HIK VISION Pyronix Enforcer V10 Operating instructions

Enforcer
Extended Programming Guide
Alarm Panel
Time 10:09 c
Version 01

2Enforcer V10 Programming Guide
Contents
Default Codes 4
Access Codes 4
Clean Start Codes 4
Other Codes 4
Technical Support 4
The Engineer Menu 5
Accessing The Engineer Menu 5
Exiting The Engineer Menu 5
Useful Menu Options 5
Wireless device control 5
General Information 6
Default Codes 6
Initial Power Up 6
Wired Keypads/Readers 6
Keypads 7
The Internal Tag Reader (EUR-107) 7
The External Tag Reader (EUR-108) 7
Text Programming 8
Engineer Function: Set System 8
Engineer Function: Forced Arm On Inputs
8
The Engineer Menu 9
Set Date & Time 9
Wireless Device Control 10
Learning Inputs 10
Learning Bells 11
Program Keyfob Buttons 12
Control Arming Stations 12
Change Inputs 13
Input Attributes 14
Change Inputs Programming 14
Choose Mode 15
Choose Mode Programming 15
Install ZEMs 16
Install ZEMS Programming 16
Change Outputs 16
Change Output Programming 17
Assign Keypads/Readers 17
Programming Keypads 19
Programming Readers 19
Wireless Arming Station Options 20
Change Timers 21
Change Timers Programming 21
Codes And Users 21
Change Duress Codes 22
Change Master Manager Code 22
Change Engineer Code 22
Change Codes Programming 22
Volume Control 22
Volume Control Programming 23
System Options 24
Site Options 24
Site Options Programming 26
System Displays 26
System Displays Programming 27
Exit Modes 27
Exit Modes Programming 27
Review Logs 28
Panel Log 28

3
Enforcer V10 Programming Guide
Access Log 28
Reviewing Logs 28
Engineer Tests 28
Walk Test Programming 30
Soak Control Programming 30
Test Siren, Battery Load Test and Outputs 30
Test Communications 31
Diagnostics 31
Wireless Devices 31
View Inputs 31
Signal Strength 31
Battery Status 32
Wireless Dual Frequency Menu 32
Wired Devices 32
View Inputs 32
View PSUs 32
Communications 33
Wireless Device Diagnostics 34
Wired Device Diagnostics 35
Communications Diagnostics 35
Engineer Reset Options 35
Engineer Reset Options Programming 36
Alarm Response 36
Alarm Responses Programming 37
Set Up Downloading 37
Set Up Downloading via Cloud 37
Connecting to the InSite software: 38
Set Up Downloading via RS232 38
Connecting to the InSite software: 38
Software Revision 39
Clean Start 39
Clean Start Programming 40
Appendix A. Defaults 41
Appendix B. Input Types 47
Appendix C. Timers 48
Appendix D. Output Types 50
Appendix E. Fault Finding 53
Wireless Fault Displays 53
RS-485 Bus Problems 54
Power Supply Problems 54
Detection Faults 55
Communication Faults 55

4Enforcer V10 Programming Guide
DEFAULT CODES
Access Codes
User Code: ‘Blank’
Master Manager Code: 2222.
Engineer: 1111
Clean Start Codes
Clean start with the code ‘2000’ (UNGRADED)
Clean start with the code ‘2020’ (Grade 2)
Other Codes
Keypad Security Code: ‘2000’
Delete All Wireless Data: ‘2000’
TECHNICAL SUPPORT
If you are still experiencing issues with the installation, please call our UK technical support team.
Please note: In order to get your issue resolved quickly, please have the software revision of the panel
ready to give to one of our engineers.
Alternatively if you do not require assistance straight away, you can email the team who will reply to you as soon
as possible.
Our oce hours are: Monday to Friday 8:00 - 18:30.
*
0333 444 1280
([email protected]

5
Enforcer V10 Programming Guide
THE ENGINEER MENU
The Engineer Menu must be accessed in order to program all system congurations.
Please note
1. All tamper alarms (including case tamper), will be disabled once in the Engineer Menu.
2. All personal attack and re alarms will not cause an alarm in the Engineer Menu.
Accessing The Engineer Menu
Access to the Engineer Menu will be allowed if the Enforcer is unset. If set, the Enforcer must be unset rst via a valid
user code/tag/keyfob in order to gain access. If the ‘Allow Engineer Menu’function in the Master Manager Menu is
set as ‘No’, the message ‘Authorisation Required’ will be shown and access will be denied until this option is set as
‘ Ye s ’.
1. Enter the engineer code (default 1111).
2. If any faults that are active, they will be displayed now on the screen. Press Aand enter the engineer
code again.
3. ‘SET DATE & TIME’is displayed.
4. Engineers Menu has been accessed.
When the Engineer Menu is accessed, a high pitch tone is generated intermittently.
Please note: It is essential that a factory default (clean start) is performed after initial power up to
ensure that the correct defaults have been chosen.
Exiting The Engineer Menu
When a Main Menu Item (a menu that is in capital letters) is displayed, press or scroll to‘EXIT ENGINEERS MENU?’
and press .
Useful Menu Options
Wireless device control
Learns and deletes all wireless inputs, bells and arming stations. To learn wireless keyfobs enter the Master Manager
menu and scroll to CHANGE CODES. (Refer to the user manual).
Change inputs
Programs all input types, attributes, areas and names and on the Enforcer.
Assign keypads and readers
Assigns wired/wireless keypads and readers, and enables readers for entry control.
Please note: Keypads and Readers must be addressed at the device and at the keypad.

6Enforcer V10 Programming Guide
Codes and users
Changes the ‘Engineer code’, ‘Master Manager code’ and ‘Duress codes’. To change user codes enter the Master
Manager menu and scroll to ‘EDIT USERS’.
Change outputs
Programs any outputs and assigns output modules to the Enforcer.
Diagnostics
Displays power, input status, wireless arming stations, wireless signal strength and wireless battery levels.
Communications
Enables a modem (if connected), allows signalling via communication formats or SMS, and enables the ProControl+
App and Cloud. Please refer to the ‘Communications Guide’.
GENERAL INFORMATION
Default Codes
User: ‘Blank’
Master Manager: 2222
Engineers: 1111
Initial Power Up
Power up the Enforcer system, an alarm will be generated. Proceed to the Enforcer keypad, which will display (from
power up):
1. Once power has been applied to the Enforcer, ‘Please Wait’ will be displayed, followed by ‘485 Comms Lost’.
After approximately one minute, the Enforcer will the time on the display, indicating the system is ready to
use.
2. The Enforcer is defaulted to keypad address ‘0’.
Testing The Keypad
With the system unset, press the key for 5 seconds at any keypad. This will cause all the LEDs on that keypad to
illuminate, and the LCD screen to display each pixel. The keypad will revert to normal display after the test which
will last about 10 seconds.
Wired Keypads/Readers

7
Enforcer V10 Programming Guide
Keypads
Three additional wired keypads may also be connected to the Enforcer.
Key functions
= Exit Engineer and Manager menu / Selects Area A.
= Moves backwards to the previous menu item / Selects Area B.
c= Enables chime and displays additional information in the log / Scrolls back‘one’ in a sub menu / Selects Area
C.
D= Moves forward in the log / scrolls between options and enters the master manager menu /Selects Area D.
fp= Not used. []= Directional buttons.
I= Selects items and enters menus.
A= Cancels items, resets the panel and moves to next item in a menu item.
Please note
1. If any additional keypads are installed on the Enforcer, it is possible to access the Engineer Menu on
any keypad. For example, if the Engineer menu is accessed on keypad address 0, the other keypads
will display ‘System Busy’. To access the Engineer menu on any other keypad, press the key on the
relevant keypad and the Engineer menu will be displayed.
2. A wireless keypad can be connected to set/unset (LEDRKP-WE)
The Internal Tag Reader (EUR-107)
The Internal tag reader can be used for setting/unsetting, entry control or access control. Refer to the installation
manual for all connections.
Tag Area (Where a valid tag must be presented to set/unset)
Alert LED
Alarm LED
Tamper LED
Fault LED
Unset LED
The External Tag Reader (EUR-108)
The Internal Tag Reader can be used for setting/unsetting, entry control or access control. Refer to the installation
manual for all connections.
To set/unset the system using the External Tag Reader, present a pre-programmed tag to the
centre of the prox.
The prox will display the system status: Green = Unset. Red = Set. Present the tag again
within 10 seconds to set and unset the system.
Please note: The system will set depending on the type of exit mode programmed
(Final door, Timed or Push to set)

8Enforcer V10 Programming Guide
Text Programming
Text may be programmed for input names, for the ‘sign-on’ message, and to
identify the Level or Area. Each key is allocated alpha-numeric or punctuation
marks characters as shown left:
The Enforcer incorporates predictive text, so the system will predict which word
is being spelt. For example, if ‘B’ is entered, followed by ‘e’then ‘d’, Bedroom will
be displayed. To accept, press . If the word that is required doesn’t appear
on the LCD display, type in the next letter and so forth until complete.
To type a word, press the relevant key the appropriate number of times – e.g.
for the letter‘k’ press twice, or for the letter ‘s’ press four times.
For punctuation marks, press the key.
In addition, the keys are used as follows:
= make the character into a capital
= move cursor left
= clears cursor / adds a space
= moves cursor right
Engineer Function: Set System
Setting and unsetting the system can be done using the Engineer code.
1. Press .
2. Enter the Engineer code (default 1111).
3. Press if any faults appear.
4. ‘SET SYSTEM’ is displayed.
5. Press 
6. Select the areas to set. Press 
7. The setting period will begin.
8. Once the timer expires, and a beep is heard, the Enforcer is set.
9. To unset, enter the Engineer code again.
Engineer Function: Forced Arm On Inputs
The ‘Force Arm On Inputs’ function enables two nominated inputs on the Enforcer to be set. Either input can be
triggered to allow real life signalling or alarm testing. This function is useful when a building is full of people and
these tests are needed.
Please note
1. The system will give the correct signalling response to the Setting, and any resulting alarm.
2. If the system has been set by any other code, the Engineer code will not unset it.

9
Enforcer V10 Programming Guide
1. Press 
2. Enter the Engineer code (default 1111).
3. Press if any faults appear.
4. ‘SET SYSTEM’ is displayed.
5. Press 
6. ‘FORCE ARM ON 1st INPUT’ is displayed.
7. Enter the 1st input that is to be active. Press 
8. Enter the 2nd input that is to be active. Press 
9. Select the areas to set. Press 
10. The setting period will begin
11. Once the timer expires, and a beep is heard, the Enforcer is set and the 2
inputs chosen will be active.
12. To unset, enter the Engineer code again.
THE ENGINEER MENU
Any programming is only saved when exiting the Engineer menu. It is essential that a ‘CLEAN START’ is performed
after initial power up.
SET DATE & TIME
All log entries are date and time stamped. This can also programmed in the Master Manager Mode. The time is also
shown on the LCD in ‘Day Mode’.
Please note: Please note that powering down the system will reset the time and date information.
Year, Month, Day, Hours, and Minutes
Enter the year, month, day, hours and minutes.
DST Adjust
Enable or disable the ‘Day Light Saver Time Adjust’ as required.
Set Date and Time Programming
Press or to scroll to ‘SET DATE AND TIME’. Press .
‘Year’ will be displayed. Enter the year and press . Repeat for Month, Day, Hours
and Minutes and press .
‘DST Adjust’ will be displayed. Press [or ]to enable or disable the function
and press .

10 Enforcer V10 Programming Guide
WIRELESS DEVICE CONTROL
The Enforcer supports a maximum of 32 wireless inputs, 32 wireless keyfobs, 2 wireless Deltabell external sounders
and 4 wireless arming stations.
Please note: This is without any expanders tted to the system
Control Inputs
‘Control Inputs’learns and deletes wireless inputs (detectors, contacts, sensors etc).
Control Bells
‘Control Bells’ learns and deletes wireless Deltabell external sounders.
Programming Keyfob Buttons
‘Program Keyfob Buttons’assigns actions to each buttons on the keyfob.
[0] No action: Disables the button.
[2] Set Area: Sets the chosen area.
[4] Operate Output:Triggers an output (programmable)
when the nominated button is pressed.
[1] Show Status: GREEN = Unset. RED = Set.
[3] Unset Area: Unsets the chosen area.
[6] Personal attack: Activates a personal attack
activation (programmed in Engineers only)
Please note: Keyfobs are learnt in the Master Manager Menu in the function ‘EDIT USERS’.
Control Arming Stations
‘Control Arming Stations’ learns and deletes wireless arming stations. These are use to set/unset the system and
trigger outputs.
Learning Inputs
1. Press or to scroll to ‘WIRELESS DEVICE CONTROL’. Press 
2. ‘Control Inputs’will be displayed. Press .
3. ‘Learn Devices’will be displayed. Press or press to access the delete
menus (you can either delete individual devices or delete all).
4. Press [or ]to select the input (1-32) to learn and press .
5. Open the wireless device then press and hold the‘LEARN’button until all LEDs
ash then release.

11
Enforcer V10 Programming Guide
Please note
1. The learn process is the same on all wireless peripherals. Once the green
LED ashes, the learn process has been successful. If the red LED ashes,
repeat the process above as the learn procedure has not been successful.
2. For full installation instructions please refer to the installation guide
provided with each device.
Learning Bells
1. Press or to scroll to ‘WIRELESS DEVICE CONTROL’. Press .
2. ‘Control Inputs’will be displayed. Press .
3. ‘Control Bells’ will be displayed. Press .
4. ‘Learn Devices’will be displayed. Press or press to access the delete
menus (you can either delete individual devices or delete all).
5. Press [or ]to select the bell (1 or 2) to learn and press .
6. Open the wireless external siren then press and hold the ‘LEARN’ button until
all LEDs ash then release.
Please note: Once the green LED ashes, the learn process has been successful. If the red LED ashes,
repeat the process above as the learn procedure has not been successful.

12 Enforcer V10 Programming Guide
Program Keyfob Buttons
1. Press or to scroll to ‘WIRELESS DEVICE CONTROL’. Press .
2. ‘Control Inputs’will be displayed. Press .
3. ‘Control Bells’ will be displayed. Press .
4. ‘Control Arming Stations’will be displayed, press .
5. ‘Program Keyfob Buttons’will be displayed. Press .
6. Press [or ]to select the user (1-80) and press .
7. Press [or ]to select the button to be programmed and press .
8. Press [or ]to select the action of the button and press .
9. Select the area that the keyfob should be programmed in, press .
Panic alarm (function option 6) must be allocated to two buttons
pressed together ( I + II recommended, button option 6) and can only be
programmed in the Engineer Menu.
Please note
1. Keyfobs are learnt in the Master Manager Menu under ‘EDIT USERS’.
2. Using the output types 170-199 (User Dened), outputs can be activated by the keyfob buttons. Refer
to ‘User Outputs’ function in the ‘CHANGE OUTPUTS’ menu.
Control Arming Stations
1. Press or to scroll to ‘WIRELESS DEVICE CONTROL’. Press .
2. ‘Control Inputs’will be displayed. Press .
3. ‘Control Bells’ will be displayed. Press .
4. ‘Control Arming Stations’will be displayed. Press .
5. ‘Learn Devices’will be displayed. Press  to learn an arming station or press
to access the delete menus (you can either delete individual devices or
delete all).
6. Press [or ]to select which keypad (1-4) to
learn and press .
7. Open the Arming Station and press and hold
the ‘LEARN’ button until all LEDs ash and then
release.
Please note
1. Once the green LED ashes, the learn process has been successful. If the red LED ashes, repeat the
process above as the learn procedure has not been successful.
2. Tags to control setting/unsetting are learnt in the Master Manager Menu under ‘EDIT USERS’.

13
Enforcer V10 Programming Guide
Wireless Arming Station functions are programmed in the ‘ASSIGN KEYPADS/READERS menu and are mapped as:
Arming Station #1 : Address [4] Arming Station #2 : Address [5]
Arming Station #3 : Address [6] Arming Station #4 : Address [7]
CHANGE INPUTS
A total of 66 inputs can be programmed on the Enforcer system. All inputs are unused by default. To save any
programming the Engineer menu must be exited.
Input Types
See Appendix B for all input type options.
Most commonly used input types:
[06] Intruder. [07] Final Exit. [08] Entry Route. [13] Day Alarm.
Please note
1. If an alarm is triggered from an Entry Route input, it will store for 2 seconds before an alarm is
activated. If a Final Exit input is triggered within this time, the system will select entry time, rather than
an intruder alarm.
2. Inputs may be automatically omitted at the time of reinstatement, which is at the end of conrmation
time. This is irrelevant of whether the input has the attribute ‘Ommitable’ set to‘Yes’or ‘No’
Input Areas
The Enforcer supports up to four areas and can be used as follows:
Area A: All Factory
Area B: Reception Only
Area C: Oces Only
Area D: Factory Floor Only
Input Area (Any/All)
In some installations a ‘common’area may be required. A common area is an area that only sets when other specic
areas become set. Example: An entry and exit reception area in a building may only need to be set if both the oces
and warehouse are set. If the oce in Area A is set, but the warehouse in Area B is still occupied, then the reception
would still need to be inactive so people would be able to leave the premises via the entry / exit reception route.
One input can be allocated to one or more areas. In this example the inputs located in the reception area will be
programmed so that the reception inputs will be in Area A and Area B, so these inputs must have the Input Areas
set as ‘ALL’ programmed.
Area A: Oce - Inputs = 3, 4, 5 Area B: Warehouse - Inputs = 6, 7, 8
Reception inputs – 1 and 2 are programmed into both Areas A and B, with both inputs congured as ‘ALL’. The
Reception Area inputs will now only become active if both Area A and Area B are both set.
Please note: All inputs in a common area must be programmed as ‘Entry Route’or ‘Final Exit’.

14 Enforcer V10 Programming Guide
Input Attributes
Chime
The internal sounder of the Enforcer will sound a chime if enabled. Single: Chimes once when the input is triggered.
Follow: Chimes when the input is triggered and only stops once the input is inactive. To enable/disable the chime
in day mode press , when a‘c’ is displayed on the keypad, the chime is enabled.
Omittable
Enables the input to be manually omitted (disabled) from the setting procedure. To omit inputs, there is a function
in the Master Manager menu called ‘OMIT INPUTS’.
Double Knock
The control will only generate an alarm if this input is triggered twice within a pre-set period, or if the input remains
in fault condition for that period.
Normally Open
Enables the system to respond correctly when detectors of ‘normally open’ conguration are wired to the system.
Alternatively converts input types which default to‘normally open’(e.g. Push to set) to operate with normally closed
devices.
Monitor Activity
Enables the input to generate an alarm if the input does not detect any activity for a period specied by the NAT
(Non Activity Time.) See ‘Change Timers’.
Conrm Group
If inputs are selected into the same conrm group, each input will only generate an unconrmed alarm (and will not
generate a conrmed activation). This is useful when two or more shock sensors are being activated by the same
event. If a conrm group is selected as ‘00’, the inputs are not part of any group.
Input Description and Location
A name and location can be entered here. The name will appear on the display if an alarm has occurred; the location
is used for a more detailed reference if required.
Change Inputs Programming
1. Press or to scroll to ‘CHANGE INPUTS’. Press .
2. Press [or ]to select the input to program (01-66). Press .
3. ‘Input Type’will be displayed. Press [or ]to select the input type or input
the shortcut number (see Appendix B, for all input type options.)
4. Press , ‘Input Areas’ will be displayed. Select the areas to be assigned to
the input and press .
5. Input Areas’ will be still be displayed, but this time the options are ‘Any’ or ‘All’.
Make a selection using then [or ]then press .
6. Input Attributes’ will be displayed. If any attributes are needed for the input,
press then press [or ]to select between the attribute enable/
disable options. Finally press to go to the next attribute.

15
Enforcer V10 Programming Guide
7. Input Description’ will be displayed. Press to enter a name and location
for this device or press to return to input selection.
8. Enter Name’will be displayed. Enter the name of the input and press . This
will be displayed if it is activated or when a fault occurs.
9. ‘Enter Location’ will be displayed. Enter the location of the input and press
. This will be displayed if it is activated or when a fault occurs after the
name of the input has been shown.
10. Press [or ]to select another input to program (01-66) or press the 
key to return to the Engineer menu.
CHOOSE MODE
If a Enforcer I/O board or any Zone Expander Module (Input Expander or ZEM) are used, the resistance, EOL mode
and response time of the inputs can be programmed.
Please note: Alarm 4K7, Tamper 2K2 must be selected if wiring double pole to an expander.
EOL Range (End of Line Range)
EOL Range
Programs the panel to operate with dierent resistor values
[0] Alarm: 1K, Tamper: 1K. [1] Alarm: 4K7, Tamper: 2K2.
[2] Alarm: 4K7, Tamper: 4K7. [2] Wide range.
EOL Mode
EOL Mode programs all input expanders to operate as:
[0] Single End of Line (SEOL). [1] Double End of Line (DEOL).
Input Response Time
Input Response time programs the time that an input trigger must be present before the Enforcer system generates
an alarm.
[01] - [30] = 100ms to 3000ms
Please note: Settings above (>) 400ms do not comply with PD 6662 / EN 50131.
Choose Mode Programming
1. Press or to scroll to ‘CHOOSE MODE’. Press .
2. Press [or ]to select the ‘EOL Range’ for all wired inputs*. Press .
3. Press [or ]to select the ‘EOL Mode’for all wired inputs*. Press .
4. Press [or ]to select the ‘Input Response Time’for all wired inputs*. Press
to return to the Engineer Menu.
*On the I/O board and the expanders

16 Enforcer V10 Programming Guide
INSTALL ZEMS
The Enforcer supports up to 66 inputs. Zone Expander Modules (ZEMS) can be used to expand the Enforcer to have
a further 32 wireless inputs, 32 wired inputs or a combination of both. There are also 2 inputs that can be used on
an I/O Board if connected (refer to installation manual).
ZEM Address
[0] ZEM Address 0 (Inputs 35-42)
[2] ZEM Address 2 (Inputs 51-58)
[1] ZEM Address 1 (Inputs 43-50)
[3] ZEM Address 3 (Inputs 59-66)
Please note: Inputs 33 and 34 are taken from the I/O board, these do not need to be addressed.
ZEM Installed
[0] No
[2] EURO-ZEM32-WE
[1] ZEM8/EURO37R
Enter Location
The text entered here will be displayed on the LCD display if a fault occurs on the ZEM, so the ZEM can be easily
located or referenced. For example, the location text maybe “ZEM Kitchen”, “ZEM Loft” etc.
Install ZEMS Programming
1. Press or to scroll to ‘INSTALL ZEMS’. Press .
2. Press [or ]to select the ‘ZEM Address’. Press .
3. Press [or ]to select the ‘ZEM8 or ZEM32-WE’ or No’ to ‘ZEM Installed’.
Press .
4. Enter the location of the ZEM. This is so it is referenced and will appear on the
display if a fault occurs. Press to return to ZEM addressing.
5. Press to return to the Engineers menu.
CHANGE OUTPUTS
This function programs all output types, Any output type may be programmed to any of the systems outputs,
including any outputs for wireless bells. Outputs must be used within their rated capacity. Please see the installation
manual.
Common output types
Refer to Appendix D, for all output type options. Most commonly used input types are:
[0003] Intruder Any
[0018] Unconrmed Any
[0006] Conrmed Any
[0051] Line Fault
[0014] Siren Any
[0052] Mains Fail
[0016] Strobe Any
[1###] Follow Input

17
Enforcer V10 Programming Guide
Endstation Outputs
This function programs the Bell, Strobe and PGM output on the I/O board if connected.
ZEM Outputs
If a zone expander with additional outputs has been connected to the Enforcer, this function programs the outputs
on each expander. The address of the expander is required before the output programming.
Wireless Bells
At default, any wireless bells learnt to the Enforcer have the two outputs programmed as‘Siren Any’and‘Strobe Any’.
These outputs can be programmed dierently if required.
Output Module Outputs
If an output expander is connected to the Enforcer, it must be addressed in this function. All output programming
is also done here. A maximum of 1 output expander can be connected to the Enforcer.
Change Output Programming
1. Press or to scroll to ‘CHANGE OUTPUTS’. Press .
2. ‘Endstation Outputs’ will be displayed. Press to program any outputs on
the I/O module, or press for the next function. Use [or ]to scroll
through the outputs or the select the shortcut number.
3. ‘ZEM Outputs’ will be displayed. Press to program any outputs on the
zone expander, or press for the next function.
4. ‘Wireless Bells’’ will be displayed. Press to program any wireless output
types or press for the next function.
5. ‘Output Module Outputs’’ will be displayed. Press to address an output
module or press for the next function.
6. ‘Keypad Outputs’will be displayed. Press to program any outputs on any
additional keypads connected or press for the next function.
7. ‘Reader Outputs’ will be displayed. Press to program any outputs on any
readers connected or press for the next function.
8. ‘User Outputs’ will be displayed. User Outputs can be activated from the
Master Manager Menu, and can also be programmed to be operated via a
keyfob. If required, this is programmed in‘Program Keyfob Buttons’, sub-menu
‘WIRELESS DEVICE CONTROL’ and program a button(s) for types 170-199.
ASSIGN KEYPADS/READERS
Any additional keypads or readers must be addressed correctly before enabling them in this function. The Enforcer
keypad is automatically addressed as 0 on initial power up. Refer to installation manual for more information.
Address
Up to 3 additional wired keypads or readers and 4 wireless arming stations can also be installed. Address 0 is used
for the Enforcer on-board keypad.

18 Enforcer V10 Programming Guide
Please note: Each keypad has its own individual menu that programs the key-click volume, tag volume
and master volume. It will address a keypad, show the status of the keypad inputs (if programmed),
force the backlight on or o and the identication number of a tag (once a tag is presented). The PA/Fire
timer can be programmed. This menu also addresses the keypad.
To enter the keypad menu, press and hold the key until ‘SECURITY CODE’ is displayed, and then enter ‘2000’.
This function is also used to address the keypad.
Please note: Wireless arming stations are learnt to one the 4 wireless arming station allocations on the
Enforcer. However, are seen as addresses 4-7 in‘Assign Keypads and Readers’
Type
[0] Keypad [1] Reader [2] Not Used.
Reader is
If a reader is installed, the following options can be assigned to the reader:
[0] Set Point: Reader used for setting and unsetting.
[1] Not Used: Reader disabled
[2] Access Control: If an access control system is installed then the reader must be programmed as this type. The
lock open time and door open time can be programmed (in seconds).
[3] Unset Only: If the Reader is to be used as an unset device only, select this type.
[4] Entry Control: Used to lock/unlock doors. The external or internal reader can have magnetic locks connected to
them. This option is used in conjunction with ‘tag opens doors’ in ‘SITE OPTIONS’ page: 18. The lock open time and
door open time can be programmed (in seconds).
Set point sets
A ‘Set Point’ means that you can program the keypad/reader to set certain areas only, and is used in conjunction
with the areas allocated to a user code.
For example, if a user code is programmed to operate areas ‘A’and ‘B’, but the keypad/reader is only programmed to
set area ‘A’, then the system will set only area‘A’.
Selects the area that the device will be defaulted to.
Set point unsets
An ‘Unset Point’ means that you can program the keypad/reader to unset certain areas only. This is used in
conjunction with the areas allocated to a user code.
For example, if a user code is programmed to operate areas ‘A’and ‘B’, but the keypad/reader is only programmed to
Unset area ‘A’, then the system will unset area‘A’ only.
Set point in
The keypad needs to also be told which Areas it is operating “in”. For example, a keypad may only be needed to
operate in Area A, but other code users may use the keypad to quick set other Areas (such as a cleaner, director,
caretaker etc). Therefore if Areas A and B are selected in the previous options (Arm point sets and unset), but Area
A only is selected in ‘Set point in’, then Area B will quick arm once a valid tag/code has been entered. To program
Areas operating with their programmed timer, then the Areas need to be entered into the“Set Point In”function.
Set point description
A name and location can be entered here. The name will appear on the display if an alarm has occurred, the location
is used for a more detailed reference if required. E.g. Name = Entrance Keypad. Location = Hall

19
Enforcer V10 Programming Guide
Programming Keypads
1. Press or  to scroll to ‘ASSIGN KEYPADS/READERS’. Press .
2. Press [or ]to select the address. Press .
3. ‘Type’ will be displayed. Press 0to select keypad. Press 
4. ‘Set Point Sets’will be displayed. Select the area(s). Press . Set Point Unsets’
will be displayed. Select the area(s). Press . ‘Set Point In’ will be displayed.
Select the area(s). Press .
5. ‘Set Point Description’ will be displayed. Press to enter the name and
location if required.
6. ‘Enter Name’ will be displayed. Enter the name of the keypad and press .
7. ‘Enter Location’ will be displayed. Enter the location of the keypad and press
.
8. Press [or ]to select another device address to program (0-3) or press
the key to return to the Engineer menu
Programming Readers
Set Point or Unset Only
1. Press or to scroll to ‘ASSIGN KEYPADS/READERS’. Press .
2. Press [or ]to select the address. Press .
3. ‘Type’ will be displayed. Press to select reader. Press .
4. ‘Reader is’ will be displayed. Press 0for ‘Set Point’ or press for ‘Unset
Only’ Press .
5. ‘Set Point Sets’will be displayed. Select the area(s). Press . Set Point Unsets’
will be displayed. Select the area(s). Press . ‘Set Point In’ will be displayed.
Select the area(s). Press .
6. ‘Set Point Description’ will be displayed. Press to enter the name and
location if required.
7. ‘Enter Name’ will be displayed. Enter the name of the keypad and press .
8. ‘Enter Location’ will be displayed. Enter the location of the keypad and press
.
9. Press [or ]to select another device address to program (0-3) or press
the key to return to the Engineer menu.

20 Enforcer V10 Programming Guide
Entry Control or Access Control
1. Press or to scroll to ‘ASSIGN KEYPADS/READERS’. Press .
2. Press [or ]to select the address. Press .
3. ‘Type’ will be displayed. Press to select the reader. Press .
4. ‘Reader is’ will be displayed. Press 2for ‘Access Control’ or press 4 for ‘Entry
Control’ Press .
5. ‘Set Point Sets’will be displayed. Select the area(s). Press . Set Point Unsets’
will be displayed. Select the area(s). Press . ‘Set Point In’ will be displayed.
Select the area(s). Press .
6. ‘Lock Open Time’will be displayed. Enter the Lock Open Time in seconds and
press . (Max 255 seconds).
7. ‘Door Open Time’will be displayed. Enter the Door Open Time in seconds and
press . (Max 255 seconds).
8. ‘Access Control Description’will be displayed. Press .
9. ‘Enter Name’ will be displayed. Enter the name of the keypad and press .
10. ‘Enter Location’ will be displayed. Enter the location of the keypad and press
.
11. Press [or ]to select another device address to program (0-3) or press
the key to return to the Engineer menu.
Wireless Arming Station Options
Tag Read Enable
Enables the proximity tag reader on the wireless arming station.
Auto Wakeup
Forces the keypad to automatically wake up when an entry time is initiated.
Supervision
When switched to ‘Yes’the control panel will supervise the signal of the wireless arming station.
Back Light
Toggles the LCD backlight on or o.
Entry/Exit Sound
When enabled, the arming station will mimic the entry/exit tones of the panel.
Set Point Sets
Enter the areas that the arming station is permitted to set.
Set Points Unsets
Enter the areas that the arming station is permitted to unset.