hergom E-30 Series Quick start guide

E-30
INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS.

3
INDUSTRIAS HERGÓM, S.L., may not be held liable for any damages caused by alterations in its
products that have not been authorised in writing, or for defective installation work.
Furthermore, it reserves the right to change its products without prior warning.
Industrias Hergóm, S.L. domiciled in Soto de la Marina (Cantabria) - Spain, offers a THREE YEARS
warranty on its products. Industrias Hergom, S.L. guarantees the existence of repair parts and
adequate technical service for 10 years from the date on which this product ceases to be
manufactured.
The geographical coverage of the said warranty only includes the countries in which Industrias
Hergom, S.L., a subsidiary company or an official importer distribute its products and where
Community Directive 2019/771/UE is in force.
The warranty comes into force on the purchase date of the product as indicated on the warranty
document and only covers damage or breakages due to manufacturing defects.
IMPORT ANT NOTE
If the device is not installed correctly, it will not provide the excellent service for which it has been
designed. Please, read these instructions in full and trust the work to a specialist.
The surface of your device is protected by a coat of special anti-heat paint that resists high
temperatures. When lighting the fireplace for the first few times, the said paint may emit some
fumes. This is normal and is due to the evaporation of certain components of the paint while it
adapts to the heat. We, therefore, recommend ventilating the room until this phenomenon ceases
to appear.
WELCOME to the HERGÓM family.
We would like to thank you for choosing our E-30 Stove, which represents, in technique and style,
a significant improvement on typical wood stoves.
Your new Stove is, perhaps, the most advanced solid fuel heating system known today. Owning a
HERGOM Stove displays an exceptional sense of quality.
Please read this manual in full. Its purpose is to familiarise users with the device by explaining
extremely useful installation, operational and maintenance instructions. Keep this manual at hand
for future reference whenever necessary.
If, after reading this manual, you should require any further clarification, please consult your
regular dealer.

4
Outside air
connection
1 - INTRODUCTION
IMPORTANT! All local regulations, including those
that refer to national or European regulations, must
be applied when installing this device.
The way the E-30 Stove is installed will decisively
affect safety issues and its correct operation.
It is important to install the fireplace correctly. For the
correct installation of the E-30 Stove and chimney, we
recommend the installation be performed by a
professional.
The E-30 Stove provides heat by radiation; directly
heating walls, ceilings...
2 - PRESENTATION
E-30 wood stoves have the following main features:
•Made in 3 sizes: L, M and S, to meet each users’
heating requirements.
•Made of cast iron, with parts that are assembled,
sealed and screwed together.
•Cast iron white enameled lined.
•They are designed for use with firewood only.
•They can burn pieces of wood up to 40, 50 or 60
cm. in length, depending on the model.
•Lighting up valve
•Primary air adjustment valve.
•Self-cleaning glass.
•Hinged front door opening 180º with ceramic glass
pane.
•Ash pan with cover
•Optional outside air connection located on the
back of the ash pan.
•Vertical top smoke flue
•Fully factory assembled, ready for connection to
the chimney.
Door handle
Primary/glass pane
cleaning air valve
Lighting up valve
Ash-pan
FIG. 2

5
3 - USING THE STOVE
Once your stove has been installed and connected to
the chimney, you are ready to light the fire.
Although your stove is easy to use, the combustion
process of solid fuels is complicated, as it involves
several factors and it takes time and experience to
understand the process.
Before lighting your stove for the first time, please
take time to become familiar with the different
control systems and parts of the unit, how to choose
the wood, how to light it and use it on a daily basis.
ALWAYS KEEP IN MIND that the stove generates heat
and, therefore, keep children, clothing, furniture... at
a distance to prevent burns from direct contact with
the appliance.
Below, we have included some advice on your stove
and on its use. Please read with care.
Door handle
To open the door, turn the handle upward to the open
position, and gently pull.
The door can open up to 180º
To close, turn the knob to the open position, close the
door, press slightly and turn the handle gently down
to the closed position (Fig. 3).
FIG. 3
Lighting up valve
Fully open the valve when lighting the stove (Fig. 3
Adjustment - Glass Cleaning Valve
Fully open the glass pane cleaning air valve when
ighting the stove.
Once an ideal combustion rate has been achieved,
adjust the vale to prevent excessive air intake, which
will cause excessive combustion levels and
temperatures.
The intermediate position is usually the ideal
adjustment, depending on the quality of the draw of
the chimney installed and on the type of fuel being
used (hard or soft wood) (Fig. 3).
Ash pan
Very important!
Only handle the ash pan when the stove is cold.
Always avoid opening the ash-pan if your stove is in
operation.
To clean the ash, lift the blind grill located at the
bottom of the stove.
Use a tool (brush) to sweep the ash into the ashpan.
The ash-pan is removed from under the stove tray (Fig.
4).
To remove the ash-pan from its position, pull the
handle gently to release it.Once you have emptied the
ashes, return the ash pan to the ash drawer, pushing
it into place to create a seal.
Do not forget to replace the cover in the bottom of the
fire box.
OPEN
CLOSE
CLOSE
OPEN
CLOSE
OPEN
FIG. 4

6
4 - LIGHTING UP AND USE
Important at first start: may come off a few drops of
condensed water from the stove, produced by the
humidity of the environment where the stove was
stored.
It is very important that the first time the heater is lit,
it is done so slowly.
This is for the following reasons:
•Stabilise cast iron parts.
•Harden the joint sealant putty. Advise:
•We recommend that the first loads of fuel be small.
•To generate draw, heat the chimney by introducing
some burning paper in the gap between the front
and the deflector, directing it toward the chimney.
•While lighting for the first time, ensure the room
where the heater is located is well ventilated as the
paint work may let off some fumes.
•Keep the stove on for a few hours at this intensity.
•IMPORTANT! The total height of the fire load
should not exceed 50% of the height of the
combustion chamber.
•The heater must be closed at all times during
combustion to prevent smoke from leaking out.
Only open to add fuel.
Daily use
After lighting up for the first time, your heater will be
ready for daily use.
Your heat requirements will be obtained based on the
frequency and the amount of firewood you load.
When your heater is cold, we recommend lighting it
up slowly.
Overheating.
Overheating means that you have operated your
heater at a excessively high temperatures for a long
period of time. This can damage your appliance and,
therefore, it is a situation that must be avoided.
Overheating is the result of excessive draw, due to any
of the following reasons:
•The Primary Air Valve is excessively open for the
type of wood being used.
•The chimney is too big.
•Improper maintenance of the stove, which may
result in air infiltration.
•Inappropriate fuel that produces high
temperatures.
•Door not closed correctly.
ATTENTION!
During the operation of the stove, the ash pan cover
must be perfectly positioned to seal the fire box.
Any uncontrolled intake of air produces overheating
that can damage the stove.
HEATERS WITH ENAMEL IN MAJOLICA VERY
IMPORTANT!
In the case of stoves enamelled in Majolica, it is
normal for slight fissures to appear in the glazing,
providing the product with its characteristic
appearance, once the heater is lit.
However, in the event of uncontrolled overheating,
these fissures caused by the different expansion
levels of the cast iron and the Majolica enamel with
vitreous components, can cause the enamel to chip.
To avoid this inconvenience, control combustion and
never overheat the heater.
INDUSTRIAS HERGÓM S.L. may not be held liable
for the deterioration of the stove’s enamel if these
instructions are not followed.
HANDLE
FIG. 5

7
5 - CLEANING & MAINTENANCE
Your heater is a device that is subjected to extreme
temperatures and to the corrosive effects of
combustion residual materials. Regular maintenance
is essential for a longer life and improved user
experience. We recommend performing the following
inspections frequently.
DURING THE SEASON
•Perform a visual inspection of the chimney. Clean
soot and tar if they have begun to accumulate on
the inner walls of the heater.
•Check whether the doors close tightly; adjust if
necessary.
AT THE END OF THE SEASON
•Inspect and clean the chimney.
•Use the vacuum cleaner to clean inside the heater
and inspect it.
•Any soot and tar (creosote) that has accumulated
on the walls of the heater will hinder performance.
•Inspect door seals. These should be replaced when
they no longer seal the door perfectly.
•In the case of painted heaters, paint the cast iron
parts again if necessary
CLEANING
Cleaning should always be performed when the
heater is cold.
Cleaning ash.
These heaters are equipped with an ash pan located
at the bottom of the heater.
Remove the ash pan and remove the ash.
Ash should be emptied into a metal container and
immediately removed from the house.
If necessary clean the ash pan housing.
Enamelled parts.
Preferably use a damp cloth.
Do not used strong or abrasives detergents that might
damage the surface.
Painted parts
Clean with a dry cloth to avoid rust.
Chimney and connecting unit
Read the chapter in the Manual for Installers that
refers to this topic.
DOOR PANES
Cleaning
Fireplace window cleaning liquids are quite effective
products.
Never try to clean the glass while the fireplace is
working.
We recommend using HERGOM window cleaning
products for their proven efficacy.
If the glass pane on the fireplace door is constantly
covered in soot, this means your fire is “poor” and that
the connecting pipe and chimney are being blocked by
soot and creosote.
Replacing.
The glass panes in your heater have been especially
manufactured for log stoves.
If they should break, they must be replaced by another
glass pane with the same technical specifications.
Contact our Distributor to provide you with the
appropriate glass pane, together with instructions to
assemble and seal.
MAINTENANCE PRODUCTS
Industrias HERGÓM, S.L. places a range of products for
the preservation of your heater and chimney at your
disposal: heat resistant paint, refractory putty, anti-
soot products, fire-lighters, glass cleaning products.

8
6 –PRODUCT RECYCLING
Your appliance is delivered packed in plastic and a
cardboard box on a wooden pallet. You can use
cardboard and wood as fuel for the first lightings of
the appliance, or take it to a local recycling point. The
plastic that protects the device must be taken to a
specific local recycling point or center, it must not be
disposed of in conventional waste dumpster.
All local regulations, including those that refer to
national or European regulations, must be applied
when recycling this device at the end of its useful life.
The product should never be disposed of in
conventional waste dumpster. Its appliance is made
up of components made of cast iron, steel, glass,
insulating materials and electrical material, which are
assembled using screws and rivets. You can
disassemble it and take it to a specific local recycling
point or center. Glass should not be disposed of in
conventional waste dumpster.
7 - SAFETY
WARNING!
Gas/log/pellet units get hot when in use.
Consequently, owners must act with precaution and
keep at a distance. Especially keep children,
the elderly and other people who require special
supervision, as well as pets, away from the fireplace
when it is in use.
Make sure that children or other people who are not
familiar with how the device works are supervised by
responsible people when they are near the fireplace.
In order to prevent burns or children or other people
from coming near the appliance, use a fire grille or
screen.
A number of possible risks are present when operating
your solid fuel oven with fuel of any brand. The said
risks can be minimised if the instructions and
recommendations included in this manual are
followed.
•When installing the stove, observe the necessary
safety distances for the oven and chimney from
combustible surfaces (wooden or papered walls,
wooden floors...). Safety distances must be
respected when the lining on walls or nearby areas
may be damaged or deformed by temperature
(varnish, paint, PVC...). Fig. 6
•The base where you are going to install your heater
must be flat and provide a perfect seat. The said
base must also be capable of supporting the weight
of the heater. The base must be built using heat
resistant materials.
•All the area around the heater should must be heat
resistant. If not, they must be protected by fire-
proof material.
•Ash should be emptied into a metal container and
immediately removed from the house.
•Do not use flammable liquids to light the stove.
Keep any type of flammable liquid (petrol,
gasoline, alcohol,....) at a distance from the
fireplace.

9
•Never use coal or fuels that are not recommended
for the operation of this product.
•Periodically inspect the chimney and clean
whenever necessary. Also inspect the state of
joints, glass, screws...
•Protect your hands with a glove or other insulating
material because, during operation, the opening
and closing handle will be hot.
OUTSIDE AIR CONNECTION
•When installing the stove using the outside air
connection, we recommend that the installation is
performed by qualified personnel.
•Always keep in mind that air is entering the stove
through the connector. This air inlet can never be
blocked. Ensure that the pipe connecting the stove
to the outside cannot be crushed and that the
entrance to the pipe cannot be blocked on the
outside. It is necessary to cover the inlet with a
protective grill.
•The location of the outside air inlet of air must be
protected from the wind to avoid a possible
positive or negative pressure from affecting the
combustion of the stove.
•Refer to the technical specifications at the end of
this manual for the minimum diameter and the
maximum length of the pipe to be connected.
FIG. 6 - SAFETY DISTANCES

10
8 - DIMENSIONES - DIMENSIONI - MEASURES - DIMENSIONS - DIMENSÕES
mm
E-30 S
E-30 M
E-30 L
A
280
310
325
B
380
440
520
C
740
785
810
D
700
740
770
E
120
120
140
F
210
225
225
G
420
470
540
H
490
545
615
I
590
660
750
J
150
150
200
L
150
162
162

11
9 - DATOS TECNICOS - DATI TECNICI - TECH SPEC. - DONNÉES TECH. –DADOS TÉCNICOS
E-30 S
E-30 M
E-30 L
Potencia nominal / Potenza nominale / Nominal power / Puissance
nominale / Potência nominal (kW)
7
9
11
Temperatura de los gases medio / Temperatura media gas / Average
smoke temperature / Température des gaz moyenne / Temperatura
média dos gases (°C)
288
281
274
Temperatura media en collarín de salida / Temperatura media attacco
scarico fumi / Average temperature at flue ring / Température moyenne
sur buse de sortie / Temperatura média em anel de saída (°C)
300
340
375
Caudal másico de los humos / Portata massima fumi / Mass flow rate of
smoke / Débit massique des fumées / Caudal mássico dos fumos (gr/sec)
6,9
8,6
10,4
Emisiones CO / Emissioni CO / CO emissions / Émissions CO / Emissões CO
(13% O2 Vol%)
0,1
0,1
0,1
Rendimiento / Rendimento / Efficiency / Rendement / Rendimento (%)
79,1
79,2
79,3
Admite troncos de leña de longitud / Lunghezza max legna / Accepts logs
of the following length / Admet des bûches de longueur / Admite troncos
de lenha de comprimento (mm)
400
500
600
Collarín de humos / Attacco scarico fumi / Smoke collar / Buse de fumées
Anel de fumos (Ø - mm)
150
150
200
Chimenea metálica / Canna fumaria metallica / Metal chimney / Cheminée
métallique / Chaminé metálica (Ø - mm)
150
150
200
Altura recomendada de chimenea / Altezza consigliata canna fumaria /
Recommended chimney height / Hauteur de cheminée recommandée /
Altura recomendada de chaminé (m)
5-6 (*)
5-6 (*)
5-6 (*)
Chimenea de albañilería mín. aprox. / Canna fumaria in muratura min.
circa / Masonry chimney, min approx. / Cheminée en maçonnerie min.
approx. / Chaminé de alvenaria mín. aprox. (mm)
200x200
200x200
250x250
Tiro recomendado / Tiraggio consigliato / Recommended draw / Tirage
recommandé / Tiragem recomendada (Pa)
12
12
12
Salida de humos / Scarico fumi / Smoke outlet / Sortie de fumées / Saída
de fumos
Vertical
Vertical
Vertical
Peso / Peso / Weight / Poids / Peso (Kg)
110
150
190
Entrada aire del exterior / Entrata aria esterna / Outside air inlet / Entré
d´air depuis l´extérieur / Entrada ar do exterior (Ø mm)
80
80
80
Diámetro minimo de tubo de conexión entrada aire exterior / Diametro
minimo del tubo di connessione entrata aria esterna / Minimum diameter
of the outside air inlet pipe / Diamètre minimum du tuyau de connexion
entrée d’air extérieur / Diâmetro mínimo do tubo de ligação entrada ar
exterior (Ø mm)
80
80
80
Longitud máxima de tubo de conexión entrada aire exterior / Lunghezza
massima del tubo di connessione entrata aria esterna / Maximum length
of the outside air inlet pipe from outside / Longueur maximum tuyau de
connexion entrée d’air extérieur / Comprimento máximo de tubo de
ligação entrada ar (m)
> 8m.
Consultar
Interpellare
Consult
Consultez

12
(*) Para otras medidas consultar al Distribuidor o al
Fabricante. (Valores Aproximados.)
Estufa homologada siguiendo las especificaciones de
la norma UNE-EN 13240:2002 “Estufas que utilizan
combustibles sólidos –Requisitos y métodos de
ensayo”, modificada por UNE-EN 13240/AC y UNE-EN
13240:2002/A2.
¡ADVERTENCIA! Su estufa no debe ser utilizada como
incinerador y no deben utilizarse otros combustibles
(plásticos, aglomerados, etc). Utilice los materiales
recomendados.
No usar como combustible maderas que provengan
del mar. Las sales contenidas en ella reaccionan en la
combustión liberando ácidos que atacan al hierro y
acero.
(*) Per altre dimensioni, interpellare il distributore o il
costruttore. (valori approssimativi)
Stufa omologata secondo le specifiche della norma
UNI-EN 13240:2002 “Stufe a combustibile solido -
Requisiti e metodi di prova”, modificata dalle norme
UNI-EN 13240/CA e UNI-EN 13240:2002/ A2.
AVVERTENZA! La stufa non deve essere usata come
inceneritore e non si devono usare altri combustibili
(materiali plastici, agglomerati, ecc). Usarei materiali
consigliati.
Non usare quale combustibile la legna portati in riva
dal mare. I sali che contiene reagiscono durante la
combustione liberando acidi che intaccano il ferro e
l’acciaio.
(*) In the case of other dimensions consult your Dealer
or the Manufacturer (Approximate Values)
Stove approved based on the specifications provided
in UNE-EN 13240:2002 “Room heaters fired by solid
fuel - Requirements and test methods”, as amended
by UNE-EN 13240/AC and UNE-EN 13240:2002/A2.
ATTENTION! Your heater should not be used as an
incinerator and no other types of fuel should be used
(plastic, chipboard…). Use recommended materials
only.
Do not wood washed ashore from the sea as fuel.
The salt contained in it will react in the combustion
process and release acid that will damage the iron
and steel.
(*) Pour d’autres mesures, consultez le distributeur ou
le fabricant (valeurs approximatives).
Poêle homologué conformément aux spécifications
de la norme UNE-EN 13240:2002 “Appareils de
chauffage utilisant du combustible solide - Exigences
et méthodes d’essai » modifiée par UNE-EN
13240/AC et UNE-EN 13240:2002/A2.
AVERTISSEMENT! Votre poêle ne doit pas être utilisé
comme incinérateur et il ne faut pas utiliser d’autres
combustibles (plastiques, agglomérés, etc.) que ceux
recommandés.
N’utilisez pas comme combustible de bois rejeté par
la mer. Les sels qu’il contient réagissent à la
combustion en libérant les acides qui attaquent le fer
et l’acier.
(*) Para outras medidas, consultar o Distribuidor ou o
Fabricante. (Valores Aproximados.)
Estufa homologada seguindo as especificações da
norma UNE-EN 13240:2002 “Estufas que utilizam
combustíveis sólidos –Requisitos e métodos de
ensaio”, modificada pela UNE-EN 13240/AC e a UNE-
EN 13240:2002/A2.
ADVERTÊNCIA! Esta estufa não deve ser utilizada
como incinerador e não se deve de utilizar outros
combustíveis (plásticos, aglomerados, etc). Utilize os
materiais recomendados.
Não utilizar como combustível madeiras que venham
do mar. Os sais que contêm reagem na combustão
liberando ácidos que atacam o ferro e o aço.

13
10 - DESPIECE - ESPLOSO - EXPLODED VIEW - EXPLOSÉ –EXPLODIDO

14
11 - PIEZAS DE REPUESTO - RICAMBI - SPARE PARTS - RECHANGES –SOBRESSALENTES
N°
E30 S HF
E30 M HF
E30 M HF
CREMA
E30 L HF
DENOMINACIÓN
1
9920164
9920165
9920912
9920166
ENCIMERA
2
9920167
9920168
9920168
9920169
VARILLA AMARRE ESTUFA
3
9920170
9920171
9920913
9920172
COSTADO IZQUIERDO
4
9920680
9920681
9920681
9920682
PLACA DEFLECTOR HIERRO FUNDIDO
5
9920674
9920655
9920655
9920675
COSTADO INTERIOR IZDO
6
9920179
9920180
9920180
9920181
CONJUNTO FIBRA DE VIDRIO
7
9920182
9920182
9920182
9920182
PARRILLA
8
9920183
9920184
9920184
9920185
COLECTOR PRIMARIO
9
9920186
9920187
9920914
9920188
FRENTE
10
9920193
9920193
9920193
9920193
TRENZA FIBRA CERAMICA 3/8" (3 m)
11
9920189
9920190
9920190
9920191
CONJUNTO CRISTAL
12
9920192
9920192
9920192
9920192
TRENZA FIBRA CERAMICA 1/4" (3 m)
13
9920194
9920195
9920915
9920196
CONJUNTO PUERTA HOGAR
14
9920197
9920197
9920197
9920197
CONJUNTO BISAGRA PUERTA HOGAR
15
9920683
9920683
9920683
9920683
SUFRIDERA DEFLECTOR
16
9920656
9920656
9920656
9920656
CONJ. MANDO CIERRE PUERTA HOGAR
17
9920057
9920057
9920057
9920057
EJE CIERRE PUERTA HOGAR
18
9920447
9920445
9920916
9920448
CONJUNTO CENICERO
19
9920203
9920204
9920917
9920205
FONDO
20
9920206
9920206
9920206
9920206
MANDO VALVULA ENCENDIDO
21
9920207
9920207
9920207
9920207
MANDO VALVULA CRISTAL
22
9920208
9920208
9920208
9920208
TUBO VALVULA ENCENDIDO
23
9920446
9920446
9920446
9920446
CUERPO CAJON PARA CENICERO
24
9920211
9920212
9920918
9920213
COSTADO DERECHO
25
9920678
9920657
9920657
9920679
TRASERA INTERIOR
26
9920223
9920224
9920919
9920225
TRASERA
27
9920676
9920658
9920658
9920677
COSTADO INTERIOR DCHO
28
-----
9920920
9920920
-----
CHAPA PROTECTOR TRASERA
29
-----
9920921
9920921
-----
CHAPA PROTECTOR TECHO

15
15
9920683
9920683
9920683
9920683
SUFRIDERA DEFLECTOR

16
Debido a la similitud estructural de los tres tamaños de estufas, le adjuntamos el listado de repuestos en base a la
vista explotada de la estufa E-30 M mostrada en las páginas anteriores. Se recomienda usar piezas de repuesto
recomendadas por el fabricante.
Data la somiglianza strutturale delle tre dimensione di stufe, si allega il relativo elenco dei pezzi di ricambio, in base
all’esploso della stufa E-30 M riportato nelle pagine precedenti.
Si consiglia di usare esclusivamente i pezzi di ricambio consigliati dal costruttore.
Due to the structural similarity of the three stoves sizes, please find enclosed the list of spare parts for both, based
on the exploded view of the E-30 M, displayed on the previous pages. We recommend using spare parts
recommended by the manufacturer.
La similitude de structure des trois tailles de poêles est semblable et nous adjoignons ci-dessous la liste des pièces
de rechange communes, explication de la vue explosée du poêle E-30 M figurant sur les pages précédentes. Nous
conseillons l’utilisation des pièces de rechange recommandées par le fabricant.
Devido à similitude estrutural das três tamanhos de estufas, juntamos a listagem de sobressalentes de ambas, sobre
a base da vista das peças da estufa E-30 M nas páginas anteriores.
Recomenda-se utilizar peças sobressalentes recomendadas pelo fabricante.
INDUSTRIAS HERGÓM, S.L. declina toda responsabilidad derivada de una instalación defectuosa o de una
utilización incorrecta y se reserva el derecho de modificar sus productos sin previo aviso.
La responsabilidad por vicio de fabricación, se someterá al criterio y comprobación de sus técnicos, estando en todo
caso limitada a la reparación o sustitución de sus fabricados, excluyendo las obras y deterioros que dicha reparación
pudiera ocasionar.
INDUSTRIAS HERGÓM, S.L. declina ogni responsabilità derivante da un’installazione difettosa o da un uso errato e
si riserva il diritto di modificare i propri prodotti senzapreavviso.
La responsabilità per vizi di produzione sarà sottoposta al giudizio e alla verifica dei propri tecnici e in ogni caso sarà
limitata alla riparazione o alla sostituzione degli apparecchi, escludendo eventuali lavori e deterioramenti che la
riparazione potrebbe provocare.
INDUSTRIAS HERGÓM, S.L., rejects any liability derived from a faulty installation or incorrect use and reserves the
right to alter its products without prior warning.
Any liability due to manufacturing defects will be subject to the criteria and verification of the company’s experts
and will be limited to the repair or replacement of its products, excluding any construction work or damage the said
repairs may cause.
INDUSTRIAS HERGÓM, S.L. décline toute responsabilité relative à une installation défectueuse ou à une utilisation
incorrecte et se réserve le droit de modifier ses produits sans avertissement préalable
La responsabilité pour vice de fabrication sera soumise au critère et à l’approbation de ses experts techniciens et
se traduira, limitée dans tous les cas, par la réparation ou le remplacement de ses pièces fabriquées excluant les
ouvrages et détériorations qui découleraient de cette réparation.
A INDUSTRIAS HERGÓM, S.L. declina qualquer responsabilidade derivada de uma instalação defeituosa ou de uma
utilização incorreta e reserva-se o direito de modificar os seus produtos sem aviso prévio.
A responsabilidade por vício de fabricação, será submetida ao critério e à verificação dos técnicos da empresa
Hergom e estará sempre limitada à reparação ou substituição dos seus produtos, excluídas as obras e o deterioro
que a referida reparação poderia ocasionar.

17

INDUSTRIAS HERGOM S.L
SOTO DE LA MARINA - CANTABRIA
Apdo. de correos 208 SANTANDER
Tel: [phone]
E-mail: [e-mail]
www.hergom.com
C07100AA130
Revisión 10
ED: 08/2022
18