Hayward OmniLogic HTG-OL150c Administrator Guide

OmniLogic®
How To Guide
HTG-OL150c Copyright 2016 Hayward Industries Inc.

How To: Back-Up Configuration
2
Use the steps provided to backup a configuration. These steps aid firmware upgrades,
MSP changes, and corrupted configurations.
On the right of the dashboard locate and tap
the “config” icon.
Select the “backup config” option (third down
on the left most column).
Select “Backup to USB”, after inserting a USB
drive, then press the check mark.
Once the backup is confirmed press the check
mark to finalize.
Step 4
Step 2
Step 3
Step 1

3
Use these steps to load a previously saved configuration:
NOTE: If restoring the configuration from a USB drive, plug-in the drive prior
to starting this process.
On the right of the dashboard locate and tap
the “config” icon.
Select the “restore config” option (fourth
down on the left most column).
Select where the file is stored, in this case
“Restore from USB”.
Select the desired file to restore with the .bak
file extension and press the check to finalize.
Step 4
Step 2
Step 3
Step 1
How To: Restore a Configuration

How To: Download Config. from Web
4
Use the steps provided to download a configuration file from the Web.
Log into the registered web account via:
www.haywardomnilogic.com
On the top right, select profile>msp
configuration.
Select “Download”. Soon after, the file should
appear on the hard drive (typically under the
download folder).
Verify the file has the .xml file extension.
Note: the file may be renamed as long as the
.xml is not changed or removed.
Step 1 Step 2
Step 3 Step 4

How To: Download Config. from Web (cont.)
5
Once config. is copied AND USB is ejected, go to the next section to load web config.
Right click on the downloaded file and copy it. Insert USB drive into the PC & launch folder.
Paste downloaded file onto the USB drive,
waiting for the copying process to completely
finish.
IMPORTANT: Next, safely remove the USB by
right clicking on the application & selecting
“Eject”.
Step 5 Step 6
Step 7 Step 8

6
Use these steps to load a Configuration that has been downloaded from the web.
NOTE: Plug-in the USB drive prior to starting this process.
On the right of the dashboard locate and tap
the “config” icon.
Select the “restore config” option (fourth
down on the left most column).
Select where the file is stored, because this file
was loaded from the web onto a USB drive,
select “Restore from USB”.
Select downloaded file, if unchanged, it should
show as “MspConfiguration.xml”. Press the
check to finalize.
Step 4
Step 2
Step 3
Step 1
How To: Load a Config. Downloaded from Web

How To: Download Firmware
7
To download the latest firmware to a USB drive go to www.hayward.com
Support Center> Automation > OmniLogic > Firmware Updates
Step 1: Right click on the link of the file
you wish to download.
Step 2: Within the options menu select
"Save link as..."
(Note: USB drive must already be
connected to your computer).
Step 3: From the "Save As" window
navigate to the desired USB drive.
(Note: please make sure to select the
root directory of the USB drive).
Step 4: Before saving, change the
“Save as type” to “All Files” AND
remove the “.txt” file extension that
automatically appears. Then click on
"Save" button.
(Note: failing to remove the .txt file
extension will result in an unreadable
firmware upgrade file).
Step 4
Step 1-3
This process was accomplished through Google’s Chrome Browser.

Tap device to upgrade then check mark.Tap the “Upgrade” icon.
How To: Upgrade Firmware
8
Press the power button. Select “service mode”.
Step 4
Step 2
Step 3
Step 1
Insert the USB drive into the side of the MSP and follow the steps provided below:

How To: Upgrade Firmware (cont.)
9
Select storage method (USB). Select latest file (downloaded from web).
Press check mark to start the upgrade process
(DO NOT power off while in process).
Press check mark when complete (100%),
system will reboot.
Step 8
Step 6
Step 7
Step 5
NOTE: Make sure all devices are up to the latest firmware revision.

Tap anywhere on the screen to advance past
the warning screen.
Locate and tap on “EraseCalib”. This will
prompt a question screen.
How To: Clear MSP Calibration
10
On the right of the dashboard locate and tap
the “config” icon.
Step 4
Step 2
Step 3
Use the steps provided to clear the MSP calibration file. This process is recommended
if icon or text box selection is difficult.
Once in config, press the right arrow once and
select the “shell command” option.
Step 1