Herman Miller Renew Link User manual

Tools Required
HermanMiller
Renew ™ Link Installation
Y
How to assemble
your table
Parts Included
Power Driver Philips-Recess Bit
Size: #2
1/2” Socket Wrench
© 2015 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 1bfnlt - A.
TM Renew is among the trademarks of Herman Miller, Inc.
For more information about our products and services or to see a list of dealers,
For assistance: Please visit us at www.hermanmiller.com/product-instructions or call 888-443-4357
Illustrations and specications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specications at any time, without notice, and also to discontinue
products.
Base product number (DU)
Notice:
Some of the parts have been wrapped to protect them during shipping. Remove the plastic
wrap before assembling the table.
Assemble products on a protective surface.
Note: Not all the parts shown above are applicable for all the tables.
Tapping Hex
Head Screw
Connector Bracket
L - Bracket Hex Bolt
End Cap C
A
D E
B
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed,
including the following:
Read all instructions before using this furnishing.
DANGER - To reduce the risk of electric shock always unplug this furnishing from the
electrical outlet before cleaning.
WARNING - To reduce the risk of burns, re, electric shock, or injury to persons:
Close supervision is necessary when this furnishing is used by, or near children,
invalids, or disabled persons.
Sitting or standing on product may cause risk of personal injury (use for chairs, tables
consider obvious misuse of product).
Use this furnishing only for its intended use as described in these instructions. Do not
use attachments not recommended by the manufacturer.
Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the
furnishing to a service center for examination and repair.
Failure to fully tighten screws (bolts) may cause injury by causing Renew tables to
collapse. Tighten screws (bolts) until they stop plus a quarter turn.
Periodically check to make sure legs are properly aligned. Failure to do so may
cause risk of personal injury.
If using power drive set on low torque.
Keep the cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where oxygen is
being
administered.
This furnishing is intended for commercial use
control box rating: 4.8A, 120V
Max FPDU rating: 15A, 120V
Duty cycle: 1min on, 18min o
Use extension bit if required, Magnetic bits are recommended.
Not all tools are used on all tables.
HermanMiller RenewTM Bench (Height Adjustable - Electrical)
Assembly Instructions
1Part no. 1bfnlt rev A.
SAVE THESE INSTRUCTIONS

HermanMiller RenewTM Bench (Height Adjustable - Electrical)
Assembly Instructions
2Part no. 1bfnlt rev A.
WARNING - Risk of Electric Shock – Connect this furnishing to a properly grounded outlet
only. See Grounding Instructions.
For loading always put heavier items in the center and distribute the load.
Maximum load rating is 120 lbs.
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER – Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualied electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product.
if it will not t the outlet, have a proper outlet installed by a qualied electrician.
This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like
the plug illustrated in Sketch A. Make sure that the product is connected to an outlet having
the same conguration as the plug. No adapter should be used with this product.
GROUNDED
OUTLET
GROUNDED
PIN
(A)
Step 1
DU1 Version
End Cover Installation
1.1 Place end cover over the Leg Brace.
B
Step 2
Connector Brackets Installation
3.1 Level DU1 tables by adjusting the 4 glides.
3.2 Tighten the connector bolts securely.
3.3 Place the top cover in place over the leg braces.
3.4 Hold the bottom cover in place and attach with provided hardware using #2 philips.
L - Bracket Installation
2.1 Loosely connect the two DU1 table together using the L - Bracket (D) and hardware (E)
using 1/2” socket, align slots vertically.
2.2 To adjust glides lift edge of table and spin glides with your ngers.
2.3 First focus on leveling the tables independently, then if enough adjustment is available
in the glides level the tables to the adjacent tables.
Step 3
A

HermanMiller RenewTM Bench (Height Adjustable - Electrical)
Assembly Instructions
3Part no. 1bfnlt rev A.
Step 4
Step 6
Step 5
DU2 Version
End Cover Installation
4.1 Place end cover over the Leg Brace.
L - Bracket Installation
5.1 Loosely connect the two DU1 table together using the L - Bracket (D) and hardware (E)
using 1/2” socket, align slots vertically.
Connector Brackets Installation
6.1 Level DU1 tables by adjusting the 4 glides.
6.2 Tighten the connector bolts securely.
6.3 Place the top cover in place over the leg braces.
6.4 Hold the bottom cover in place and attach with provided hardware using #2 philips.
D
E