和肢体,精神和/或意识有障碍的成
人在不受监管的情况下使用淋浴系统.受酒精或
毒品影响的人员不得使用淋浴系统.
头顶花洒夹持杆只为夹持头顶花洒而设计,不得
让其承载其它物品!
必须避免让身体敏感部位(如眼睛)接触到莲蓬
头喷水.必须保持莲蓬头与人头之间有足够的距
离.
该产品不得作扶柄使用.必须安装单独的扶柄.
冷热水管间过大的压力差必须予以平衡.
安装提示
• 安装前必须检查产品是否受到运输损害.安装后
将不认可运输损害或表面损伤.
• 管道和阀门必须根据通用标准进行安装,冲洗和
检查.
• 请遵守当地国家现行的安装规定.
• 本安装说明中所规定的安装尺寸理想用于身高
1700mm左右的人士.尺寸可根据需要进行修
改.在这种情况下,您必须留意,如果安装高度改
变,则花洒到地板的最小高度也随之改变,且必
须考虑到连接尺寸的改变.
• 由有资格的专业人员进行产品安装时请注意:在
所有加固区域中,加固表面是否平整(无突出的
接缝或瓷砖),墙体结构是否适合产品安装且未显
露出任何缺点.
• 必须装上花洒所附带的滤网密封垫,以过滤管道
里的杂质污物.杂质污物会影响花洒的功能和/
或损坏花洒的功能部件,由此而产生的产品损坏
不属于汉斯格雅的保修范围.
• 本产品并非设计来与蒸气浴连接使用!
• 紧急情况下,可使用细的锯子将下方区域中阀门
与头顶莲蓬头之间的管子锯短.
技术参数
工作压强: 最大1MPa
推荐工作压强:0,15-0,5MPa
测试压强:1,6MPa
(1MPa=10bar=147PSI)
热水温度: 最大60°C
中心距离:150±12mm
连接管线G1/2: 左热右冷
热力消毒:70°C/4分钟
• 自动防止回流
• 该产品专为饮用水设计!
符号说明
请勿使用含有乙酸的硅胶!
调节 (参见第页10)
热水温度调节.如果使用即热式喷头,则不建议安
装热水阀门.
保养 (参见第页11 )
单向阀必须在符合国家或当地的法律的情况下按照
EN806-5定期检查(至少一年一次).
大小 (参见第页14)
流量示意图 (参见第页15)
备用零件 (参见第页20)
选装附件 (不在供货范围内)
• 匹配瓷砖的圆盘#95239000
(参见第页20)
清洗 (参见第页16)
操作 (参见第页12)
请在使用喷头后略微倾斜,排空其中水分.

3
中文
安装 (参见第页6)
问题 原因 补救
龙头出水量小 - 单向阀装反 - 正确安装单向阀
- 花洒滤网有垃圾堵塞 - 清洗花洒和软管间的过滤网
龙头不灵活 - 阀芯损坏,结垢 - 更换阀芯
龙头滴水 - 阀芯损坏 - 更换阀芯
热水温度过低 - 温度限制器设置错误 - 设置温度限制器
燃气热水器不工作 - 手持花洒的流量限制器没有去除 - 去除流量限制器
- 花洒滤网有垃圾堵塞 - 清洗花洒和软管间的过滤网
- 单向阀装反 - 正确安装单向阀

4
English
Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
Children as well as adults with physical, mental and/
or sensoric impairments must not use this product
without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from
using this product.
The arm of the shower head is intended only to hold
the shower head. Do not load it down with other
objects!
Do not allow the streams of the shower touch sensitive
body parts (such as your eyes). An adequate distance
must be kept between the shower and you.
The product may not be used as a holding handle. A
separate handle must be installed.
The hot and cold supplies must be of equal pressures.
Installation Instructions
• Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
• The pipes and the fixture must be installed, flushed
and tested as per the applicable standards.
• The plumbing codes applicable in the respective
countries must be observed.
• The installation dimensions stated in these installation
instructions are ideal for people of approximately
1700 mm in body height. The dimensions can be
altered if required. In this case, pay attention to the
fact that a change of installation height will also
change the minimum height, and that the altered
mounting dimensions must be taken into considera-
tion.
• During installation of the product by qualified trained
personnel, make sure that the entire fastening surface
is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply
the product and has no weak points.
• The mesh washer must be insert to protect the shower
against incoming dirt by pipework. Incoming dirt
leads to defects or/and can damage parts of the
shower; such caused faults voids all liability and
guarantee claims.
• The product is not designed to be used with steam
baths!
• If required, the bottom part of the pipe between the
fixture and the shower head can be shortened with a
fine-toothed saw.
Technical Data
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,15 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Centre distance: 150±12 mm
Connections G 1/2: cold right - hot left
Thermal disinfection: 70°C / 4 min
• Safety against backflow
• The product is exclusively designed for drinking
water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 10)
To adjust the hot water limiter. Using a hot water limiter in
combination with a continuous flow water heater is not
recommended.
Maintenance (see page 11 )
The check valves must be checked regularly according to
EN 806-5 in accordance with national or regional
regulations (at least once a year).
Dimensions (see page 14)
Flow diagram (see page 15)
Spare parts (see page 20)
Special accessories (order as an extra)
• tile-matching-disk #95239000
(see page 20)
Cleaning (see page 16)
Operation (see page 12)
To empty the overhead shower after use, hold it in a
slightly inclined position.

5
English
Assembly (see page 6)
Fault Cause Remedy
Insufficient water - check valve hasn't moved back - Exchange check valves
- Shower filter seal dirty - Clean filter seal between shower
and hose
Mixer stiff - Cartridge defective, calcified - Exchange cartridge
Mixer dripping - Cartridge defective - Exchange cartridge
Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter
Instantaneous heater didn’t work - Flow limiter in handshower isn’t
removed
- Remove flow limiter
- Shower filter seal dirty - Clean filter seal between shower
and hose
- check valve hasn't moved back - Exchange check valves

6
1.
2.
X + 36 mm
X 36
X
1. 2.
36 mm max.
39 mm
max.
5 mm
SW 24 mm
1 2
3a
4 5
3b
Montage

7
Armaturenfett
Grease
䀵滑油
2.
1.
Armaturenfett
Grease
䀵滑油
3.
2.
1.
SW 30 mm
(17 Nm)
6 7
8 9
10 11
Montage

8
60 mm
Ø 6 mm
1.
2.
3.
12 13
14 15
16
Montage

9
SW 3 mm
(4 Nm)
1.
2.
3.
#94246000
#94246000
SW 17 mm
(10 Nm)
17 18
19
Montage

0,3 MPa
60 °C 10 °C
10
Justierung
+
+
21 3
4 5
6 7
4.
3.
1.
2.
3.
1.
2.
6 x
36°C
38°C
43°C
50°C
55°C
60°C
17 x
SW 4 mm
SW 4 mm
(5 Nm)
SW 4 mm
SW 4 mm