Harbor Breeze GAT24MBK6LOD User manual

GASKIN CEILING FAN
ITEM #2889555
MODEL #GAT24MBK6LOD
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could
also contact us at [email protected] or visit www.lowespartsplus.com
Purchase Date
1
Español p. 16
ATTACH YOUR RECEIPT HERE
ADJUNTE SU RECIBO AQUÍ
Harbor Breeze® and logo design are
trademarks or registered trademarks
of LF, LLC. All Rights Reserved.
JS20025
4007498
APPROVED FOR USE IN
WET LOCATIONS

TABLE OF CONTENTS
2
Modifications not approved by the party responsible for compliance could void the user's authority to
operate the equipment.
*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75053
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, (2) this device must accept any
interference received, including interference that may cause undesired operation.
SAFETY INFORMATION
Safety Information ........................................................................................................................ 2
Package Contents ........................................................................................................................ 5
Hardware Contents ...................................................................................................................... 6
Preparation .................................................................................................................................
.. 6
Initial Installation ........................................................................................................................... 7
Final Installation ............................................................................................................................ 9
Operating Instructions .............................................................................................................. 12
Troubleshooting.........................................................................................................................
.. 14
Care and Maintenance ............................................................................................................... 15
Limited Lifetime Warranty ..........................................................................................................
. 15
Replacement Parts List .............................................................................................................. 15

READ AND SAVE THESE INSTRUCTIONS
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to
the floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan including the light kit is: 13 lbs.
SAFETY INFORMATION
3
DO NOT suspend any fixture by the house wires. Fan must always be mounted
directly to an eye bolt which is first attached to the building structure. The power cord
alone will not support the weight of the fan. Suspending a fan by the plug will result in
the fan falling, with the possibility of personal injury and the danger of electrical shock or fire.
Secure the eye bolt directly to the building structure. The eye bolt and its support must be able to
support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp
edges.
To reduce the risk of fire or electrical shock, do not use the fan with any solid-state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when
installing or balancing them or cleaning the fan. Do not insert objects between the rotating fan
blades.
WARNING
DANGER
When using an eye bolt, make sure the eye bolt is securely attached to the building structure
and can support the full weight of the fan. Failure to do this can result in serious injury or death.
The stability of the eye bolt is essential in minimizing wobble and noise in the fan after installation
is complete.
To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the
fan, including the blades.
If using this fan in a WET location, connect this product to a Ground Fault Circuit Interrupting
(GFCI) outlet to reduce the risk of personal injury, electrical shock or death. If one is not provided,
contact a qualified electrician for proper installation.

4
SAFETY INFORMATION
CAUTION
Read all instructions and safety information before installing your new fan. Review the
accompanying assembly diagrams.
Once installation is complete, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
Do NOT tamper with or attempt to repair LED component. The light source is designed for this
specific application and should not be serviced by untrained personnel. If any servicing is
required, call our customer service department.
This portable fan has a polarized plug (one blade is wider than the other) as a safety feature to
reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If it does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. NEVER use
with an extension cord unless the plug can be fully inserted. DO NOT alter the plug.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
To reduce the risk of electric shock, DO NOT use the product if power cord is frayed or broken.
To reduce the risk of burns, fire, electric shock or injury to persons, unplug from outlet before
putting on or taking off parts.
As a safety precaution, unplug power supply cord when not in use.
DO NOT use staples or nails to secure wiring/power supply cord from light fixture.
DO NOT place wiring/power supply cord on sharp hooks or nails.
DO NOT hang ornaments or other objects from power supply cord, wire or lights.
DO NOT close doors and/or windows on the light fixture power supply cord as doing so may
damage the insulation wire(s).
WARNING

A
B
D
I
H
G
IMPORTANT REMINDER: You must use the
parts provided with this fan for proper installation
and safety.
A Downrod 1
B Motor Housing 1
C Yoke Cover 1
D LED Light Kit 1
E Blade 6
F Switch Housing 1
G Shade 1
HPin (preassembled) 1
DESCRIPTIONPART QUANTITY
PACKAGE CONTENTS
5
C
K
DESCRIPTIONPART QUANTITY
I Clip (preassembled) 1
J Blade Arm 6
K Switch Housing Screw 3
(preassembled)
L Motor Plate Screw 3
(preassembled)
M Motor Screw/Lock Washer 12
(preassembled) + 1 extra
F
E
J
M
L

6
PREPARATION
HARDWARE CONTENTS (shown actual size)
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list. If
any part is missing or damaged, do not attempt to install, operate or assemble the product.
Estimated Assembly Time: 60 minutes.
Tools Required for Assembly (not included): Phillips Screwdriver, Pliers, Safety Glasses, Stepladder.
Helpful Tools (not included): AC Tester Light, Tape Measure.
AA BB
Blade
Screw
Qty. 18
+ 1 extra
CC
Rubber
Blade
Washer
Qty. 18
+ 1 extra
Zip Tie
Qty. 1
Clamp
Qty. 6
Pull Chain
Extension
Qty. 2
EE
DD

7
INITIAL INSTALLATION
1. Remove preassembled motor screws/lock washers
(M) from underside of motor housing (B). If there
are plastic motor blocks installed with the motor
screws/lock washers (M), discard the plastic motor
blocks.
Note: Make sure to keep loose hardware separate
to avoid confusion during installation.
1
M
B
Plastic
Motor
Block
Remove pin (H) and clip (I) from downrod (A).
Partially loosen preassembled set screws and nut
in motor housing yoke at top of motor housing (B).
2a. 2a
H
I
2b
A
Set Screw
Sideview
B
Yoke
2b.
3. Insert downrod (A) through yoke cover (C). Slip
downrod (A) into motor housing yoke, align holes
and re-install pin (H) and clip (I). Tighten set
screws in motor housing yoke and then tighten
preassembled nut on one of the set screws. Then,
slide yoke cover (C) down until it rests on top of
motor housing (B).
3
B
C
I
H
Yoke
H
I
Set Screw
and Nut
Sideview
A

8
INITIAL INSTALLATION
6. Remove liner from back of clamp (DD). Place
clamps (DD) alongside the path of the power cord
and insert power cord into clamps (DD), making
sure the cord does not hang in the way of the fan.
6
Hardware Used
Clamp x 6
DD
5. Clip downrod (A) to secured eye bolt. Check the
length of the power cord from the outlet to the fan
(do NOT plug in the fan). Using the zip tie (EE)
secure power cord slack to the side of the
downrod.
5
Hardware Used
Zip Tie x 1
EE
EE
4. 4
Secure an eye bolt (not included) to ceiling of
building structure.
*NOTE: It is very important you use the proper
hardware when installing the eye bolt as this will
support the fan.
DD
DD
A

9
FINAL INSTALLATION
DANGER: To reduce the risk of serious bodily
injury, DO NOT use power tools to assemble the
blades (E). If screws are overtightened, blades (E)
may crack and break.
Partially insert three blade screws (AA) along with
three rubber blade washers (BB) into holes in blade
(E) (labeled THIS SIDE UP) to attach blade arm (J) to
blade (E). Then, tighten each blade screw (AA)
starting with the one in the middle.
Repeat Step 2 for remaining blades (E) and blade
arms (J).
1.
Rubber Blade Washer x 18
BB
Hardware Used
1
BB
AA
E
J
AA Blade Screw x 18
B
2
E
J
Attach blade arms (J) to the bottom of motor housing
(B) with motor screws/lock washers (M) previously
removed (Step 1, page 6). Tighten motor screws/lock
washers (M) securely.
NOTE: Make sure to completely secure each blade
arm (J) before proceeding to the next.
2.
M
3. Remove one motor plate screw (L) from motor
plate preassembled on the underside of the motor
housing (B) and partially loosen the other two
motor plate screws (L). Align slotted holes in
switch housing (F) with loosened motor plate
screws (L), allowing molex connections from
motor housing (B) to come through hole in switch
housing (F). Twist switch housing (F) to lock.
Re-insert the motor plate screw (L) that was
removed and securely tighten all three motor plate
screws (L).
3
I
L
I
L
I
L
F
B
Motor
Plate

10
FINAL INSTALLATION
4. Remove two switch housing screws (K) from
underside of switch housing (F) and partially
loosen the other switch housing screw (K).
3
4
K
K
F
D
molex
connections
6
Connect WHITE molex wire from LED light kit (D)
to WHITE molex wire from switch housing (F).
Connect BLUE molex wire from LED light kit (D) to
BLACK (or BLUE) molex wire from switch housing
(F). Make sure molex wire connections snap
together securely.
6.
F
5. Connect male plug from motor housing (B) to female
plug from switch housing (F), matching up the colors
on the male plug with the colors on the female plug
for correct fit. Make sure plugs are connected
completely.
5
B
Male
Plug
Female
Plug
F