Herman Miller Intent Furniture Leg Kit Installation instructions

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
1
Y
Parts Included:
Tools Needed:
Intent®Furniture Leg Kit Installation and Disassembly for
Recycling Instructions
Post Leg
Closed Leg Mounting Brackets (2)
Open Leg
Shared
Open Leg
Shared
Closed Leg
Flat Head Machine Screw
Flat Head Machine Screw (2)
Flat Head Wood Screw (8)
1.0” Long Bright Zinc
Flat Head Wood Screw (8)
1.25” Long Black
Tapping
Screw (10)
Tapping
Screw (6)
Tapping
Screw (15)
Mounting
Plate
Flat Head Wood
Screw (26)
Mounting Plate
Leg Options
Glide (2)
Glide (2)
Glide (2)
Hardware Pack
Hardware Pack
Hardware Pack
Hardware Pack
Hardware Pack
E
MP
L
S
T
H
J
W
X
K
K
K
V
R
F
G
G
G
Power Driver Phillips Bit 1/8” Drill Bit Level
Safety Glass

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
2
Post Leg Installation:
1. Attach Mounting Plate (F) to Post Leg (E) with Flat head screw (H & J).
2. Install Post Leg on to Work Surface with 8 Flat Head Screws (W) 1.00” long bright
zinc plate for all work surface types except for thin edge laminate. Then use 8 at
head screws black plate (X) 1.25” long. NOTE: Do not use 1.25” black plate screws in
other applications which will result with screw breaking thru the work surface top.
Locate Leg 3/32” in from edge of Work Surface.
3. Install Glide (G) into end of leg.
3/32” 3/32”
H
F
E
J
W or X

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
3
Open Leg Installation:
1. Install Glides (G) onto Open Leg (L)(S).
2. Attach Open Leg to underside of Work Surface with Tapping Screws (K).
3. Open Leg should be positioned so that Flat Mounting Plate is Front of Desk.
4. Position Adjacent Work Surface to installed surface.
5. Install 3 Tapping Screws (K) to gang surfaces together.
G
G
S
K
K
K
L
Flat Mounting
Plate
Adjacent Surface
Front Of
Desk

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
4
Closed Leg Installation:
1. Attach Mounting Brackets (P) to Panel with 12 Tapping Screws (R).
2. Align Mounting Bracket with Pilot holes in underside of Work Surface.
3. Install Tapping Screws (R).
4. In some desk type, 1/8” dia pilot holes will need to be drilled, 1/2” deep.
P
M
R
R
R
R
R
Pilot Holes
Pilot Holes

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
5
1. Install Mounting Plate (V) to Closed Leg (T) with 9 Tapping Screws (K).
2. Attach Leg to underside of Work Surface (A) with 3 Tapping Screws (K).
3. Position Adjacent Work Surface to installed surface.
4. Install 3 Tapping Screws (K) to gang surfaces together.
K
K
K
A
V
T
Closed Shared Leg Installation:

Z
© 2017 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Intent are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b59wr rev F.
6
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet
for recycling. Non-ferrous metals should be separated and recycled separately.
To disassemble product, reverse the above installation steps: