Harbor Breeze CEDAR HILL User manual

Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-527-1292, 8:30 a.m.-5 p.m., CST, Monday-Friday.
ITEM #0312115
MODEL #PEH44BCW5MC
CEDAR HILL CEILING FAN
español p. 17
Harbor Breeze® is a registered trademark
of LF, LLC.All Rights Reserved.
E206035
1

2
TABLE OF CONTENTS
Safety Information ........................………………………………………………………......….3
Package Contents .............................…………………………………………………………..4
Hardware Contents .............................…………………………………………………...........5
Preparation .......................................….…………………..……………………….…..........6
Initial Installation ............................................……………………...………..................6 - 7
Wiring ...............................................................................................……......................8 - 9
Final Installation ............………………….………….....................................................9 - 12
Fan Operation ..............................................……………………………...….....…..............13
Care and Maintenance .......................………………………......………...….....…..............13
Troubleshooting ...........................................………...……………………..….........…........14
Warranty ........................…………………………………….………………..............…......….15
Replacement Parts List .......................………………………......………...….....….............16

3
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or operate
the product. If you have any questions regarding the product, please call customer service at
1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.
1. Before you begin installing the fan, disconnect the power by removing fuses or turning off
circuit breakers
.
2. CAUTION: Read all instructions and safety information before installing your new fan.
Review the accompanying assembly diagrams.
3.
CAUTION: To avoid personal injury, the use of gloves may be necessary while
handling fan parts with sharp edges.
4. Make sure that all electrical connections comply with local codes, ordinances, the National
Electrical Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a
do-it-yourself wiring handbook, available at Lowe's, if you are unfamiliar with installing
electrical wiring.
5. Make sure the installation site you choose allows a minimum clearance of 7 feet from the
blades to the floor and at least 30 in. from the end of the blades to any obstruction.
6. WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount fan to
outlet box marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided
with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are
not acceptable for fan support and may need to be replaced. Consult a qualified electrician if
in doubt. Secure the outlet box directly to the building structure. The outlet box and its support
must be able to support the moving weight of the fan (at least 35 lbs.). Do NOT use a plastic
outlet box.
7. After you install the fan, make sure that all connections are secure to prevent the fan from
falling.
8. WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire
connectors provided with this fan are designed to accept only one 12 gauge house wire and
two lead wires from the fan. If your house wire is larger than 12 gauge or there is more than
one house wire to connect to the two fan lead wires, consult an electrician for the proper size
wire connectors to use.
9. WARNING: To reduce the risk of fire or electric shock, do not use the fan with
any solid state speed control device or control fan speed with a full range dimmer
switch.
10. WARNING: To reduce the risk of fire, electric shock, or personal injury, do not bend
the blade arms when installing them, balancing the blades, or cleaning the fan. Do not insert
objects between the rotating fan blades.
11. WARNING: To reduce the risk of personal injury, use only parts provided with this
fan. The use of parts OTHER than those provided with this fan will void the warranty.
12. The net weight of this fan including the light kit is: 16.12 lbs. (7.31 kg).

4
PACKAGE CONTENTS
Part Description Quantity
A Motor Housing 1
B
Mounting Plate 1
C Switch Housing Cap (pre-attached to motor assembly) 1
D
Motor Assembly 1
E Light Kit Fitter 1
F Glass Shade 1
G
Blade Arm 5
H Blade 5
I Candelabra Base Bulb 3
J Pull Chain Extension (in hardware pack) 2
K Finial Plate (pre-attached to light kit fitter) 1
L Finial (pre-attached to light kit fitter) 1
IMPORTANT REMINDER: You must use
the parts provided with this fan for proper
installation and safety.
AC
I
H
F
G
DE
B
J K
L

HARDWARE CONTENTS
Part Description Quantity Part Shown to Size
Motor Screw (10 in motor; 1 in hardware pack) 11
3/16 Blade Screw (in hardware pack) 16
5.4M/M Lock Washer (10 in motor; 11
1 in hardware pack)
Blade Washer (in hardware pack) 16
E3 Wire Connector (in hardware pack) 4
Motor Assembly Mounting Screw 3
(pre-attached in mounting plate)
Lock Washer (for use with Part FF) 3
(pre-attached in mounting plate)
Hex Nut (pre-attached to light kit fitter) 1
Lock Washer (pre-attached to light kit fitter) 1
AA
5
GG
II
BB
CC
DD
EE
FF
HH

PREPARATION
1. Before beginning assembly, installation or operation of product, make sure all parts are
present. Compare parts with package contents list and diagram above. If any part is missing or
damaged, do not attempt to assemble, install or operate the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included):
electrical Phillips pliers safety stepladder wire
tape screwdriver glasses strippers
Helpful Tools (not included):
A/C tester tape do-it-yourself wiring handbook
light measure (available at Lowe’s) wire cutters
Bulbs Required (included):
3 candelabra base
40 watt max. bulbs
DANGER: When using an existing outlet box, make sure the outlet box is securely
attached to the building structure and can support the full weight of the fan. Failure to do this can
result in serious injury or death. The stability of the outlet box is essential in minimizing wobble
and noise in the fan after installation is complete.
CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire
is present.
2. After opening top of carton, remove mounting hardware package from foam inserts. Remove
motor from packing and place on carpet or on foam to avoid damage to finish.
CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that
they are secured.
A-15
1. Turn off circuit breakers and wall switch to the fan supply
line leads. (Fig. 1)
DANGER: Failure to disconnect power supply prior
to installation may result in serious injury or death.
6
INITIAL INSTALLATION
2. Check to make sure blades (H) will be at least 30 in. from
any obstruction and at least 7 ft. above the floor. (Fig. 2)
7 ft.
min.
30 in.
min.
Fig. 1
Fig. 2 H

7
INITIAL INSTALLATION
4. Secure mounting plate (B) to outlet box
using screws, spring washers, and flat
washers provided with the outlet box. (Fig. 4)
Pull wires from outlet box through center hole
in mounting plate (B).
*Note: It is very important that you use the
proper hardware when installing the
mounting plate (B) as this will support the
fan.
5. Remove motor screws (AA) and lock
washers (CC) from underside of motor--save
to attach blade arms (G) later on. If there are
also plastic motor blocks, discard them at
this time. (Fig. 5)
Motor
Red Dot
6. Use the square hole in the plate at the top
of the motor assembly (D) and slide it over
the "J" hook on the mounting plate (B) to
support the fan during wiring. (Fig. 6)
Hint: Place square hole in motor assembly
(D) over “J” hook in mounting plate (B). While
keeping the motor assembly (D) flush with
the mounting plate (B), slide motor assembly
(D) onto “J” hook.
Square Hole
B
D
B
CC
AA
D
3. Locate motor assembly mounting screws
(FF) on underside of mounting plate (B).
Remove the motor assembly mounting screw
(FF) with a red dot, along with the lock
washer (GG)--save for later use. Partially
loosen the other two motor assembly
mounting screws (FF). (Fig. 3)
B
Fig. 3
Fig. 4
Fig. 5
Fig. 6
CC
AA
Motor Screw x 10
Hardware Used
5.4 M/M Lock Washer x 10
GG
FF
Motor Assembly x 3
Mounting Screw
Hardware Used
Lock Washer x 3
"J" Hook
GG GG
FF
FF

Caution: Be sure wiring box is properly grounded
and that a ground (green or bare) wire is present.
8
WIRING
Fig. 1C
1. Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C) that
fits your situation and make appropriate wiring connections
as follows: [NOTE: For each wire connection below, use
one of the wire connectors (EE) provided, making sure to
screw wire connector (EE) on in a clockwise direction.]
1A. FAN AND LIGHT CONTROLLED BY PULL
CHAINS: Connect BLACK and BLUE wire from fan to
BLACK wire from ceiling. Connect WHITE wire from fan
to WHITE wire from ceiling. Connect all GROUND
(GREEN) wires together from fan (on motor assembly
and mounting plate) to BARE/GREEN wire from ceiling.
(Fig. 1A)
1B. FAN CONTROLLED BY PULL CHAIN, LIGHT BY
WALL SWITCH: If you intend to control the fan light with
a separate wall switch, connect BLACK wire from fan to
BLACK wire from ceiling. Connect BLUE wire from fan
to the BLACK wire from the independent wall switch for
the light. Connect WHITE wire from fan to WHITE wire
from ceiling. Connect all GROUND (GREEN) wires
together from fan (on motor assembly and mounting
plate) to BARE/GREEN wire from ceiling. (Fig. 1B)
1C. FAN AND LIGHT CONTROLLED BY TWO WALL
SWITCHES: If you intend to control the fan and light with
separate wall switches, connect BLACK wire from fan to
BLACK wire from the independent wall switch for the
fan. Connect BLUE wire from fan to the BLACK wire
from the other independent wall switch for the light.
Connect WHITE wire from fan to WHITE wire from
ceiling. Connect all GROUND (GREEN) wires together
from fan (on motor assembly and mounting plate) to
BARE/GREEN wire from ceiling. (Fig. 1C)
Fig. 1A
Warning: If house wires are different colors than
referred to in the following steps, stop immediately. A
professional electrician is recommended to determine wiring.
WARNING: To reduce the risk of fire, electrical
shock, or personal injury, wire connectors provided with
this fan are designed to accept only one 12 gauge house
wire and two lead wires from the fan. If your house wire is
larger than 12 gauge or there is more than one house wire
to connect to the two fan lead wires, consult an electrician
for the proper size wire connectors to use.
Note: Black wire is hot power for fan. Blue wire is hot
power for light kit. White wire is common for fan and light
kit. Green or bare wire is ground.
FAN AND LIGHT CONTROLLED BY PULL CHAINS
BLACK
WHITE
GROUND/GREEN (BARE)
WHITE
BLUE
WHITE
FROM FAN
120 V Power
FROM
CEILING
FAN CONTROLLED BY PULL CHAIN, LIGHT BY
WALL SWITCH
WHITE
BLACK
BLACK (WALL SWITCH)
GROUND/GREEN (BARE)
BLACK
BLUE
WHITE
FROM FAN
Fig. 1B
FAN
120 V Power
FROM
CEILING
WHITE
BLACK (WALL SWITCH)
BLACK (WALL SWITCH FOR LIGHT)
GROUND/GREEN (BARE)
BLACK
BLUE
WHITE
FROM FAN
FAN
120 V Power
FROM
CEILING
FAN AND LIGHT CONTROLLED BY TWO WALL
SWITCHES
GREEN
GREEN
GREEN
FAN
GREEN
GREEN
BLACK
GREEN
WHITE
WHITE

9
1. Gently swing motor assembly (D) up to mounting
plate (B), allowing slotted holes on plate at top of
motor assembly (D) to align with loosened motor
assembly mounting screws (FF) in mounting plate
(B). Twist motor assembly (D) to lock. Re-insert
motor assembly mounting screw (FF), along with
lock washer (GG), that was previously removed
(Step 3, page 7). Tighten all three motor assembly
mounting screws (FF) securely. (Fig. 1)
FINAL INSTALLATION
1
2
3
IMPORTANT: Using a full range dimmer switch to
control fan speed will cause a loud humming noise
from fan. To reduce the risk of fire or electric shock,
do NOT use a full range dimmer switch to control fan
speed. (Fig. 3)
Dimmer
Switch Speed
Switch
WIRING
2. Wrap electrical tape around each wire connector
(EE) down to the wire as shown in Fig. 2.
Warning: Make sure no bare wire or wire
strands are visible after making connections. Place
green and white connections on opposite side of box
from the black and blue (if applicable) connections.
Turn spliced/taped wires upward and gently push
wires and wire connectors (EE) into outlet box.
N
EE
EE
EE
EE
Hardware Used
E3 Wire Connector x 4
Fig. 2
Fig. 3
Fig. 1
GG
FF
Motor Assembly x 3
Mounting Screw
Hardware Used
Lock Washer x 3
For illustrative purposes only--not
intended to cover all types of controls
B
GG
D
FF

10
FINAL INSTALLATION
2. Locate three large screws at top of motor housing
(A). Align large screws with slots on the edges of the
mounting plate (B). Turn motor housing (A) clockwise,
to the RIGHT, until it no longer turns. (Fig. 2)
Note: It is extremely important that you make sure
that you turn the motor housing (A) all the way to
ensure that the motor housing (A) is completely
secure.
Fig. 2
3. Partially insert three blade screws (BB), along with
three blade washers (DD), to attach one blade arm
(G) to a blade (H). Then, tighten each blade screw
(BB), starting with the one in the middle (Fig. 3)
Repeat with remaining blades (H).
4. Insert two motor screws (AA), along with lock
washers (CC), through one blade arm (G) to attach
blade arm (G) to motor. Tighten motor screws (AA)
securely. (Fig. 4) Repeat with remaining blade arms
(G), making sure to completely secure each blade
arm (G) before proceeding with the next.
A
G
G
DD
BB
CC
AA
H
H
Fig. 3
DD
BB
3/16 Blade Screw x 15
Blade Washer x 15
Fig. 4
Hardware Used
CC
AA
Motor Screw x 10
Hardware Used
5.4 M/M Lock Washer x 10
Large
Screws A
B