Herman Miller Mora Administrator Guide

Parts Included
Additional Products Needed - Sold Seperately
Tools Required
HermanMiller
Mora™System ADA Installation and
Disassembly for Recycling Instructions.
How to assemble your ADA
Ch607 Surface
Toggle Bolt (4)
# x / Pan Head
Tapping Screw(4)
# x  Pan Head
Machine Screw(4)
LH End Panel RH End Panel Lower Front Panel
Upper Front Panel Back Support (2) Front Support
Support Bracket (2) Female Hafele
Push-In Clip (6) Male Hafele
Push-In Clip (6)
LH End Panel LH End Panel
Pan Head Shoulder
Screw (32) #6- x / Flat CS
Tapping Screw (24)
Step 1 Step 2
. Attach Support Brackets to Side Panels with  Shoulder Screws.
. Attach  Male Push-In Clips per side panels with  Flat Head Screws.
. Start  Shoulder Screw at each Front and Back Support attachment
location as shown.
. Position Back Supports onto Shoulder Screws in Side Panels.
Back Support
Flathead Screws
Support Bracket
Shoulder Screw
Shoulder Screw
Shoulder Screw
Back Support
Shoulder Screw
Male Push-in Clip
Power Driver
Level
Phillips Bit Stud Finder
Laser Level &
Tripod
Drill Bit
Tape Measure Pencil Safety Glass
HermanMiller for Healthcare Assembly Instructions11BM3WH rev B

HermanMiller for Healthcare Assembly Instructions21BM3WH rev B
. Using level, mark horizontal line on wall ” AFF (above floor nish)
height of sink surface.
. With assistance align top edge of support with marked line on wall.
Allow /” space between end of support and any adjacent wall of cabinet.
Determine and mark appropriate locations for installing support fasteners
which must be no more than ” appart. Also location of rst fastener from
support end must be no more than ”. Use walll studs whenever possible for
support attachment.
Note: If ADA units are installed as “stand alone”, they must have  stud
attachment points or or have  gauge sheet metal backer in wall, attached to
studs, to attach  anchors to.
. Drill /” holes through drywall. Make sure there are no utilities present.
. Insert wall anchors into holes. Orient toggles vertically. Secure to wall.
. Secure supports to side panels with  additional shoulder screws per
support.
. Tighten all screws.
. Position front support onto Side Panels.
Toggle Bolt
. Secure support to side panels with  additional shoulder screws per
support.
. Tighten all screws.
Step 3
Step 5
Step 4
Front Support
Tighten
Mark Holes
Mark Holes
Shoulder Screw
Shoulder Screw
Shoulder Screw

HermanMiller for Healthcare Assembly Instructions31BM3WH rev B
Wall Stud
Wall Stud
Flathead Screws
Flathead Screws
Female Push-In Clip
Female Push-In Clip
Lower Front Panel
Upper Front Panel
Step 6 Step 7
Step 8
/” Toggle Attachment
/” Toggle Attachment
Supplied with Toggle
. Place ADA on wall. Insert screws provided with wall anchor. If screw hole
aligns with wall stud, use /”Toggle Attachment.
. Install surface onto ADA.
. Drill /” Pilot Holes /” deep in underside of surface.
. Secure surface to module with pan head screws provided.
. Install Female Push-In Clips onto Front Panels.
Correct Incorrect

HermanMiller for Healthcare Assembly Instructions41BM3WH rev B
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling
codes. Use these codes to identify material type for recycling. Non marked
components should be treated as mixed plastic. Ferrous metals can be
identied using a small magnet for recycling. Non-ferrous metals should be
separated and recycled separately.
To disassemble product, reverse the above installation steps.
Lower Front Panel
Upper Front Panel
Step 9
. Align clips on fronts with clips on surround assembly. Push in.