Harbor breeze Tiempo e-tm52bnk5cs User manual

TIEMPO/CEILING FAN

TIEMPO

/VENTILADOR DE TECHO (página 11)

ITEM/ARTICULO #0125453

MODEL/MODELO #E-TM52BNK5CS

Questions, problems, missing parts? Before returning to your retailer, call or contact our customer service

department at 1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.

Harbor Breeze® is a registered trademark

E192641

WARNINGS

• Read and save these instructions.

• Read this manual carefully and completely before attempting to assemble, install or operate this product.

• Be sure you read and understand the Safety Information on page 3 of these instructions.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for repairs, it must be

shipped in its original packaging to ensure proper protection against damage that might exceed the initial cause for

return.

• CAUTION: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

• WARNING: To reduce the risk of fire or electric shock, do not use this fan with variable speed switch.

• WARNING: To reduce the risk of fire, electric shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert foreign objects between the rotating fan

blades. Mount to outlet box marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan

support and may need to be replaced. Consult a qualified electrician if in doubt.

DEL

E-TM

registered

trademar

egi

ste

red

ade

mar

All Ri

hts Reserved.

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with

bulbs totaling more than 190W, the wattage limiting device will reduce the watts

consumed to 190W.

TIEMPO/CEILING FAN

TIEMPO

/VENTILADOR DE TECHO (página 11)

ITEM/ARTICULO #0125500

MODEL/MODELO #E-TM52BNKB5CS

Questions, problems, missing parts? Before returning to your retailer, call or contact our customer service

department at 1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.

Harbor Breeze® is a registered trademark

E192641

WARNINGS

• Read and save these instructions.

• Read this manual carefully and completely before attempting to assemble, install or operate this product.

• Be sure you read and understand the Safety Information on page 3 of these instructions.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for repairs, it must be

shipped in its original packaging to ensure proper protection against damage that might exceed the initial cause for

return.

• CAUTION: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

• WARNING: To reduce the risk of fire or electric shock, do not use this fan with variable speed switch.

• WARNING: To reduce the risk of fire, electric shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert foreign objects between the rotating fan

blades. Mount to outlet box marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan

support and may need to be replaced. Consult a qualified electrician if in doubt.

DEL

E-TM

registered

trademark

® is a registered trademark

All Ri

hts Reserved.

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with

bulbs totaling more than 190W, the wattage limiting device will reduce the watts

consumed to 190W.

ITEM/ARTICULO #0126663

TIEMPO/CEILING FAN

TIEMPO

/VENTILADOR DE TECHO (página 11)

MODEL/MODELO #E-TM52BNKR5CS

Questions, problems, missing parts? Before returning to your retailer, call or contact our customer service

department at 1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.

Harbor Breeze® is a registered trademark

E192641

WARNINGS

• Read and save these instructions.

• Read this manual carefully and completely before attempting to assemble, install or operate this product.

• Be sure you read and understand the Safety Information on page 3 of these instructions.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for repairs, it must be

shipped in its original packaging to ensure proper protection against damage that might exceed the initial cause for

return.

• CAUTION: Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

• WARNING: To reduce the risk of fire or electric shock, do not use this fan with variable speed switch.

• WARNING: To reduce the risk of fire, electric shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert foreign objects between the rotating fan

blades. Mount to outlet box marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan

support and may need to be replaced. Consult a qualified electrician if in doubt.

DEL

E-TM

is a re

istered trademark

All Ri

hts Reserved.

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with

bulbs totaling more than 190W, the wattage limiting device will reduce the watts

consumed to 190W.

TABLE OF CONTENTS

Safety Information ........................…………………………………………………………………………...……..….3

Package Contents .............................…………………………………………………………………..……..…..…..4

Preparation .......................................….…………………..……………………….…………….………………....5

Initial Installation ............................................……………………...…………………………………………...….5

Fan Mounting ........................…………………………....…………………………................................................6

Wiring .........................................................................................................……………………………….......6 - 7

Final Installation ............………………….…………….……………………….………….....….…....................7 - 8

Fan Operation ............................................................................................…………………………………....….8

Care and Maintenance .......................………………………………………………………………..…………….…9

Troubleshooting ...........................................………...………………………….……………..………....……..…...9

Warranty ........................…………………………………….…………………………………………..…………..….10

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the product. If you

have any questions regarding the product, please call customer service at 1-800-527-1292, 8:30 a.m.-5:00 p.m.,

CST, Monday-Friday.

1.Before you begin installing the fan, disconnect the power by removing fuses or turning off circuit breakers

2. CAUTION: Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

3. CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

4.Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code and

ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook, available at Lowe's, if

you are unfamiliar with installing electrical wiring.

5.Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to the floor and at

least 30 in. from the end of the blades to any obstruction.

6. WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box marked

"ACCEPTABLE FOR FAN SUPPORT OF 15.9 KG (35 LBS) OR LESS" and use mounting screws provided with the

outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support

and may need to be replaced. Consult a qualified electrician if in doubt. Secure the outlet box directly to the building

structure. The outlet box and its support must be able to support the moving weight of the fan (at least 35 lbs.). Do

NOT use a plastic outlet box.

7.After you install the fan, make sure that all connections are secure to prevent the fan from falling.

8. WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12 gauge house wire and two lead wires from the fan. If your house wire is

larger than 12 gauge or there is more than one house wire to connect to the two fan lead wires, consult an

electrician for the proper size wire connectors to use.

9. WARNING: To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

10. WARNING: To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the rotating fan blades.

11. WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

12. The net weight of this fan including the light kit is: 24.25 lbs. (11 kg).

PACKAGE CONTENTS

Part Description Quantity

NOTE:

For replacement parts, call our customer service department

at 1-800-527-1292, 8:30 a.m.-5:00 p.m., CST, Monday-Friday.

When ordering parts, please have the Model # or Item # of the

fan available, which can be found on page 1.

* The part denoted with an asterisk (*) above is NOT replaceable.

Glass Shade

Clip (attached to pin)

Candelabra Base Bulb

Pull Chain Extension (in hardware pack)

Motor Screw (in motor)

Canopy Mounting Screw (attached to mounting bracket)

3/16 Blade Screw (in hardware pack)

5.4M/M Lock Washer (in motor)

Blade Washer (in hardware pack)

E3 Wire Connector (in hardware pack)

Canopy

Motor Housing

Switch Housing Plate

Light Kit Fitter

Blade Arm

Downrod

Yoke Cover

Mounting Bracket

Blade

ABC

DEF

MNO

PQR

STU

Pin (in motor housing yoke)

Canopy cover (in hardware pack)

IMPORTANT REMINDER: You must use

the parts provided with this fan for proper

installation and safety.

INITIAL INSTALLATION

1. Turn off circuit breakers and wall switch to the fan supply line

leads. [Fig. 1]

DANGER: Failure to disconnect power supply prior to

installation may result in serious injury or death.

3. Check to make sure blades (I) are at least 30 in. from any

obstruction. Check downrod (A) length to ensure blades (I) are at

least 7 ft. above the floor. [Fig. 3]

PREPARATION

1. Before beginning assembly and installation of product, make sure all parts are present. Compare parts with

"Package Contents" list and diagrams on the previous page. If any part is missing or damaged, do not attempt to

assemble, install or operate the product. Contact customer service for replacement parts as indicated at the bottom

of page 4.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included):electrical tape, Phillips screwdriver, pliers, safety glasses, stepladder

and wire strippers

Helpful Tools (not included):AC tester light, tape measure, do-it-yourself-guide and wire cutters

Bulbs Required (included):4 candelabra base 40 watt max. bulbs

2. After opening top of carton, remove mounting hardware package from foam inserts. Remove motor from packing

and place on carpet or on foam to avoid damage to finish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they are secured.

DANGER: When using an existing outlet box, make sure the box is securely attached to the building

structure and can support the full weight of the fan. Failure to do this can result in serious injury or death.

Fig. 1

Fig. 3

Fig. 4

5. Remove motor screws (K) and lock washers (N) from underside

of motor. If necessary, discard plastic pieces. [Fig. 5]

Fig. 5

Fig. 2

2. Determine mounting method to use. [Fig. 2]

A. Normal mount

B. Angle mount

Important: If using the angle mount, check to make sure the

ceiling angle is not steeper than 19°.

7 ft.

min.

30 in.

min.

4. Secure mounting bracket (C) to outlet box using screws, spring

washers, and flat washers provided with the outlet box. [Fig. 4]

*Note: It is very important that you use the proper hardware when

installing the mounting bracket (C) as this will support the fan.

Important: If using the angle mount, make sure open end of

mounting bracket (C) is installed facing the higher point of the

ceiling.

WIRING (continued on next page)

Fig. 1

Fig. 2

FAN MOUNTING

3. Install ball end of downrod (A) into mounting bracket (C) opening. Align slot

in ball with tab in mounting bracket (C). [Fig. 3]

DANGER: Failure to align slot in ball with tab may result in serious injury

or death. Fig. 3

1. Insert downrod (A) through canopy (B) and yoke cover (F). Thread wires from

motor housing (D) through downrod (A). [Fig. 1]

*Helpful Hint: Downrod style mounting is best suited for ceilings 8 ft. (2.44 m)

high or higher. For taller ceilings you may want to use a longer downrod (not

included). Angle style mounting is best suited for angled or vaulted ceilings. A

longer downrod is sometimes necessary to ensure proper blade clearance.

Note: Black wire is hot power for fan. Blue wire is hot power for

light kit. White wire is common for fan and light kit. Green or bare

wire is ground.

SWITCHED LIGHT POWER

WHITE (NEUTRAL)

BLACK (POWER)

GROUND

WHITE

SWITCHED LIGHT POWER

WHITE (NEUTRAL)

GROUND

BLACK

BLUE

GROUND

WHITE

SWITCHED FAN POWER

FAN AND LIGHT CONTROLLED BY CHAIN.

FAN CONTROLLED BY CHAIN, LIGHT BY WALL SWITCH.

FANANDLIGHTCONTROLLED BYSEPARATE WALL SWITCHES.

BLACK (POWER)

WHITE (NEUTRAL)

GROUND

WHITE

Fig. 1A

Fig. 1B

Fig. 1C

WARNING: To reduce the risk of fire, electrical shock, or

personal injury, wire connectors provided with this fan are designed

to accept only one 12 gauge house wire and two lead wires from

the fan. If your house wire is larger than 12 gauge or there is more

than one house wire to connect to the two fan lead wires, consult

an electrician for the proper size wire connectors to use.

CAUTION: Be sure outlet box is properly grounded and that

a ground (green or bare) wire is present.

1. Choose wiring diagram [Fig. 1A, Fig. 1B or Fig. 1C] that fits your

situation and make appropriate wiring connections as follows:

(Make special note of Step 3 on the following page while wiring.)

1A. Connect BLACK and BLUE wire from fan to BLACK wire

from ceiling with wire connector (P) provided. Connect WHITE

wire from fan to WHITE wire from ceiling with wire connector (P)

provided. Connect all GROUND (GREEN) wires together from fan

to BARE/GREEN wire from ceiling with wire connector (P)

provided. [Fig. 1A]

1B. If you intend to control the fan light with a separate wall

switch, wire as indicated in the instructions in 1A except connect

BLUE wire from fan to the BLACK supply from the independent

switch. [Fig. 1B]

1C. If you intend to control the fan and light with separate wall

switches, wire as indicated in the instructions in 1A except

connect BLUE wire from fan to the BLACK supply from the

independent wall switch for the light and connect BLACK wire

from fan to the BLACK supply from the other independent wall

switch for the fan. [Fig. 1C]

WARNING: If house wires are different colors than referred

to in following steps, stop immediately. A professional electrician is

recommended to determine wiring.

BLACK

BLUE

BLACK

BLUE

Ball

[Fig. 2].

2. Insert downrod (A) through canopy (B), canopy cover (U), and yoke cover

(F). [Note: Canopy cover (U) must be turned with the shiny side toward the

motor housing (D).] Thread wires from motor housing (D) through downrod (A).

[Fig. 2] Remove pin (R) and clip (S) from motor housing yoke. Slip downrod (A)

into motor housing yoke, align holes and re-install pin (R) and clip (S). Tighten

downrod set screws and then tighten nuts. Slide yoke cover (F) down until it

rests on top of motor housing (D).

4. Screw wire connectors (P) on in a clockwise direction. Wrap

electrical tape around each wire connector (P) down to the wire as

shown in Fig. 4.

WARNING: Make sure no bare wire or wire strands are

visible after making connections. Place green and white connections

on opposite side of box from the black and blue (if applicable)

connections.

Turn spliced/taped wires upward and gently push wires and wire

connectors (P) into outlet box.

WIRING (continued from previous page)

2. Connect green wire from downrod (A) to green wire on mounting

bracket (C). [Fig. 2]

3. Strip 3/4 of an inch of insulation from ends of white wire. Twist

stripped ends of each strand of wire within the insulation with

pliers. [Fig. 3] Snip ends after twisting strands together. Repeat for

black, blue (if applicable) and green wires. Fig. 2

Fig. 3

FINAL INSTALLATION (continued on next page)

2. Position blade arm (H) under blade (I) and attach blade arm (H)

to blade (I) with blade screws (L) and blade washers (O). Do not

tighten blade screws (L) until each blade screw (L) has been

started. Then, tighten each blade screw (L) starting with the one in

the middle. [Fig. 2] Repeat for the remaining blades (I).

3. Insert only one motor screw (K), with lock washer (N), through

blade arm (H) to attach blade arm (H) to motor and partially tighten

motor screw (K). [Fig. 3] Repeat with remaining blade arms (H).

4. Insert remaining motor screws (K) with lock washers (N). [Fig. 4]

Tighten all motor screws (K) securely.

5. Partially loosen two screws on fitter plate on underside of motor

and remove the other screw. Align slotted holes in switch housing

plate (G) with loosened screws on fitter plate. Twist switch housing

plate(G) to lock. Re-insert the screw that was removed and securely

tighten all three screws. [Fig. 5]

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fitter Plate

Fig. 4

Fig. 1

1. Locate two canopy mounting screws (Q) on underside of mounting

bracket (C) and remove canopy mounting screw (Q) closest to the

open end of the hanging bracket (C). Partially loosen the other canopy

mounting screw (Q). Lift canopy (B) to mounting bracket (C). Place

rounded part of slotted hole in canopy (B) over loosened canopy

mounting screw (Q) in hanging bracket (C) and push up. Twist canopy

(B) to lock. Re-insert canopy mounting screw (Q) that was removed,

and then tighten both canopy mounting screws (Q) securely. Slide

canopy cover (U) up to canopy (B), aligning rounded part of slotted

holes in canopy cover (U) with screwheads in bottom of canopy (B).

Turn canopy cover (U) to the right (clockwise) until it stops. [Fig. 1]

6. Remove three screws from outer edge of switch housing plate (G).

Connect male plug from motor housing (D) to female plug from light

kit fitter (E). Make sure that they are securely connected. Attach light

kit fitter (E) to switch housing plate (G) with the three screws that

were removed. [Fig. 6]

FINAL INSTALLATION (continued from previous page)

Fig. 6

Fig. 7

7. Align dimples on socket cover with grooves in glass shade (J).

Turn glass shade (J) clockwise to secure. [Fig. 7] Repeat with the

other glass shades (J).

8. Install four candelabra base 40 watt bulbs (M) included. [Fig. 8]

Important: When replacing bulbs, allow bulb(s) and light kit to cool

before touching them.

Pull chain extensions (T) supplied in one of the hardware packs or

custom pull chain extensions (sold separately) may be attached to

fan and light pull chains. [Fig. 8]

NOTE: This fan is remote control adaptable (remote control sold

separately.)

FAN OPERATION

3. Use the fan reverse switch, located on the light kit fitter (E), to

optimize your fan for seasonal performance. [Fig. 3]

Note: Wait for fan to stop before moving the reverse switch.

3A. In warmer weather, counterclockwise movement of the

fan will result in downward airflow creating a wind chill

effect. [Fig. 3A]

3B. In cooler weather, clockwise movement of the fan will

result in upward airflow that can help move stagnant, hot air

off the ceiling area. [Fig. 3B]

IMPORTANT: Reverse switch must be set either completely to

the RIGHT or completely to the LEFT for fan to function. If the

reverse switch is set in the middle position [Fig. 3C], fan will not

operate.

1. The fan pull chain, labeled SPEED, has four positions to control

fan speed. One pull is HIGH, two is MEDIUM, three is LOW and

four turns the fan OFF. [Fig. 1]

2. Pull the light pull chain, labeled LIGHT, to turn the lights ON or

OFF. [Fig. 2]

Female

Plug Male

Plug

Socket

Cover

Socket

Fig. 8 M

Fig. 1

Fig. 2

Fig. 3

Fig. 3A Fig. 3B

Fig. 3C

CARE AND MAINTENANCE

At least twice each year, lower canopy (B) to check downrod (A) assembly, and then tighten all screws on the fan.

Clean motor housing (D) with only a soft brush or lint-free cloth to avoid scratching the finish. Clean blades (I) with a

lint-free cloth. You may occasionally apply a light coat of furniture polish to wood blades for added protection.

Important: Shut off main power supply before beginning any maintenance. Do not use water or a damp cloth to

clean the ceiling fan.

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Fan does not move. 1. Reverse switch not engaged. 1. Push switch firmly to the right or to the.

left.

2. Power is off or fuse is blown. 2. Turn power on or check fuse.

3. Faulty wire connection. 3. Turn power off. Loosen canopy (B) and

check all connections.

Noisy operation. 1. Blades (I) are loose. 1. Tighten all blade screws (L).

2. Cracked blade (I). 2. Replace blade (I).

3. Unapproved speed control. 3. Replace with an approved speed

control device.

Excessive wobbling. 1. Blades (I) are loose. 1. Tighten all blade screws (L).

2. Blade arms (H) incorrectly attached. 2. Re-install blade arms (H).

3. Unbalanced blades (I). 3. Switch with blade (I) from opposite

side.

4. Fan not securely mounted. 4. Turn power off. Carefully loosen

canopy (B) and verify that mounting

bracket (C) is secure.

5. Fan too close to vaulted ceiling. 5. Use a longer downrod (A) or move fan

to another location.

6. Set screw(s) on motor housing yoke 6. Tighten yoke set screw(s) securely.

is (are) not tightened properly.

7. Set screw on hanging ball is not 7. Carefully loosen and lower canopy (B)

tightened properly. and verify that set screw on hanging ball

is tightened securely.

Fan operates but lights fail. 1. Bulb(s) not installed correctly. 1. Re-install bulb(s).

2. Wires in canopy (B) not wired properly. 2. Check wires in canopy (B) and, if

necessary, re-wire according to

instructions on pages 6 and 7.

3. Wall switch to fan is off. 3. Make sure that wall switch to fan is on.

Lights dim when turning fan 1. Fan is lamped with more than 190W 1. No action necessary--fan will automati-

and/or lights on. and fan was turned off at wall switch, cally re-set within 5 seconds after turning

causing the wattage limiting device to wall switch back on.

re-set itself.

2. Fan is lamped with more than 190W 2. No action necessary--fan will automati-

causing the wattage limiting device in cally re-set within 5 seconds after turning

fan to re-set itself due to power outage. power back on.

Note: In order to avoid this problem, fan

may be lamped with bulbs totaling no

more than than 190W.

Lights appear dimmer than 1. Fan is lamped with more than 190W 1. Lamp light kit with bulbs that total no

they should. and wattage limiting device is reducing more than 190W.

the amount of wattage produced by the

light kit.

Warning: Before beginning work, shut off the power supply to avoid electrical shock.

Note: A small amount of "wobble" is normal and should not be considered a defect.

WARRANTY

LIMITED LIFETIME WARRANTY: Litex Industries warrants this fan to be free from defects in workmanship and

materials present at time of shipment from the factory for Lifetime limited from the date of purchase. This warranty

applies only to the original purchaser. Litex Industries agrees to correct any defect at no charge or, at our option,

replace the ceiling fan with a comparable or superior model.

To obtain warranty service, present a copy of your sales receipt as proof of purchase. All cost of removal and

reinstallation are the express responsibility of the purchaser. Any damage to the ceiling fan by accident, misuse or

improper installation, or by affixing accessories not produced by the manufacturer of this fan, are the purchaser's

own responsibility. Litex Industries assumes no responsibility whatsoever for fan installation during the limited

lifetime warranty. Any service performed by an unauthorized person will render the warranty invalid.

Due to varying climatic conditions, this warranty does not cover changes in brass finish, rusting, pitting, tarnishing,

corroding or peeling. Brass finish fans maintain their beauty when protected from varying weather conditions. Any

glass provided with this fan is not covered by the warranty.

Any replacement of defective parts for the ceiling fan must be reported within the first year from the date of

purchase. For the balance of the warranty, call our customer service department (at 1-800-527-1292) for return

authorization and shipping instructions so that we may repair or replace the ceiling fan. Any fan or parts returned

improperly packaged is/are the sole responsibility of the purchaser. There is no further express warranty. Litex

Industries disclaims any and all implied warranties. The duration of any implied warranty which cannot be

disclaimed is limited to the limited lifetime period as specified in our warranty. Litex Industries shall not be liable for

incidental, consequential or special damages arising at or in connection with product use or performance except as

may otherwise be accorded by law. This warranty gives you specific legal rights and you may also have other rights

which vary from state to state. This warranty supersedes all prior warranties.

10 Printed in China

TIEMPO

/VENTILADOR DE TECHO

ARTICULO #0125453

E192641

ADVERTENCIAS

• Lea y guarde estas instrucciones.

• Lea este instructivo detenida y completamente antes de tratar de ensamblar, instalar o hacer funcionar este

producto.

• Asegúrese de leer y entender la información de seguridad en la página 13 de estas instrucciones.

• No deseche la caja del ventilador ni la goma espuma incluida. Si hay que mandar el ventilador a la fábrica por

alguna reparación, se debe enviar en su paquete original para asegurar la protección apropiada contra daños que

podrían exceder la causa inicial por la cual se devolvió.

• PRECAUCION: Antes de proseguir, desconecte la electricidad, quitando los fusibles o cortando el suministro

de energía de los circuitos para evitar un choque eléctrico.

• ADVERTENCIA: Para reducir el riesgo de incendio o un choque eléctrico, no use este ventilador con

interruptor de velocidad variable.

• ADVERTENCIA: Para reducir el riesgo de incendio, choque eléctrico o lesión personal, no doble los brazos

de las paletas mientras las esté instalando, ni cuando esté balanceando las paletas ni cuando esté limpiando el

ventilador. No inserte objetos extraños entre las paletas giratorias del ventilador. Sujete a una caja de salida

marcada "Aceptable para sostener ventilador" ("ACCEPTABLE FOR FAN SUPPORT" en inglés) y use los tornillos

de montaje proporcionados con la caja de salida. La mayoría de las cajas de salida que se usan comúnmente para

sostener aparatos de alumbrado no son aceptables para sostener ventiladores y es posible que sea necesario

reemplazarla. Consulte con un electricista calificado si tiene alguna duda.

¿Preguntas, problemas, faltan piezas? Antes de regresar a la tienda, llame o póngase en contacto con

nuestro departamento de servicio al cliente al 1-800-527-1292, de 8:30 a.m. a 5:00 p.m., hora central, de lunes

a viernes. 11

El reglamento federal requiere que un ventilador de techo con juego de luz fabricado o

importado después del 1ro de enero del 2009 limite el vatiaje total que consume el juego

de luz a 190W. Por lo tanto, este ventilador tiene un aparato que sirve para limitar el

vatiaje. Si pone bombillas en el juego de luz de este ventilador que suman más de

190W, el aparato que sirve para limitar el vatiaje reducirá los vatios consumidos a

190W.

MODELO #E-TM52BNK5CS

Harbor Breeze® es marca registrada de

LF, LLC. Reservados todos los derechos.

TIEMPO

/VENTILADOR DE TECHO

ARTICULO #0125500

MODELO #E-TM52BNKB5CS

Harbor Breeze® es marca registrada de

LF, LLC. Reservados todos los derechos.

E192641

DEL

E-TM

marca

registrada

s marca registrada de

s todos los derechos.