Harbor Breeze EUK60MBK10LR User manual

Purchase Date
1
4007498
ITEM #2599787
1058853
HENDERSON LED
CEILING FAN
Español p. 20
MODEL # EUK60MBK10LR
EUK60GV10LR
ATTACH YOUR RECEIPT HERE
SM21655
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could also
contact us at [email protected].
HARBOR BREEZE and logo design are
trademarks or registered trademarks of LF, LLC.
All rights reserved.
APPROVED FOR USE
IN DAMP LOCATIONS
ADJUNTE SU RECIBO AQUÍ

2
Safety Information ...............................................................................................................
. . 2
Package Contents ..............................................................................................................
. .. 5
Hardware Contents
........................................................................................................................... 6
Preparation ........................................................................................................................... 6
Initial Installation ................................................................................................................... 6
Wiring .................................................................................................................................. 10
Final Installation ................................................................................................................... 12
Operating Instructions ......................................................................................................... 16
Care and Maintenance ...................................................................................................
. .... 17
Troubleshooting ................................................................................................................... 18
Limited Lifetime Warranty .................................................................................................... 19
Replacement Parts List ....................................................................................................... 19
TABLE OF CONTENTS
SAFETY INFORMATION
CAUTION: Changes or modifications not approved by the party responsible for compliance
could void the user's authority to operate the equipment.
*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, (2) this device must accept any
interference received, including interference that may cause undesired operation.
Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75050; 800-527-1292
NOTE: Dimmable to 10%.

3
SAFETY INFORMATION
The DC Motor will not operate until blades are installed.
READ AND SAVE THESE INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, install or
operate the product. Review the accompanying assembly diagrams.
• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for
repairs, it must be shipped in its original packaging to ensure proper protection against damage that
might exceed the initial cause for return.
• Make sure all electrical connections comply with local codes, ordinances, the National Electrical
Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring
handbook if you are unfamiliar with installing electrical wiring.
• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to the
floor and at least 30 in. from the end of the blades to any obstruction.
• After you install the fan, make sure all connections are secure to prevent the fan from falling.
• The net weight of this fan is: 29 lbs.
DANGER
When using an existing outlet box, make sure the outlet box is securely attached to the building
structure and can support the full weight of the fan. Failure to do this can result in serious injury or
death. The stability of the outlet box is essential in minimizing wobble and noise in the fan after
installation is complete.
To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the fan,
including the blades.
To reduce the risk of fire, electrical shock or personal injury, mount fan to outlet box
marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS. OR LESS" and use
mounting screws provided with the outlet box. Most outlet boxes commonly used for
the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box; do NOT use a plastic
outlet box. Secure the outlet box directly to the building structure. The outlet box and its support
must be able to support the moving weight of the fan (at least 35 lbs.).
To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp
edges.
To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan
are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
WARNING

4
CAUTION
Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.
Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
Once installation is complete, carefully check all screws, bolts and nuts on fan motor assembly to
ensure that they are secured.
Do NOT tamper with or attempt to repair LED component. The light source is designed for this
specific application and should not be serviced by untrained personnel. If any servicing is required,
call our customer service department.
Due to the weight and construction of this fixture, it is advisable to seek the help of another person.
To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed control
device or control fan speed with a full range dimmer switch.
To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when
installing or balancing them or when cleaning the fan. Do not insert objects between the rotating
fan blades.
To reduce the risk of personal injury, use only parts provided with this fan. The use of parts
OTHER than those provided with this fan will void the warranty.
Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid
electrical shock.
This fan MUST be installed with the safety cable provided with the fan. Failure to use the safety
cable provided may result in personal injury, damage to the fan or damage to other property.
WARNING
SAFETY INFORMATION

5
PACKAGE CONTENTS
DESCRIPTIONPART QUANTITY DESCRIPTIONPART QUANTITY
IMPORTANT REMINDER: You must use the parts provided with this fan for proper installation
and safety.
A
L
M
G
C
D
B
E
H
I
K
J
N
O
F
A Mounting Bracket 1
B Canopy Mounting Screw 2
(preassembled)
C Downrod 1
D Pin (preassembled) 1
EClip (preassembled) 1
F Canopy 1
G Canopy Cover 1
H Yoke Cover 1
I Motor Assembly 1
J Blade 10
K Blade Bracket 5
LBlade Bar 10
M Shade 1
N Remote Pack 1
O
Safety Cable (preassembled) 1
P
Remote Control Receiver 1
P

HARDWARE CONTENTS (shown actual size)
Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on
foam to avoid damage to finish. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety
Glasses, Stepladder, Wire Strippers and Precision Screwdriver (0 x 2 in.).
Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and
Wire Cutters.
PREPARATION
CC
Blade
Screw/Washer
Qty. 40
+ 1 extra
Wire
Connector
Qty. 3
AA BB CC
INITIAL INSTALLATION
ON
OFF
ON
OFF
1
Turn off circuit breakers and wall switch to the fan
supply line leads.
DANGER: Failure to disconnect power supply
prior to installation may result in serious injury or
death.
1.
Decorative
Nut
Qty. 20
+ 1 extra
6

INITIAL INSTALLATION
Check to make sure blades (J) will be at least
30 inches from any obstruction at least 7 ft. above
the floor.
3.
2. Determine mounting method to use.
A. Standard mount
B. Angle mount
IMPORTANT: If using the angle mount, ensure the
ceiling angle is not steeper than 19°.
NOTE: Closemount option is not available for this
fan.
*Helpful Hint: Downrod-style mounting is best
suited for ceilings 8 ft. high or higher. For taller
ceilings you may want to use a longer downrod
(not included). Angle-style mounting is best suited
for angled or vaulted ceilings. A longer downrod is
sometimes necessary to ensure proper blade
clearance.
2
B
A
7 ft.
min.
30 in.
min.
3
19° max.
4.
Open End
4ANGLE MOUNTSTANDARD MOUNT
Secure mounting bracket (A) to outlet box (not
included) using screws, spring washers and flat
washers provided with the outlet box.
*NOTE: It is very important you use the proper
hardware when installing the mounting bracket (A)
as this will support the fan.
IMPORTANT: If using the angle mount, make sure
open end of mounting bracket (A) is installed facing
the higher point of the ceiling, and ensure the
ceiling angle is not steeper than 19°.
7
J
A
A

INITIAL INSTALLATION
Remove pin (D) and clip (E) from downrod (C).
Partially loosen preassembled set screws and nuts
in yoke at top of motor assembly (I).
5a. 5A 5B
Set Screw
Sideview
Yoke
6. Insert downrod (C) through canopy (F), canopy
cover (G) and yoke cover (H). NOTE: Canopy
cover (G) must be turned with the shiny side
toward the motor assembly (I).
Then, thread wires and safety cable (O) from
motor assembly (I) through downrod (C).
6
7. Slip downrod (C) into yoke, align holes and
re-install pin (D) and clip (E). Tighten set screws
in yoke and then tighten preassembled nuts on
the set screws. Then, slide yoke cover (H) down
until it rests on top of motor assembly (I).
7
Yoke
E
D
Set Screw
and Nut
Sideview
5b.
8
E
I
D
C
H
G
F
O
C
D
I
H
E
C

INITIAL INSTALLATION
8.
9
Install hanging ball of downrod (C) into opening of
mounting bracket (A). Align one of the slots in
hanging ball with tab in mounting bracket (A).
DANGER: Failure to align one of the slots in
the ball with the tab may result in serious injury or
death.
Tab
10
Slot
If you decided to cut back the lead wires in Step 8,
strip 1/2 in. of insulation from end of each
wire -- WHITE, BLACK, AND GREEN (if
applicable). Twist stripped ends of each strand of
wire within the insulation with pliers (not included).
Depending on the length of downrod you use, you
may need to cut the lead wires back to simplify
the wiring. If you decide to cut back the lead
wires, it is suggested you do so in the following
manner:
Take the lead wires and make sure you have
pulled them all the way through the top of the
downrod. Start at the TOP of the hanging ball on
the downrod and measure 8 in. of lead wire, then
cut the excess wire off with wire cutters (not
included).
NOTE: If you do not cut back the lead wires,
Steps 8 and 9 are not necessary and you may
proceed to Step 10 instead.
Hanging
Ball
8
8 in.
9.
10.
9
C
A
C

Wood Screw,
Washer and
Lock Washer
Wood
Joist
Loop
11. 11
Find a secure attachment point (wood ceiling joist
recommended) and secure safety cable (O). Use a
heavy-duty wood screw, washer and lock washer
(not included) to secure safety cable (O) loop. The
loop at the end of the safety cable (O) should just
fit over the threads on the wood screw (not
included) used to secure it.
Test safety cable (O) by pulling on loose end of
cable with pliers. If the safety cable (O) slips, the
loop must be adjusted tighter.
NOTE: Extra cable slack can be left in ceiling area.
INITIAL INSTALLATION
WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors
provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to
the corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.
CAUTION: Be sure outlet box is properly grounded and that a ground (green or bare) wire is
present.
WARNING: If house wires are different colors than referred to in the following steps, stop
immediately. A professional electrician is recommended to determine wiring.
WARNING: Using a full range dimmer switch (not included) to control fan speed will cause a loud
humming noise from fan. To reduce the risk of fire or electrical shock, do NOT use a full range
dimmer switch to control fan speed.
WIRING
10
O
IMPORTANT: Make the necessary wiring connections for
remote control operation as detailed on next page. For each
wire connection, use one of the wire connectors from the
remote pack (R), making sure to screw wire connector on in
a clockwise direction.
Wire
Connectors
R