Harbor Breeze E-BDB52LABZ5BC4N User manual

Harbor Breeze® is a registered trademark
of LF, LLC. All Rights Reserved.
ITEM #0152426
0156738
0158620
0204925
SPRINGFIELD II CEILING FAN
Español p. 21
1
MODEL #E-BDB52LABZ5BC4N
E-BDB52BNK5BC4N
E-BDB52LW5BC4N
E-BDB52MBK5BC4N
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-643-0067, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. -
5 p.m., EST, Friday.
EB15409 Lowes.com/harborbreeze
E124404
LISTED

Safety Information ...............................................................................................................2
Package Contents ...............................................................................................................4
Hardware Contents
.......................................................................................................................... 5
Preparation ..........................................................................................................................5
Initial Installation ..................................................................................................................6
Downrod-Style Fan Mounting ..............................................................................................8
Closemount-Style Fan Mounting .......................................................................................10
Wiring ................................................................................................................................
. 11
Final Installation ................................................................................................................
. 13
Operating Instructions .......................................................................................................16
Care and Maintenance ......................................................................................................18
Troubleshooting..................................................................................................................18
Limited Lifetime Warranty ..................................................................................................19
Replacement Parts List .....................................................................................................20
TABLE OF CONTENTS
2
Lowes.com/harborbreeze
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate the
product.
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the
floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 20.72 lbs.
SAFETY INFORMATION

SAFETY INFORMATION
3Lowes.com/harborbreeze
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. (15.9 KG) OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for the
support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a
plastic outlet box. Secure the outlet box directly to the building structure. The outlet box and its
support must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with
sharp edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blade arms when
installing them, balancing the blades or cleaning the fan. Do not insert objects between the
rotating fan blades.
To reduce the risk of personal injury, use ONLY parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before installation, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
WARNING
DANGER
CAUTION
When using an existing outlet box, make sure the outlet box is securely attached to the building
structure and can support the full weight of the fan. Failure to do this can result in serious injury or
death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure they are secure.

N Clip (preassembled) 1
O Switch Housing Cap 1
(preassembled)
P Switch Housing Screw 3
(preassembled)
Q Light Kit Fitter Screw 3
(preassembled)
R Light Kit Fitter 1
S Socket Ring (preassembled) 4
T Balancing Kit 1
U Star Washer (preassembled) 4
IMPORTANT REMINDER: You must use
the parts provided with this fan for proper
installation and safety.
PACKAGE CONTENTS
4
Lowes.com/harborbreeze
A Downrod 1
B Canopy 1
C Mounting Bracket 1
(preassembled)
D Motor Housing 1
E Glass Shade 4
F Blade 5
G Blade Arm 5
H Pull Chain Extension 2
I Motor Screw 1 0
(preassembled) + 1 extra
J Bulb 4
K Lock Washer 10
(preassembled) + 1 extra
L Canopy Mounting Screw 4
(preassembled)
M Pin (preassembled) 1
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
JE
D
K
L
H
C
I
AM
S
Q
O
P
R
B
N
U
G
F
T

5
HARDWARE CONTENTS (shown actual size)
Lowes.com/harborbreeze
Fiber
Blade
Washer
Qty. 15
+ 1 extra
CC
Blade
Screw
Qty. 15
+ 1 extra
E3 Wire
Connector
Qty. 4
AA BB CC
PREPARATION
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to install, operate or assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required forAssembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and
Wire Cutters

6
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
2.
3.
Determine mounting method to use.
A. Downrod mount (standard or angled ceiling)
B. Closemount (standard ceiling only)
IMPORTANT:If using the angle mount, check to
make sure the ceiling angle is not steeper than 19°.
*Helpful Hint: Downrod-style mounting is best
suited for ceilings 8 ft. or higher. For taller ceilings
you may want to use a longer downrod (not
included). Angle-style mounting is best suited for
angled or vaulted ceilings. A longer downrod is
sometimes necessary to ensure proper blade
clearance.
7 ft.
min.
30 in.
min.
F
INITIAL INSTALLATION
ON
OFF
ON
OFF
3
1
Lowes.com/harborbreeze
A
B
2
19° max.
Check to make sure blades (F) will be at least
30 in. from any obstruction and at least 7 ft.
above the floor.

Secure mounting bracket (C) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE:It is very important you use the proper
hardware when installing the mounting bracket
(C) as this will support the fan.
IMPORTANT: If using the angle mount, make
sure open end of mounting bracket (C) is
installed facing the higher point of the ceiling, and
ensure the ceiling angle is not steeper than 19°.
4b.
INITIAL INSTALLATION
7
Lowes.com/harborbreeze
5. Remove motor screws (I) and lock washers (K)
from underside of motor housing (D). [If there are
plastic motor blocks installed with the motor
screws (I) and lock washers (K), discard the
plastic motor blocks.]
For DOWNROD-STYLE FAN MOUNTING,
proceed to step 1 on the following page. For
CLOSEMOUNT-STYLE FAN MOUNTING, skip to
page 10.
4b
Open End
C
C
ANGLE MOUNTSTANDARD MOUNT
K
I
5
D
Plastic Motor Block
4a. Loosen canopy mounting screws (L) in slotted
holes of canopy (B) and remove the other two
canopy mounting screws (L) and star washers
(U). Save for later use.
Remove mounting bracket (C) from canopy (B).
4a CL
B
U

2. Insert downrod (A) through canopy (B). Thread
wires from motor housing (D) up through downrod
(A).
3.
A
N
M
DOWNROD-STYLE FAN MOUNTING
8
3
Lowes.com/harborbreeze
1.
Slip downrod (A) into yoke, align holes and
re-install pin (M) and clip (N). Tighten set screws in
yoke and then tighten nuts on the set screws.
Set
Screw
and Nut
B
A
2
Remove pin (M) and clip (N) from downrod (A).
Partially loosen preassembled set screws and nuts
in yoke at top of motor housing (D).
1
N
M
A
Yoke
Set Screw
and Nut
Sideview
D

Depending on the length of downrod you use,
you may need to cut the lead wires back to
simplify the wiring. If you decide to cut back the
lead wires, it is suggested you do so in the
following manner:
Take the lead wires and make sure you have
pulled them all the way through the top of the
downrod. Start at the TOP of the ball on the
downrod and measure 8 in. of lead wire, and
then cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 4 and 5 are not necessary and you may
proceed to Step 6 instead.
4.
Ball
5.
Install ball end of downrod (A) into opening of
mounting bracket (C). Align slot in ball with tab in
mounting bracket (C).
DANGER: Failure to align slot in ball with tab
may cause the fan to wobble or fall, which could
result in serious injury or death.
6.
Continue to WIRING on page 11.
A
C
A
DOWNROD-STYLE FAN MOUNTING
4
9
5
6
Lowes.com/harborbreeze
If you decided to cut back the lead wires in Step 4,
strip 1/2 in. of insulation from end of white wire.
Twist stripped ends of each strand of wire within
the insulation with pliers (not included). Repeat
Step 5 for black, blue (if applicable) and green
wires.
Slot
Tab

Remove canopy cover from bottom of canopy (B).
[NOTE: It may be necessary to use the handle
end of a screwdriver (not included) to remove the
canopy cover by tapping on the canopy cover
from the inside of the canopy (B).]
*Helpful Hint: Closemount-style mounting is
more suitable for ceilings lower than 8 ft. high.
The downrod (A) and canopy cover are not used
in this type of installation.
1.
Canopy
Cover
Remove every other screw and lock washer from
top of motor housing (D).
2.
3.
B
CLOSEMOUNT-STYLE FAN MOUNTNG
D
B
1
10
3
Lowes.com/harborbreeze
Pull wires up through hole in the middle of the
canopy (B) and attach canopy (B) to motor
housing (D) using the three screws and three lock
washers previously removed.
2
D
B
D