Hatco Glo-Ray GRA-108 User guide

GLO-RAY®INFRARED FOODWARMER
APPLICATION INFORMATION
Hatco Glo-Ray®Infrared Foodwarmers are available in a variety of sizes and combinations to fit holding areas
of any length or depth. Some of the installation possibilities are described on this sheet. For more application
information contact your local Representative or the Hatco Corporation.
AVAILABLE SIZES
WIDTH: Aluminum Housing — 18"-12' (457-3,658 mm).Available in 6" (152 mm) increments –
single extrusion. Stainless Steel Housing — 24", 36", 48", 60", 72", and 96" (610, 914, 1219, 1524, 1829,
and 2438 mm) only.
DEPTH: Aluminum — 6" or 9" (152 or 229 mm) or combinations using 3" or 6" (76 or 152 mm)
spacers. Stainless Steel
— 6" (15 cm) only.
Incandescent lights are available for aluminum models only and can be ordered on either side of unit. Center
lights recommended for dual warmer mounting. The 60-watt incandescent shatter-resistant bulbs provide
illumination only and feature a special coating that guards against injury and food contamination in the event
of breakage.
MIN. 18" (457 mm)
(152 mm)
MAX. 144" (3,658 mm)

HEAT PATTERNS
PRE-FOCUSED: The Hatco Glo-Ray®radiating reflector directs infrared heat from the element
to the holding area recommended. Mounting heights vary depending on the type of heating element.
MOUNTINGARRANGEMENTS
BRACKETS: Standard hanger tabs are provided for undershelf, over shelf or chain installation.
An optional angle bracket allows vertical adjustment that fits 6" or 9" (152 or 229 mm) housings.
STANDS: A variety of optional stands are available for permanent and portable installation.
Available for both standard and high
wattage elements.
CAUTION:
Do not install Glo-Ray®warmers less than 10" (635 mm)
ABOVE NON-METALLIC SURFACE when using
standard wattage elements or 13" (330 mm) ABOVE NON-
METALLIC SURFACE with high wattage elements.
Dual warmers must be at least 30" (762 mm) ABOVE
NON-METALLIC SURFACES.
DO NOT INSTALL CLOSER THAN 3" (76 mm)
BETWEEN WARMERS.
18"-24"
(457-610 mm)
10"-16"
(254-406 mm)
Optional slant reflectors are available to direct
the heat pattern left or right.
2Form No. GRAB-0804

MOUNTINGARRANGEMENTS
ELECTRICAL DATA
UNDERSHELF: Hatco Glo-Ray®Foodwarmers must be mounted no
less than 1½" (38 mm) below the underside of a turned-downed shelf. If
the warmer is mounted flush to the undershelf, the heat build-up will
cause the wiring and switches to burn out – not covered under warranty.
The optional angle brackets are recommended for under-shelf installations.
A remote location for the control switches is recommended and required
for infinite switches.
PASS-THRU: If the pass-thru is 12" to 16"
(305-406 mm) wide, the standard wattage or high
wattage single unit can be used. For a 20" to 24"
(508-610 mm) wide pass-thru shelf, a dual unit
in either standard or high wattage is recommended.
Duals must always have a minimum spacing of
3" (76 mm) between warmers.
When mounting a Foodwarmer over a surface
other than stainless steel, consult the manufacturer
regarding surface temperature limits before
installing the warmer.
ELEMENTS:Available in standard or high
wattage, from 18" up to 8' (457 to 2438 mm)
in a single element. Glo-Ray models 108" through
144" (2743-3658 mm) contain tandem (end-to-end)
elements individually controlled. High temp wire
(90ºC minimum) must be used for power
connections.
SWITCHES: Glo-Ray Foodwarmers include
an on-off toggle switch as standard. Consult factory
on units with lights and dual warmers. Location
of switch or switches and power connection can
be specified, consult factory.
Infinite control is available to manually adjust heat
output. REMOTE INSTALLATION IS
RECOMMENDED. Glo-Ray is not moisture
proof. A reduction in life of switch may result if not
installed in a remote location.
REMOTE CONTROL ENCLOSURES:
Hatco Remote Control Enclosures are available for
use with Glo-Ray infrared foodwarmers. All models
are built in accordance with U.L. standards to
include switches, indicator lights, and wiring, and
are ready for installation. Available in four models:
RMB-3 (5 ½" (140 mm)), RMB-7 (9" (229 mm)),
RMB-14 (14" (356 mm)), and RMB-16
(16" (406 mm)).
Recommended for dual models or units with
infinite switches. Consult factory for type and
location of switches per enclosure.
VOLTAGE: Glo-Ray is available in 120, 208,
220, and 240 volts. Units with lights available in
120, 120/208 or 120/240, 220, or 240 volts. Models
GRA-18 and GRAH-18, 120 volts only. Consult
factory on units from 96" up to 144"
(2438-3658 mm) in width.
3 Form No. GRAB-0804

HATCO GLO-RAY®INFRARED FOODWARMERS
STANDARD WATT MODELS
ELECTRICAL RATINGS AND RECOMMENDATIONS
TANDEM ELEMENT MODELS
GRA-108 208 1850 8.9 YES — 2 required
GRA-108 240 1850 7.7 YES — 2 required
GRA-120 208 2100 10.1 YES — 2 required
GRA-120 240 2100 8.8 YES — 2 required
GRA-132 208 2320 11.2 YES — 2 required
GRA-132 240 2320 9.7 YES — 2 required
GRA-144 208 2550 12.3 YES — 2 required
GRA-144 240 2550 10.6 YES — 2 required
SINGLE ELEMENT MODELS INFINITE SWITCH
MODEL VOLTS WATTS TOTALAMPS AVAILABLE
GRA-18 120 250 2.1 YES
GRA-18 208 250 1.2 YES
GRA-18 240 250 1.0 YES
GRA-24 120 350 2.9 YES
GRA-24 208 350 1.7 YES
GRA-24 240 350 1.5 YES
GRA-30 120 450 3.8 YES
GRA-30 208 450 2.2 YES
GRA-30 240 450 1.9 YES
GRA-36 120 575 4.8 YES
GRA-36 208 575 2.8 YES
GRA-36 240 575 2.4 YES
GRA-42 120 675 5.6 YES
GRA-42 208 675 3.2 YES
GRA-42 240 675 2.8 YES
GRA-48 120 800 6.7 YES
GRA-48 208 800 3.8 YES
GRA-48 240 800 3.3 YES
GRA-54 120 925 7.7 YES
GRA-54 208 925 4.4 YES
GRA-54 240 925 3.9 YES
GRA-60 120 1050 8.8 YES
GRA-60 208 1050 5.0 YES
GRA-60 240 1050 4.4 YES
GRA-66 120 1160 9.7 YES†
GRA-66 208 1160 5.6 YES
GRA-66 240 1160 4.8 YES
GRA-72 120 1275 10.6 YES†
GRA-72 208 1275 6.1 YES
GRA-72 240 1275 5.3 YES
GRA-84 120 1500 12.5 YES†
GRA-84 208 1500 7.2 YES
GRA-84 240 1500 6.3 YES
GRA-96 120 1725 14.4 YES†
GRA-96 208 1725 8.3 YES
GRA-96 240 1725 7.2 YES
†Infinite switches available only with tandem elements, two switches required.
NOTE: Remote installation is recommended for infinite controls.
Consult factory for special applications.
4Form No. GRAB-0804

HATCO GLO-RAY®INFRARED FOODWARMERS
HIGH WATT MODELS
ELECTRICAL RATINGS AND RECOMMENDATIONS
†Infinite switches available only with tandem elements, two switches required.
NOTE: Remote installation is recommended for infinite controls.
Consult factory for special applications.
SINGLE ELEMENT MODELS INFINITE SWITCH
MODEL VOLTS WATTS TOTALAMPS AVAILABLE
GRAH-18 120 350 2.9 YES
GRAH-18 208 350 1.7 YES
GRAH-18 240 350 1.5 YES
GRAH-24 120 500 4.2 YES
GRAH-24 208 500 2.4 YES
GRAH-24 240 500 2.1 YES
GRAH-30 120 660 5.5 YES
GRAH-30 208 660 3.2 YES
GRAH-30 240 660 2.8 YES
GRAH-36 120 800 6.7 YES
GRAH-36 208 800 3.8 YES
GRAH-36 240 800 3.3 YES
GRAH-42 120 950 7.9 YES
GRAH-42 208 950 4.6 YES
GRAH-42 240 950 4.0 YES
GRAH-48 120 1100 9.2 YES
GRAH-48 208 1100 5.3 YES
GRAH-48 240 1100 4.6 YES
GRAH-54 120 1250 10.4 YES
GRAH-54 208 1250 6.0 YES
GRAH-54 240 1250 5.2 YES
GRAH-60 120 1400 11.7 YES
GRAH-60 208 1400 6.7 YES
GRAH-60 240 1400 5.8 YES
GRAH-66 120 1560 13.0 YES†
GRAH-66 208 1560 7.5 YES
GRAH-66 240 1560 6.5 YES
GRAH-72 120 1725 14.4 YES†
GRAH-72 208 1725 8.3 YES
GRAH-72 240 1725 7.2 YES
GRAH-84 120 2050 17.1 YES†
GRAH-84 208 2050 9.9 YES
GRAH-84 240 2050 8.5 YES
GRAH-96 120 2400 20.0 YES†
GRAH-96 208 2400 11.5 YES
GRAH-96 240 2400 10.0 YES
TANDEM ELEMENT MODELS
GRAH-108 208 2500 12.0 YES — 2 required
GRAH-108 240 2500 10.4 YES — 2 required
GRAH-120 208 2800 13.5 YES — 2 required
GRAH-120 240 2800 11.7 YES — 2 required
GRAH-132 208 3120 15.0 YES — 2 required
GRAH-132 240 3120 13.0 YES — 2 required
GRAH-144 208 3450 16.6 YES — 2 required
GRAH-144 240 3450 14.4 YES — 2 required
5 Form No. GRAB-0804

FOODWARMER APPLICATION WORKSHEET
GLO-RAY®INFRARED SPECIFICATIONS
Use diagram to assure proper specification of applicable unit
VOLTAGE (for heating elements)
■■120V ■■208V
■■220V ■■240V
WATTAGE
■■Standard ■■High Watt
(Consult factory for special wattages)
SWITCH(ES)
■■Toggle ■■Infinite
■■LIGHTS
(Lights will be 120V for US applications
and 220V or 240V for export aplications)
■■INDICATOR LIGHT
■■REMOTE CONTROL BOX
(Recommended for Dual models
and Infinite Switch)
■■CORD & PLUG
(120V – 72" (1829 mm) unit or less with C-Leg or
T-Leg stand only. Not available on Dual models.)
MOUNTING ARRANGEMENTS
■■C-Leg Stands* ■■T-Leg Stands*
■■Non-Adjustable Tubular Stands (Specify length)____________ ■■Other (Specify)____________
*Not available for Dual construction.
INSTALLATION DETAILS
Use diagram to assure proper specification of applicable unit
6Form No. GRAB-0804

NOTES
7 Form No. GRAB-0804

CANADA
FLANAGAN AGENCIES, INC.
Territory: Newfoundland, Nova
Scotia, New Brunswick, and Prince
Edward Island
Upper Coverdale, NB
506/387-8757
FAX Number: 506/387-8750
HAMILTON AGENCIES
Territory: Quebec
Lachine, Quebec 514/639-4433
FAX Number: 514/639-4431
COLLIS-NUNES GROUP, INC.
Territory: Ontario
Concord, Ontario 905/660-4600
FAX Number: 905/660-4606
DENNIS BRAUN AGENCY
Territory: Saskatchewan and
Manitoba Territory
Winnipeg, Manitoba204/663-8077
FAX Number: 204/663-8109
ADAMOSKI GROUP, INC.
Territory: Alberta
Calgary, Alberta 403/217-0800
FAX Number: 403/217-0818
DENNETT ENTERPRISES LTD.
Territory: British Columbia, the Yukon
Territory
Burnaby, B.C. 604/415-6400
FAX Number: 604/415-6440
HATCO CORPORATION
P.O. Box 340500, Milwaukee, WI 53234-0500 U.S.A.
[phone] [phone]
Fax [phone] [phone]
email: [email protected]
HATCO SALES REPRESENTATIVES
Printed in U.S.A. August 2004
U.S.A.
C.R. PETERSON ASSOCIATES
Territory: CT, ME, MA, NH, RI & VT
Portland, ME 207/899-2068
FAX Number: 207/899-2068
Easton, MA 508/238-8821
FAX Number: 508/238-3647
QUALITY REP SOURCE
Territory: NY State excluding
Westchester County and Long Island
Burnt Hills, NY 518/399-6040
FAX Number: 518/399-6039
Victor, NY 585/924-9440
FAX Number: 585/924-1445
PECINKA-FERRI ASSOC., INC.
Territory: Fairfield county in CT, N.
NJ & Westchester and Long Island
counties in NY
Little Falls, NJ 973/812-4277
FAX Number: 973/812-4284
Mineola, NY 516/742-2113
FAX Number: 516/742-2337
SCHMID-DEWLAND ASSOCIATES
Territory: DE, S. NJ & E. PA
Gibbsboro, NJ 856/783-3400
FAX Number: 856/783-7375
Wescosville, PA 610/395-8700
FAX Number: 610/395-1458
SCHMID WILSON GROUP, INC.
Territory: MD, VA, Washington DC &
Morgan, Berkley & Jefferson counties
in WV
Owings Mills, MD 410/998-9191
FAX Number: 410/998-9195
Alexandria, VA 703/706-8147
FAX Number: 703/706-8150
GRIFFIN MARKETING GROUP, INC.
Territory: NC & SC
Clayton, NC 919/553-2693
FAX Number: 919/553-5226
Greensboro, NC 336/282-5800
FAX Number: 336/282-1050
Salisbury, NC 704/797-8068
FAX Number: 704/797-8069
Irmo, SC 803/407-7373
FAX Number: 803/407-7395
BILL MCCOY ASSOCIATES
Territory: GA
Atlanta, GA 770/455-6137
FAX Number: 770/457-3685
TEPPER & ASSOCIATES, INC.
Territory: FL
Miami, FL 305/551-5000
FAX Number: 305/551-8711
Aventura, FL 305/935-9395
FAX Number: 305/935-9396
Ponte Vedra Beach, FL
904/280-0279
FAX Number: 904/280-0281
St. Petersburg, FL 727/322-1212
FAX Number: 727/322-1313
Form No. GRAB-0804
DANIEL C. GREEN AGENCY
Territory: W. PA & WV excluding
Morgan, Berkley & Jefferson counties
Pittsburgh, PA 412/364-6094
FAX Number: 412/364-4532
THE HGA GROUP, INC.
Territory: IN excluding Lake & Porter
counties & Lower MI
Fischers, IN 317/595-9788
FAX Number: 317/595-9470
Mt. Pleasant, MI 517/773-1764
FAX Number: 517/773-8347
Plymouth, MI 734/453-5060
FAX Number: 734/453-5818
BAUER MARKETING GROUP
Territory: KY & OH
Akron, OH 330/865-6709
FAX Number: 330/865-6716
Cincinnati, OH 513/281-4600
FAX Number: 513/281-4603
THE WALLIN GROUP. INC.
Territory: AL, AR, LA, MS, & TN
Pelham, AL 205/621-8122
FAX Number: 205/621-8263
Little Rock, AR 501/663-2438
FAX Number: 501/663-2439
Harahan, LA 504/733-3344
FAX Number: 504/733-0854
Brandon, MS 601/992-7260
FAX Number 601/992-7350
Brentwood, TN 615/370-1311
FAX Number: 615/370-1317
Knoxville, TN 865/470-4901
FAX Number: 865/470-4995
Memphis, TN 901/370-4724
FAX Number 901/370-4734
THE JAYMARK GROUP, LTD.
Territory: Northern IL & Lake and
Porter counties in IN
Elk Grove Village, IL847/545-1918
FAX Number: 847/545-1932
MELVILLE MARKETING GROUP
Territory: MN, ND, SD & W. WI
Minneapolis, MN 612/338-5078
FAX Number: 612/338-5505
MIDWEST PROFESSIONAL REPS
Territory: S. IL, IA, KS, MO & NE
Iowa City, IA 319/338-2712
FAX Number: 319/338-3752
Overland Park, KS 913/677-4994
FAX Number: 913/677-2883
Eureka, MO 636/938-5575
FAX Number: 636/938-7165
MUNN MARKETING GROUP
Territory: OK & TX excluding El Paso
Shawnee, OK 405/395-9710
FAX Number 405/395-9709
Addison, TX 972/732-0057
FAX Number: 972/248-2161
Austin, TX 512/828-0510
FAX: [phone]
Houston, TX 281/557-7909
FAX: [phone]
JOHNSON, PIKE & ASSOCIATES
Territory: CO, MT, NM, El Paso in TX,
UT & WY
Chandler, AZ 480/899-1826
FAX: [phone]
Denver, CO 303/572-0084
FAX Number: 303/572-8152
West Jordan, UT 801/260-1840
FAX Number: 801/260-1935
PROFESSIONAL REPS
OF ARIZONA, INC.
Territory: AZ
Phoenix, AZ 602/995-8922
FAX Number: 602/864-1754
ENGLISH NORTHWEST
MARKETING, INC.
Territory: AK, ID, OR & WA
Portland, OR 503/254-7303
FAX Number: 503/253-4038
Seattle, WA 206/525-3856
FAX Number: 206/523-7095
PREMIER MARKETING GROUP,
INC.
Territory: N. CA & NV excluding
Lincoln and Clark Counties
Sacramento, CA 916/361-9500
FAX Number: 916/361-4500
THE FISCHER GROUP
Territory: S. CA & Lincoln and Clark
counties in NV
Orange, CA 714/921-2660
FAX Number: 714/921-2544
Temecula, CA 714/921-2660
FAX Number: 909/303-9064
Henderson, NV 714/921-2660
FAX Number 702/897-1239
PACIFIC RIM REP GROUP, INC.
Territory: HI
Aiea, HI 808/487-7377
FAX Number: 808/485-2711
CLARK, MALONE & ASSOCIATES
Territory: Upper MI & E. WI
New Berlin, WI 262/796-8661
FAX Number: 262/796-8662