Landoll Brillion 3630-25 User manual

®
F-984-0418
LANDOLL CORPORATION
1900 North Street
Marysville, Kansas 66508
[phone]
800-428-5655 ~ WWW.LANDOLL.COM
s
3630-25 Coil Tine Harrow Kit 213907
3630-30NC Coil Tine Harrow Kit 213908
Instruction Sheet

1

CAUTION
Unfold, lower the unit to the ground.
Kit 213907 is for the 3630-25 Model.
Kit 213908 is for the 3630-30NC Model.
Installation
To ensure alignment of assemblies, leave the nuts
loose until completion of final assembly. Use washers as
specified.
After completion of final assembly, tighten all nuts
evenly to prevent misalignment, distortion or binding.
Tighten all screws and nuts to the recommended torques.
Refer to the operator’s manual for general torque
specifications.
Rotate Harrow 3 x 3 Tube
1. The 3 x 3 Tube inside the Harrow Assembly is
shipped with the tube horizontal. Remove the
Carriage Bolts that bolts the brackets to the Harrow
plates and rotate the 3 x 3 Tube as shown below.
Re-insert Carriage Bolts and secure.
Figure 1-1: Rotate Harrow 3 x 3 Tube
Do not work on or under this machine unless
securely blocked and supported by a hoist or
tractor or by other sufficient means.
Tube 3 x 3
Remove Carriage Bolts
Rotate 3 x 3 Tube as shown
Re-Insert Carriage Bolts
3630 CoilHarrowSide

2F-984-0418
Harrow Arm Installation
1. Refer to Figures 1-4, 1-6 and 1-7 for Harrow Arm
positioning. Note: Wing Harrow Arms are different
than Center Frame Harrow Arms.
2. Position the Arm Assembly onto the rear of the tube.
Place four hole plate on opposite side and slide four
bolts through plate holes into Arm Assembly. Secure
with Flange Nuts. See Figure 1-2.
Figure 1-2: Harrow Arm Installation to Frame
Plate
Bolt
Center Frame Rear Roller Tube
or Wing Frame Tube
Flange Nut
Arm Assembly
Flange Nut

3
3. Attach the Harrow Assembly to the Harrow Arm
Assembly by placing the 3 x 3 tube into the Arm
Notch.
Position U-bolt onto 3 x 3 tube and through the Harrow
Arm Assembly.
Secure with Thick Washer and Flange Nut. See
Figure 1-3.
Figure 1-3: Harrow Arm Installation to Harrow Assembly
Harrow Assembly
U-Bolt
Harrow Assembly
3 x 3 Tube
Arm Assembly
Thick Washer
Flange Nut

4F-984-0418
Figure 1-4: 3630-25 Center Rear Harrow Mounting Dimensions






+DUURZ$VVHPEO\
31
+DUURZ$VVHPEO\
31
+DUURZ$UP$VVHPEO\
31

5
Figure 1-5: 3630-30NC Center Rear Harrow Mounting Dimensions






+DUURZ$VVHPEO\
31
+DUURZ$VVHPEO\
31
+DUURZ$UP$VVHPEO\
31

6F-984-0418
Figure 1-6: 3630-25 Wing Rear Harrow Mounting Dimensions



+DUURZ$VVHPEO\
31
5+:LQJ)UDPH
5HDU7XEH




+DUURZ$VVHPEO\
31
/+:LQJ)UDPH
5HDU7XEH

+DUURZ$UP$VVHPEO\
31

Figure 1-7: 3630-30NC Wing Rear Harrow Mounting Dimensions



+DUURZ$VVHPEO\
31
5+:LQJ)UDPH
5HDU7XEH




+DUURZ$VVHPEO\
31
/+:LQJ)UDPH
5HDU7XEH

+DUURZ$UP$VVHPEO\
31

8F-984-0418
Table provided for general use.
NOTES: