HEALTH RIDER HREL50020 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. HREL50020
Serial No.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE. The
technicians on our customer hot
line will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Visit our website at
www.healthrider.com
new products, prizes,
fitness tips, and much more!
USER’S MANUAL

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL CROSSTRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
2
HealthRider is a registered trademark of ICON Health & Fitness, Inc.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical crosstrainer.
1. Read all instructions in this manual before
using the elliptical crosstrainer.
2. It is the responsibility of the owner to ensure
that all users of the elliptical crosstrainer
are adequately informed of all precautions.
3. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrain-
er indoors, away from moisture and dust.
4. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
5. Keep children under age 12 and pets away
from the elliptical crosstrainer at all times.
6. The elliptical crosstrainer should not be used
by persons weighing more than 250 pounds.
7. Always hold the handlebars, the pulse han-
dlebar, or the upper body arms when mount-
ing, dismounting, or using the elliptical
crosstrainer.
8. Wear appropriate exercise clothing when
using the elliptical crosstrainer. Always wear
athletic shoes for foot protection.
9. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
10. When you stop exercising, allow the pedals
to slowly come to a stop.
11. Keep your back straight when using the ellip-
tical crosstrainer; do not arch your back.
12. If you feel pain or dizziness at any time
while exercising, stop immediately and
begin cooling down.
13. The elliptical crosstrainer is intended for
in-home use only. Do not use the elliptical
crosstrainer in a commercial, rental, or insti-
tutional setting.
14. The decal shown below has been placed on
the elliptical crosstrainer. If the decal is
missing or illegible, please call our Customer
Service Department toll-free at 1-800-999-
3756 to order a free replacement decal.
Apply the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

4
BEFORE YOU BEGIN
Congratulations for selecting the new HealthRider®
E55 elliptical crosstrainer. The HealthRider®E55 ellip-
tical crosstrainer is an incredibly smooth exerciser that
moves your feet in a natural elliptical path, minimizing
the impact on your knees and ankles. And the unique
HealthRider®E55 features adjustable resistance and
incline to help you get the most from your exercise.
Welcome to a whole new world of natural, elliptical-
motion exercise from HealthRider.
For your benefit, read this manual carefully before
you use the elliptical crosstrainer. If you have
questions after reading this manual, please call our
Customer Service Department toll-free at 1-800-999-
3756, Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time (excluding holidays). Please note the
product model number and serial number before call-
ing. The model number is HREL50020. The serial
number can be found on a decal attached to the ellip-
tical crosstrainer (see the front cover of this manual
for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Pulse Handlebar
Handlebar
Upper Body Arm
FRONT
BACK RIGHT SIDE
Pedal Arm
Pedal Disk
Wheel
Pedal
Console
Bookrack
Incline Ramp
Pedal Knob

5
ASSEMBLY
Assembly requires two people. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included allen wrenches, assembly requires a phillips screwdriver , an adjustable
wrench , and a rubber mallet .
As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on
page 22. The second number refers to the quantity used in assembly. Note: Some small parts may have been
pre-assembled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.
M10 x 105mm Carriage Bolt (60)–2
3/4” Axle Cap (61)–2
57mm Spacer (22)–2
M10 Nylon
Locknut (26)–4
M8 x 19mm
Screw (30)–4
M8 Split
Washer (58)–4
M4 x 16mm
Screw (72)–1
M10 x 65mm Carriage Bolt (43)–2
M10 x 92mm Carriage Bolt (86)–2
M8 Nylon
Locknut (80)–8
M10 Split
Washer (13)–3
M10 x 25mm
Screw (100)–3
M8 Washer
(33)–6 M10 Washer
(94)–2 Plastic Pedal
Spacer (11)–2
M8 x 40mm Button
Bolt (101)–6
Console
Screw (35)–4

6
1. Identify the Rear Stabilizer (59), which has Wheels (45)
attached to it.
Attach the Rear Stabilizer (59) to the rear of the Frame
(1) with the two M10 x 105mm Carriage Bolts (60) and
two M10 Nylon Locknuts (26). Make sure that the
Rear Stabilizer is turned so the Wheels (45) are not
touching the floor.
26
1
60
45
26 59
1
2. Attach the Front Stabilizer (14) to the front of the
Frame (1) with the two M10 x 92mm Carriage Bolts
(86) and two M10 Nylon Locknuts (26).
4. Slide an M8 Split Washer (58) and an M8 Washer (33)
onto an M8 x 19mm Screw (30). Tighten the Screw into
one end of the other Incline Axle (29). Apply a small
amount of grease to the Incline Axle.
Lift the Incline Ramp (5). Insert the Incline Axle (29)
through one side of the Incline Ramp, through a 57mm
Spacer (22), through the motor screw, through another
57mm Spacer (22), and then through the other side of
the Incline Ramp.
Slide an M8 Split Washer (58) and an M8 Washer (33)
onto an M8 x 19mm Screw (30). Tighten the Screw into
the open end of the Incline Axle (29).
86 14
26
26
1
2
3
5
V-shaped Groove
29
Grease
33
33
30
30
58
58
1
Tubes
Tubes
3. Slide an M8 Split Washer (58) and an M8 Washer (33)
onto an M8 x 19mm Screw (30). Tighten the Screw
into one end of an Incline Axle (29). Apply a small
amount of the included grease to the Incline Axle.
Align the indicated tubes on the Incline Ramp (5) with
the tubes on the Frame (1). Make sure that the
Incline Ramp is turned so the V-shaped grooves
are on top. Insert the Incline Axle (29) into the Incline
Ramp and the Frame. Note: It may be helpful to tap
the Incline Axle with a rubber mallet to insert it.
Slide an M8 Split Washer (58) and an M8 Washer (33)
onto an M8 x 19mm Screw (30). Tighten the Screw
into the open end of the Incline Axle (29).
5
29
30
30
58
58
33
33
Grease
22
Motor
Screw
4

7. Apply grease to the welded bolt on the Left Pedal Arm
(3). Slide a Chrome Tube (98) and an M8 Washer (33)
onto the welded bolt. Make sure that the Chrome
Tube is turned exactly as shown in the inset draw-
ing. Tighten an M8 Nylon Locknut (80) onto the welded
bolt.
Attach the other Chrome Tube (not shown) to the Right
Pedal Arm (4) in the same way.
Apply a small amount of the included Teflon®lubricant
to a paper towel. Rub a thin layer of the lubricant onto
both Chrome Tubes (98).
98
33
33
Wide
Side
Narrow
Side
80
80
3
3
Grease
Lubricate
98
7
5. Identify the Left Pedal Arm (3), which has an “L” stick-
er attached to it. Identify the Left Pedal (41), which
has the letter “L” molded onto the bottom.
Insert an M10 x 65mm Carriage Bolt (43) into the cen-
ter of the slot in the Left Pedal (41) and through the
Left Pedal Arm (3). Slide an M10 Washer (94) onto the
Carriage Bolt and then tighten a Pedal Knob (103)
onto it.
Attach the Right Pedal (not shown) to the Right Pedal
Arm (not shown) in the same way.
543
3
41
Center Position
94
103
Open Side
6. Apply a small amount of grease to the axle on the left
Crank Arm (6).
Slide a Plastic Pedal Spacer (11) and the Left Pedal
Arm (3) onto the axle on the left Crank Arm (6). (Note:
It may be helpful to use a rubber mallet to tap these
parts on. Do not to confuse the Left Pedal Arm with
the Right Pedal Arm [not shown]; look at the posi-
tion of the round tube to identify the Left Pedal
Arm.) Tap a 3/4” Axle Cap (61) onto the axle.
Attach the Right Pedal Arm (not shown) in the same way.
6
Grease
11
61
3
6
Round
Tube
7
2
Console
Wires Ground
Wire
99
35 35
102
87
72
8. Remove the four Console Screws (35) from the
Console (87). Connect the Extension Harness (99)
and the Pulse Wires (102) to the corresponding con-
sole wires. The orange and black Pulse Wire
should be connected to the console wire marked
with an “R.”
Attach the ground wire to the Upright (2) with an M4 x
16mm Screw (72).
Insert all of the extra wiring into the Upright (2). Attach
the Console (87) to the Upright with the four Console
Screws (35) that you removed from the Console. Be
careful to avoid pinching the wires.
8
Make sure the
ground wire,
console wires,
and Wires (99,
102) do not get
pinched and
damaged during
this step.
Welded Bolt

8
12. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware
may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat
under the elliptical crosstrainer.
10. Slide the Left Upper Body Arm (15), which is marked
with an “L” sticker, onto the Chrome Tube (98) on the
Left Pedal Arm (not shown). Slide the Right Upper
Body Arm (18) onto the Chrome Tube on the Right
Pedal Arm (4). Make sure that the Upper Body Arms
are on the correct sides—the upper ends will bend
in the direction shown by the arrows. Next, slide an
Axle Cover (49) onto the post on each Upper Body
Arm.
Apply grease to the Arm Axle (34). Insert the Arm Axle
into the Upright (2), the right Pivot Cover (49), and the
Right Upper Body Arm (18) as shown. Push the Arm
Axle into the Upright until the left end of the Arm Axle is
flush with the left side of the Upright. Next, raise the
Left Upper Body Arm (15) and insert the Arm Axle into
the left Axle Cover (49) and the Left Upper Body Arm.
Center the Arm Axle.
10
11
2
49
49
Post
Post
Grease
34
34
51
80
80
101
105
101
104
15
15
18
11. Push an Axle Cap (51) onto the left Axle Cover (49).
Orient the Left Handlebar (104) as shown. Slide the
Left Handlebar onto the indicated post and the Arm
Axle (34). Attach the Left Handlebar with three M8 x
40mm Button Bolts (101) and three M8 Nylon Locknuts
(80).
Attach the Right Handlebar (105) in the same way.
98
98
4
9. While another person holds the Upright (2) near the
Frame (1), connect the Wire Harness (25) to the
Extension Harness (99). Attach the Upright to the
Frame with three M10 x 25mm Screws (100) and three
M10 Split Washers (13). Be careful to avoid pinching
the Wire Harnesses.
9
2
13
13
13
99
100
1
100
25
Make sure the
Wire Harnesses
(25, 99) do not
get pinched and
damaged during
this step.

9
HOW TO USE THE ELLIPTICAL CROSSTRAINER
PLUGGING IN THE POWER CORD
Locate the power cord on the elliptical crosstrainer.
Plug the power cord into a surge protector (not includ-
ed), and plug the surge protector into a 120-volt outlet.
The displays and various indicators on the console will
light and a tone will sound. To decrease the possibil-
ity of damaging the elliptical crosstrainer, always
use a surge protector.
Note: When the power cord is plugged in, the
incline ramp will move to the lowest position. In
addition, the incline ramp may rise and then move
back to the lowest position as the elliptical
crosstrainer performs a calibration routine. During
the routine, the letters “CAL” will appear in the
right LED display and then dashes will appear in
the left LED display.
EXERCISING ON THE ELLIPTICAL CROSSTRAINER
To mount the elliptical crosstrainer, hold the handlebars
or the pulse handlebar and step onto the pedal that is
in the lowest position. Next, step onto the other pedal.
Push the pedals until they begin to move with a contin-
uous motion.
Note: The pedal disks can turn in either direction.
It is recommended that you move the pedal disks
in the direction shown by the arrow above; howev-
er, to give variety to your exercise, you may turn
the pedal disks in the opposite direction.
To dismount the elliptical crosstrainer, wait until the
pedals come to a complete stop. Note: The elliptical
crosstrainer does not have a free wheel; the ped-
als will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
USING THE UPPER BODY ARMS
The upper body arms are
designed to add upper-
body exercise to your
workouts. Move the
upper-body arms forward
and back as you exercise
in order to work your
arms, back, and shoul-
ders.
To exercise only your
lower body, hold the han-
dlebars or the pulse han-
dlebar as you exercise.
ADJUSTING THE PEDALS
The pedals can be adjusted to any of five positions. To
adjust the pedals, loosen the pedal knobs beneath the
pedals, slide the pedals forward or backward, and then
retighten the pedal knobs.
CAUTION: Before operating the
console, read the following precautions.
• Always hold the pulse handlebar or the upper
body arms when mounting, dismounting, or
using the elliptical crosstrainer.
• When you stop exercising, allow the pedals to
slowly come to a stop.
• Keep your feet and objects from beneath the
elliptical crosstrainer.
• To reduce the risk of electric shock, keep the
console dry.
• The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
Pedals
Pedal Disk
Pulse Handlebar
Handlebar
Upper Body
Arms

10
DESCRIPTION OF THE CONSOLE
The advanced console offers a variety of features to
help you get the most from your workouts.
When the manual mode of the console is selected, the
incline and the resistance of the elliptical crosstrainer
can be changed with a touch of a button. As you exer-
cise, the LED matrix and displays will provide continu-
ous exercise feedback. You can even measure your
heart rate using the built-in pulse sensor.
The console also offers eight certified personal trainer
programs. Each program automatically changes the
incline and the resistance of the elliptical crosstrainer
as it guides you through an effective workout.
The console also features new iFIT.com interactive
technology. IFIT.com technology is like having a per-
sonal trainer right in your home. Using a stereo audio
cable (available at electronics stores), you can connect
the elliptical crosstrainer to your home stereo, portable
stereo, or computer and play special iFIT.com CD pro-
grams (CD’s are available separately). IFIT.com CD
programs automatically control the incline and the
resistance of the elliptical crosstrainer as a personal
trainer coaches you through every step of your work-
out. High-energy music provides added motivation.
Each CD features two programs designed by certified
personal trainers.
In addition, you can connect the elliptical crosstrainer
to your VCR and TV and play iFIT.com video programs
(videocassettes are available separately). Video pro-
grams offer the same benefits as iFIT.com CD pro-
grams, but add the excitement of working out with a
class and an instructor.
With the elliptical crosstrainer connected to your com-
puter, you can also go to our new Web site at
www.iFIT.com and access audio programs and video
programs directly from the internet.
To purchase iFIT.com CD’s and videocassettes,
call toll-free 1-800-735-0768.
A
E
FG
B
IK
J
B
L
CONSOLE DIAGRAM
C
D
H

11
Refer to the drawing on page 10.
Note: If there is a thin sheet of clear plastic on the
face of the console, remove it.
A. Incline display—This display shows the incline level
of the elliptical crosstrainer.
B. Program profiles—These profiles show how the
resistance and incline of the elliptical crosstrainer
will change during personal trainer programs. For
example, the upper profile on the right side of the
console shows that the resistance and incline will
gradually increase during the first half of the indi-
cated program, and then gradually decrease during
the last half.
C. MANUAL CONTROL indicator—This indicator will
light to show when the manual mode is selected.
D. Program/iFIT.com indicators—These indicators light
to show when a personal trainer program or the
iFIT.com mode is selected.
E. LED matrix—When the manual mode or the
iFIT.com mode is selected, the LED matrix will
show a quarter-mile track. When a personal trainer
program is selected, the matrix will show your
progress and upcoming resistance settings.
F. TIME/DISTANCE/INCLINE/LAPS display—This dis-
play shows the elapsed time (or the remaining time
in a personal trainer program), the distance that the
pedals have moved, the incline level, and the total
number of quarter-mile laps completed. The display
will change modes every few seconds. Note: The
letter “L” will appear in the display when the number
of laps is shown.
G. SPEED/CALORIES/PULSE/RESISTANCE display—
This display shows your current speed, the approx-
imate number of calories you have burned, and the
resistance level. The display will change modes
every few seconds. When the pulse sensor is
used, the display will also show your heart rate.
H. PROGRAM SELECT button—This button is used
to select the manual mode, personal trainer pro-
grams, and the iFIT.com mode.
I. RAMP buttons—These buttons control the incline
of the elliptical crosstrainer. Each time one of the
buttons is pressed, the incline level will change by
1%. If a button is held down, the incline will change
in increments of 5%. The incline range is 0% to
30%.
J. START/PAUSE button—This button is used to start
the console and to pause the console. If the button
is held down, the displays will be reset.
K. RESISTANCE buttons—These buttons control the
resistance of the elliptical crosstrainer. There are
ten resistance levels.
L. RESISTANCE display—This display shows the
resistance level of the elliptical crosstrainer.

12
Turn on the power
Make sure that the power cord is properly plugged
in (see page 9). To turn on the power, press the
START/PAUSE button or begin exercising. The
console will sound a tone and various displays
and indicators will light. Note: If you have moved
the pedals, the power will already be on.
Select the manual mode
Each time the power is
turned on, the manual
mode will be selected
and the MANUAL CON-
TROL indicator will light.
If a personal trainer pro-
gram or the iFIT.com mode has been selected,
press the PROGRAM SELECT button repeatedly
to select the manual mode. Note: When you
press the PROGRAM SELECT button, the
incline will automatically change to the lowest
position.
Begin exercising and adjust the incline and
the resistance of the elliptical crosstrainer
As you exercise, adjust the incline and resistance
as desired by pressing the RAMP and RESIS-
TANCE buttons. The incline setting will be shown
in the left display. The resistance setting will be
shown in the right display. Note: After the buttons
are pressed, it may take a few seconds for the
selected setting to be reached.
Follow your progress with the displays
When the manual mode is selected, the LED
matrix will display a quarter-mile track. As you
exercise, the indicators around the track will light
in sequence until you have completed one lap.
The LED matrix will then darken and a new lap
will begin.
The left display will show the elapsed time, the
distance that the pedals have moved, the incline
level, and the number of laps you have completed.
The right display will show your current speed,
the approximate number of calories you have
burned, and the resistance level. The right display
will also show your heart rate when the pulse sen-
sor is used (see step 5).
Note: The console can display speed and distance
in either miles or kilometers. To find which unit of
measurement is selected, press the RAMP +
button and the
RESISTANCE +
button simultane-
ously for a few
seconds. The LED
matrix will show a
letter E for English
miles or a letter M
for metric kilome-
ters. Press the
RESISTANCE +button to change the unit of
measurement if desired. When the desired unit of
measurement is selected, press the right side of
the START/PAUSE button.
Measure your heart rate if desired
Important: If
there are thin
sheets of plastic
on the metal con-
tacts on the pulse
sensor, peel off
the plastic before
using the pulse
sensor. To use the
pulse sensor, place your hands on the metal con-
tacts. Your palms must be resting on the upper
contacts and your fingers must be touching the
lower contacts. Avoid moving your hands. When
your pulse is detected, the heart-shaped indicator
below the right display will light, one or two dash-
es (– –) will appear, and then your heart rate will
be shown.
For the most accurate heart rate reading, continue
to hold the contacts for about 15 seconds. The
right display will show your heart rate for up to 15
seconds; the display will then show your current
speed, calories burned, your heart rate, and the
resistance level, in seven-second intervals. Note:
Your heart rate will be shown only when the
pulse sensor is used.
When you are finished exercising, the console
will automatically turn off
If the pedals are not moved and the console but-
tons are not pressed for a few minutes, the con-
sole will automatically switch into a “sleep”
mode. Important: Unplug the power cord after
each use.
6
5
4
3
2
1
HOW TO USE THE MANUAL MODE
Metal
Contacts

13
Turn on the power
See step 1 on page 12.
Select one of the eight personal trainer
programs
Each time the
power is turned on,
the manual mode
will be selected. To
select a personal
trainer program,
press the PRO-
GRAM SELECT
button repeatedly until one of the eight program
indicators lights. Note: When you press the PRO-
GRAM SELECT button, the incline will automati-
cally change to its lowest position.
As you select each program, the LED matrix will
show the first eight resistance settings of the pro-
gram you have selected (see step 3).
Start the program
To start the program, press the START/PAUSE
button or simply begin exercising.
Each program is divided into 20 one-minute seg-
ments. One resistance setting and one incline
setting are programmed for each segment. The
resistance setting
for the first seg-
ment is shown in
the flashing CUR-
RENT PROGRAM
SEGMENT col-
umn of the LED
matrix. The set-
tings for the next
seven segments
are shown in the columns to the right. (The incline
settings are not shown in the matrix.)
When only three seconds remain in the first seg-
ment, a series of tones will sound. All resistance
settings will then move one column to the left.
The setting for the second segment will then be
shown in the CURRENT PROGRAM SEGMENT
column and the elliptical crosstrainer will adjust to
the second resistance and incline settings.
If the resistance or incline setting for the current
segment is too high or too low, the setting can be
adjusted by pressing the RESISTANCE or RAMP
buttons. However, when the next segment begins,
the elliptical crosstrainer will automatically adjust
to the next resistance and incline settings for the
program.
The program will continue until the setting for the
twentieth segment is shown in the CURRENT
PROGRAM SEGMENT column and the left dis-
play counts down to zero. The console will then
sound a tone and the two displays will pause. The
console will remain in this state until the START/
PAUSE button or the PROGRAM SELECT button
is pressed.
To pause the program before it is completed,
press the START/PAUSE button or allow the ped-
als to come to a stop and step off the pedals. A
tone will sound, the two displays will pause, and
the left display will flash. To restart the program,
simply resume exercising. Note: The console will
automatically switch into the sleep mode if the
pedals are not moved for a few minutes.
Follow your progress with the console displays
As you exercise, the two displays will show the
time remaining in the program, the distance that
the pedals have moved, the incline level, the
number of laps completed, your current speed,
the approximate number of calories burned, and
the resistance level. Your heart rate will also be
shown when the pulse sensor is used (see step 5
on page 12).
Measure your heart rate if desired
See step 5 on page 12.
When you are finished exercising, the console
will automatically turn off
See step 6 on page 12.
6
5
4
3
2
1
HOW TO USE CERTIFIED PERSONAL TRAINER
PROGRAMS

14
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER
To use iFIT.com CD’s, the elliptical crosstrainer must
be connected to your portable CD player, portable
stereo, home stereo, or computer with CD player. See
pages 14 to 15 for connecting instructions. To use
iFIT.com videocassettes, the elliptical crosstrainer
must be connected to your VCR. See page 16 for con-
necting instructions. To use iFIT.com programs
directly from our Web site, the elliptical crosstrainer
must be connected to your home computer. See page
15 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT
and PHONES jacks, see instruction A below. If
your CD player has only one jack, see instruction B.
A. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your CD player.
Plug your headphones into the PHONES jack.
B. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your CD player. Plug your headphones into the
other side of the Y-adapter.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1/8” LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the AUDIO OUT jack on your stereo.
B. Refer to the drawing above. Plug one end of a 1/8”
to 1/8” stereo audio cable (available at electronics
stores) into the jack beneath the console. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
C. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the
other side of the Y-adapter.
LINE OUT
PHONES LINE OUT
PHONES
Audio
Cable
Head-
phones
A
AUDIO OUT
RIGHT
LEFT
LINE OUT
Audio
Cable
A, B
PHONES
Audio
Cable
C
PHONES
PHONES
Audio
Cable
1/8”
Y-adapter
Headphones
B
1/8”
Y-adapter
Headphones

15
HOW TO CONNECT YOUR HOME STEREO
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your stereo.
B. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack beneath
the console. Plug the other end of the cable into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the LINE OUT jack on your stereo and plug the wire
into the unused side of the Y-adapter. Plug the Y-
adapter into the LINE OUT jack on your stereo.
HOW TO CONNECT YOUR COMPUTER
Note: If your computer has a 1/8” LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
B. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speak-
ers into the other side of the Y-adapter.
CD
VCR
Amp
LINE OUT
LINE OUT
Audio
Cable
A
LINE OUT
Audio
Cable
A
CD
VCR
Amp
LINE OUT
Audio
Cable
RCA
Y-adapter
Wire removed from
LINE OUT jack
B
PHONES
Audio
Cable
B
1/8”
Y-adapter
Headphones/Speakers

16
HOW TO CONNECT YOUR VCR
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 15.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the AUDIO OUT jack on your VCR.
B. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into an RCA Y-adapter (available at electron-
ics stores). Next, remove the wire that is currently
plugged into the AUDIO OUT jack on your VCR
and plug the wire into the unused side of the Y-
adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFIT.com CD’s or videocassettes, the elliptical
crosstrainer must be connected to your portable CD
player, portable stereo, home stereo, computer with
CD player, or VCR. See HOW TO CONNECT YOUR
CD PLAYER, VCR, OR COMPUTER on page 15.
Note: To purchase iFIT.com CD’s and videocas-
settes, call toll-free 1-800-735-0768.
Follow the steps below to use an iFIT.com CD or
video program.
Turn on the power
See step 1 on page 12.
Select the iFIT.com mode
Each time the
power is turned
on, the manual
mode will be
selected. To select
the iFIT.com
mode, press the PROGRAM SELECT button
repeatedly until the iFIT.com indicator lights. Note:
When you press the PROGRAM SELECT but-
ton, the incline will automatically change to the
lowest position.
Insert the iFIT.com CD or videocassette
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the play button on your CD player or
VCR
A moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions.
During the program, the incline and the resistance
of the elliptical crosstrainer will automatically
change according to the settings for the program.
An electronic “chirping” sound will alert you when
the incline and/or resistance is about to change.
4
3
2
1
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
ANT.IN
RF OUT
IN
OUT
CH
34
Audio Cable
A
VIDEO AUDIO
ANT.IN
RF OUT
IN
OUT
CH
34
Audio Cable
B
Wire removed from
AUDIO OUT jack
RCA Y-adapter

17
If the incline or resistance setting is too high or too
low, you can manually override the setting at any time
by pressing the RAMP or RESISTANCE buttons on
the console. However, when the next “chirp” is heard,
the incline and/or resistance will change to the next set-
ting for the program.
Note: If the incline and/or resistance of the elliptical
crosstrainer does not change when a “chirp” is
heard:
• Make sure that the iFIT.com indicator is lit.
• Adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals.
• Make sure that the audio cable is properly con-
nected and that it is fully plugged in.
Follow your progress with the displays
Refer to step 4 on page 12.
Measure your heart rate if desired
Refer to step 5 on page 12.
When you are finished exercising, the console
will automatically turn off
Refer to step 6 on page 12.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
Our Web site at www.iFIT.com allows you to play
iFIT.com audio and video programs directly from the
internet. To use programs from our Web site, the ellip-
tical crosstrainer must be connected to your home
computer. See HOW TO CONNECT YOUR COMPUT-
ER on page 15. In addition, you must have an internet
connection and an internet service provider. A list of
specific system requirements will be found on our Web
site.
Follow the steps below to use a program from our
Web site.
Turn on the power
See step 1 on page 12.
Select the iFIT.com mode
Each time the
power is turned
on, the manual
mode will be
selected. To select
the iFIT.com
mode, press the PROGRAM SELECT button
repeatedly until the iFIT.com indicator lights. Note:
When you press the PROGRAM SELECT but-
ton, the incline will automatically change to the
lowest position.
Go to your computer and start an internet
connection
Start your web browser, if necessary, and go
to our internet site at www.iFIT.com
Follow the desired links on our internet site to
select a program
Read and follow the on-line instructions for using
a program.
Follow the on-line instructions to start the
program
When you start the program, an on-screen count-
down will begin.
6
5
4
3
2
1
7
6
5

Return to the elliptical crosstrainer
When the on-screen countdown ends, the pro-
gram will begin. During the program, the incline
and the resistance of the elliptical crosstrainer will
automatically change according to the settings for
the program. An electronic “chirping” sound will
alert you when the incline and/or resistance is
about to change.
If the incline or resistance setting is too high or
too low, you can manually override the setting at
any time by pressing the RAMP or RESISTANCE
buttons on the console. However, when the next
“chirp” is heard, the incline and/or resistance will
change to the next setting for the program.
Follow your progress with the displays
Refer to step 4 on page 12.
Measure your heart rate if desired
Refer to step 5 on page 12.
When you are finished exercising, the console
will automatically turn off
Refer to step 6 on page 12.
THE INFORMATION MODE
The console features an information mode that keeps
track of the total number of miles that the pedals have
moved and the total number of hours that the elliptical
crosstrainer has been used. The information mode
also allows you to switch the console from miles to
kilometers.
To select the information mode, press the RAMP +
button and the RESISTANCE +button simultaneously
for a few seconds. The following information will be
shown:
The LED matrix will
show a letter E for
English miles or a letter
M for metric kilometers.
Press the RESIS-
TANCE +button to
change the unit of mea-
surement if desired.
The left LED display will
show the total number of
miles that the pedals have
moved.
The right LED display will
show the total number of
hours that the elliptical
crosstrainer has been used.
To exit the information mode, press the right side of
the START/PAUSE button.
9
8
7
18
10

19
For smooth
operation of
the elliptical
crosstrainer,
the incline
ramp should be
kept clean.
Using a soft
cloth and mild
detergent,
clean dust and
other residue from the incline ramp where the wheels
make contact with it. Other parts of the elliptical
crosstrainer can also be cleaned in this manner.
Never use abrasives or solvents.
Inspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.
CALIBRATING THE RESISTANCE AND INCLINE
SYSTEMS
If the elliptical crosstrainer’s resistance or incline sys-
tem is not working properly, you may need to activate
the calibration routine.
To activate the resistance calibration routine, first
adjust the resistance to the lowest setting. Wait for the
resistance motor to stop. Next, press the RESIS-
TANCE + button. While the resistance motor is run-
ning, unplug the power cord from the wall. Wait for a
few seconds and then plug the power cord back in.
The resistance system will now calibrate itself. It will
not need to be calibrated again.
To activate the incline calibration routine, first
adjust the incline to the lowest setting. Wait for the
incline motor to stop. Next, press the RAMP + button.
While the incline motor is running, unplug the power
cord. Wait for a few seconds and then plug the power
cord back in. The incline system will now calibrate
itself. It will not need to be calibrated again.
MAINTENANCE AND TROUBLESHOOTING
Incline
Ramp
Wheel

20
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
To find the proper heart rate for you, first find your age
on the bottom line of the chart (ages are rounded off
to the nearest ten years). Next, find the three numbers
above your age. The three numbers are your “training
zone.” The lowest number is the recommended heart
rate for fat burning; the middle number is the recom-
mended heart rate for maximum fat burning; the high-
est number is the recommended heart rate for aerobic
exercise.
To measure your heart rate, use the pulse sensor
(see step 5 on page 12).
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
WORKOUT GUIDELINES
Each workout should include the following three
important parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise (see SUGGESTED STRETCHES
on page 21). A proper warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise
program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
WARNING:
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.