HIK VISION DS-19A08-F/Kx User manual

Control Panel User Manual
1
UD.6L0206D1044A02
Network Security Control Panel
User Manual

Control Panel User Manual
2
User Manual
COPYRIGHT © 2015 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Control Panel
The Manual includes instructions for using and managing the product. Pictures, charts, images and all
other information hereinafter are for description and explanation only. The information contained in
the Manual is subject to change, without notice, due to firmware updates or other reasons. Please
find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE
OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT
YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

Control Panel User Manual
3
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
0100001050519

Control Panel User Manual
4
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired
operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Control Panel User Manual
5
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to prevent
serious injury or death.
Cautions Follow these precautions to prevent
potential injury or material damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard.
The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may cause
over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used product to rain or
moisture.
This installation should be made by a qualified service person and should conform to all the local
codes.
Please install blackouts equipment into the power supply circuit for convenient supply
interruption.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the product yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
Please do not look directly into the laser light within 6 meters because laser is hazardous to
humans.

Control Panel User Manual
6
Cautions:
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product on vibratory
surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The strong light can
cause fatal damage to the product.
The sensor may be burned out by a laser beam, so when any laser equipment is being used,
make sure that the surface of the sensor not be exposed to the laser beam.
For working temperature, please refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
While shipping, the product should be packed in its original packing.
Please use the provided glove when open up the product cover. Do not touch the product cover
with fingers directly, because the acidic sweat of the fingers may erode the surface coating of the
product cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the product cover. Do
not use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion. Please use the
manufacturer recommended battery type.

7
Content
Chapter 1 Introduction ______________________________________________10
1.1 Overview _________________________________________________________ 10
1.2 Feature ___________________________________________________________ 10
Chapter 2 Installation and Wiring _____________________________________10
2.1 Main Board Overview _______________________________________________ 13
2.2 Device Wiring ______________________________________________________ 14
2.2.1 Detector Wiring _______________________________________________________ 14
2.2.2 Alarm Output Wiring ___________________________________________________ 16
2.2.3 Keypad Wiring_________________________________________________________ 16
2.3 System Start-up ____________________________________________________ 17
2.3.1 Control Panel Start-up __________________________________________________ 17
2.3.2 Alarm Keypad Start-up __________________________________________________ 17
2.3.3 Keypad Address _______________________________________________________ 20
2.3.4 Factory Settings _______________________________________________________ 20
2.3.5 Activating the Control Panel______________________________________________ 21
Chapter 3 Keypad Operation (Local Operation ） _________________________27
3.1 Alarm Keypad Configuration __________________________________________ 27
3.1.1 Installer Password Settings_______________________________________________ 27
3.1.2 Operator Configuration _________________________________________________ 28
3.1.3 Zone Parameters Configuration ___________________________________________ 29
3.1.4 Telco Line Communication Control ________________________________________ 33
3.1.5 Dialing Account Configuration ____________________________________________ 34
3.1.6 Alarm Receiver Phone Number Settings ____________________________________ 35
3.1.7 Zone Associated Trigger Configuration _____________________________________ 36
3.1.8 Trigger Event Linkage Configuration _______________________________________ 36
3.1.9 Trigger Time Settings ___________________________________________________ 38
3.1.10 Siren Configuration_____________________________________________________ 39
3.1.11 Control Panel Time Settings ______________________________________________ 39
3.1.12 Control Panel IP Configuration____________________________________________ 40
Local Port Number Configuration _________________________________________________ 40
3.1.13 Subnet Mask Configuration ______________________________________________ 41
3.1.14 Gateway Configuration__________________________________________________ 41
3.1.15 GPRS Configuration ____________________________________________________ 42
3.1.16 SIM Card No. Configuration ______________________________________________ 42
3.1.17 Uploading Center IP Configuration ________________________________________ 43
3.1.18 Uploading Center Port Configuration ______________________________________ 44
3.1.19 Center Protocol and Account Configuration _________________________________ 44

Control Panel User Manual
8
3.1.20 Siren Linked Event Configuration __________________________________________ 45
3.1.21 Emergency Alarm Linkage Configuration____________________________________ 46
3.1.22 Control Panel Tampering Alarm Configuration _______________________________ 47
3.1.23 Testing Report Configuration _____________________________________________ 47
3.1.24 Partition Configuration__________________________________________________ 49
3.1.25 Public Partition Settings _________________________________________________ 55
3.1.26 Fault Detection Configuration ____________________________________________ 55
3.1.27 Center Group Configuration______________________________________________ 59
3.1.28 Whitelist Parameters Configuration________________________________________ 63
3.1.29 Schedule Configuration _________________________________________________ 69
3.1.30 Wireless User Permission Configuration ____________________________________ 77
3.2 Keypad Alarm Operation Code ________________________________________ 78
3.2.1 Device Initialization ____________________________________________________ 78
3.2.2 Control panel Arming and Disarm _________________________________________ 78
3.2.3 Stay Arming___________________________________________________________ 79
3.2.4 Zone Bypass/Recovery __________________________________________________ 79
3.2.5 Group Bypass _________________________________________________________ 79
3.2.6 Group Bypass Recovery _________________________________________________ 80
3.2.7 Keypad Cancel Alarm ___________________________________________________ 80
3.2.8 Alarm Output Operation ________________________________________________ 80
3.2.9 Emergency Alarm ______________________________________________________ 80
3.2.10 System Status Query____________________________________________________ 81
3.2.11 Control Panel and Wireless Device Connection ______________________________ 81
3.2.12 Deleting the Specified Connected Wireless Device____________________________ 81
3.2.13 Deleting all the Connected Wireless Device _________________________________ 82
3.2.14 Main Operator Password Changing ________________________________________ 82
3.2.15 Control Programming Operation __________________________________________ 82
3.2.16 Entering Partition ______________________________________________________ 82
3.2.17 Alarm Center Test ______________________________________________________ 83
3.2.18 Project Mode _________________________________________________________ 83
3.2.19 Enabling/Disabling Key Tone _____________________________________________ 83
3.2.20 LCD Backlight Control ___________________________________________________ 83
3.2.21 LCD Backlight off_______________________________________________________ 84
3.2.22 Pacing _______________________________________________________________ 84
3.2.23 SMS Arming/Disarming _________________________________________________ 84
3.2.24 Control Panel Soft Recovery ______________________________________________ 85
3.2.25 Current Fault Tone Disabling _____________________________________________ 85
3.2.26 Test Report Manually Triggering __________________________________________ 85
3.2.27 Keypad Locking and Unlocking____________________________________________ 85
3.2.28 Exiting the Operation ___________________________________________________ 85
3.3 System Status Display Demonstration___________________________________ 86
Chapter 4 Accessing by Client Software ________________________________90

Control Panel User Manual
9
4.1 Installing the iVMS-4200 _____________________________________________ 90
4.2 User Registration and Login ___________________________________________ 94
4.3 Network Security Control Panel Settings ________________________________ 95
4.3.1 Add/Edit/Delete the Device ______________________________________________ 95
4.4 Remote Configuration _______________________________________________ 96
4.4.2 System Information Configuration_________________________________________ 97
4.4.3 Network Configuration_________________________________________________ 103
4.4.4 Alarm Configuration ___________________________________________________ 112
4.5 Fault Handling ____________________________________________________ 127
4.6 Operation ________________________________________________________ 128
4.7 Status ___________________________________________________________ 129
Chapter 5 Trouble Shooting _________________________________________131
Appendix1 ： Specifications ___________________________________________142
Appendix2 ： CID Report ______________________________________________143
Appendix3 ： LED Keypad Prompt Sound _________________________________146
Appendix4 ： Conversion Table_________________________________________146

Control Panel User Manual
10
Chapter 1 Introduction
1.1 Overview
The DS-19A08-F/Kx(G) is a commercial control panel with 8 partitions supported.
The panel uses embedded microcontroller technology for zones monitoring and
system status detection. The alarm or status reports can be transmitted to the
central alarm monitoring station through programming. An integrated master
keypad with the LED/LCD display is designed for implementing a readable
programming progress. Multiple alarm types and report transmission methods
(telephone network, the Ethernet network and the GPRS wireless network) are
supported for the panel. A mobile client is attached for remote control such as
pushing notifications of the alarm or status reports and remote arming/ disarming.
The control panel is mainly deployed in the security system of shopping malls,
stores, residences, apartments, communities and so on.
1.2 Feature
Hardwire Zones and Relay Outputs
8 hardwire zones;
Tamper supervision on the hardwire zones;
1 channel of relay output;

Control Panel User Manual
11
Up to 8 channel extension relay outputs;
Relay outputs can be triggered by alarm events or system events;
Partitioning
8 partitions, which can be controlled independently;
1 common partition (No.1 partition), that can be programmed to be linked with
any other two partitions;
Event Log *
Provides a Contact ID report cache that can store up to 250 reports;
Up to 8000 alarm event logs, 2000 operation events logs and 1500 management
event logs can be stored with time tag;
Support event logs tracing over the Ethernet System Communication;
GPRS communication and Short Message Service (SMS) (DS-19A08-
F/KxG only);
ADEMCO Contact ID communication over the telephone network;
Encrypted NAL2300 communication over the Ethernet and the GPRS wireless
network;
HIK-SDK communication over the Ethernet network;
Report Strategy
Support up to 2 independent central stations over the phone lines;
Support up to 2 independent central stations over the Ethernet network;
Support up to 2 independent central stations over the GPRS wireless network;
Support up to 6 independent report channel groups consisted of one main
channel and 3 backup channels each, that can transmit reports in parallel;
Each report channel can be configured to transmit reports to the central alarm
monitoring station over the telephone, Ethernet or GPRS wireless network;
Report can be pushed to a mobile phone with mobile client;
Report message can be transmitted to the mobile users with a bound phone
number (SIM card);
Supports 6 communication channels over the Ethernet network base on the
HIK-SDK protocol;
Remote Control
Up to 32 key fobs for radio transmitter operations;

Control Panel User Manual
12
Allows remote control operations with mobile client;
Message control operations, such as arming, disarming, and clearing the alarm,
via short messages sent from the bound phone number;
Peripherals Devices
Provides a half-duplex RS-485 device bus, which can interface with keypads and
relay modules;
Up to 8 addressable keypads;
1 external audio output for alarm warning devices, such as sirens, bells or horns
with 12VDC power supply;
User Management
Users are consisted of an Installer, a Master User, 15 keypad operators and 16
network operators;
Authority level management of users assigned different security codes;
Power Supply Management
14VDC power adapter;
Provides a power supply interface with battery sensing hardware to prevent deep
discharging an charge management circuit hardware for the external backup
battery;
Automatically switch between A.C. power supply and backup battery power
supply;
1 auxiliary power output rated max. 14VDC, 750mA;
Supports manually hardware reset to factory defaults;
Additional Features
Integrated master keypad with the LED/LCD display;
Tamper and movement protection function;
Support scheduling operations, such as arming, disarming, and output activating.

Control Panel User Manual
13
Chapter 2 Installation and Wiring
2.1 Main Board Overview

Control Panel User Manual
14
No.
Description
No.
Description
1
Power Adapter
9
Handset Interface
2
Lead-acid Battery
10
Incoming Telco Line
Interface
3
Alarm Bell
11
Alarm Input Interface
4
Alarm Output (Alarm
Lamp)
12
SIM Card/2G Card Slot
5
RS-485 Terminals
13
Buzzer
6
Auxiliary Power Interface
(DC Output）
14
TAMPER Switch
7
RS-485 TERMINATION
Resister
15
RTC CLOCK Button Cell
8
LAN Interface
16
Reset Button
2.2 Device Wiring
2.2.1 Detector Wiring
The alarm input interfaces of the control panel are show as follows.

Control Panel User Manual
15
The wiring of sensor is shown as follows.
2.2KΩ
NC
C
Z
G
Peripheral Security DetectorAlarm Host
Normal Closed Detector
2.2KΩ
NO
C
Z
G
Alarm Host
Normal Opened Detector
Peripheral Security Detector
The Tamper-proof wiring is shown below.
2.2KΩ
2.2KΩ
ZONE
GND
DETECTOR
N.C.
N.O.
TAMPER

Control Panel User Manual
16
2.2.2 Alarm Output Wiring
The alarm output interfaces of the control panel are show as follows.
The wiring of alarm output is shown as follows:
External Device
NO/NC
COM
DC12V
Breaker
External DC Load
External Device
NO/NC
COM
DC12V
Breaker
AC220V
External AC Load
Relay
The DC current supplied by the control panel is used for external devices. The
load current cannot be over 1A.
2.2.3 Keypad Wiring
The keypad wiring is shown as follows.

Control Panel User Manual
17
2.3 System Start-up
For configuring the security control panel, you should restore the system of
the control panel after start-up.
2.3.1 Control Panel Start-up
The keypad registration will be completed in 10 seconds after the control
panel being power on. The system then will complete the start-up and enter
the properly status of working.
2.3.2 Alarm Keypad Start-up
The LED keypad will make continuously prompt tones if the keypad does not
receive the registration respond from the control panel in 20 seconds after it
being power on. While the registration is succeeded, the working status
indicator will turn green.

Control Panel User Manual
18
LED Alarm Keypad Network Indicator
Working Status
Indicator Status
Proper Network
Green (Flickering)
Network Exception
Off
LED Alarm Keypad Status Indicator
Working Status
Indicator Status
System Works Properly
Off
System Exception
Red (Continuously Light)
LED Alarm Keypad Partition Indicator
Working Status
Indicator Status
Single Partition
Off
Multi-partition
Green (Continuously Light)
LED Alarm Keypad Stay Indicator
Working Status
Indicator Status
Stay Arming Disabled
Off
Stay Arming Enabled
Orange (Continuously Light)
LED Alarm Keypad Armed Indicator
Working Status
Indicator Status
Partition Arming
Red (Continuously Light)
Partition Disarming
Green (Continuously Light)
In Programming
Green (Flickering)
Main Operator
Password Editing
Green (Flickering)

Control Panel User Manual
19
Working Status
Indicator Status
Remote Control
Connecting
Green (Flickering)
Pacing Mode
Red (Continuously Light)
LED Alarm Keypad Ready Indicator
Working Status
Indicator Status
Normal
Green (Continuously Light)
In Project
Red (Flickering)
Main Operator
Password Editing
Green (Flickering)
Remote Control
Connecting
Red (Flickering)
In Programming
Green (Flickering)
LED Alarm Keypad Channel Indicator
Working Status
Indicator Status
Normal
Off
Alarm
Red (Flickering)
Exception
Red (Continuously Light)
Bypass
Green (Continuously Light)
LED Alarm Keypad Channel Indicator Status in Project Mode
No.
Description
No.
Description
1
Off-hook
5
Send CID Report
2
Dialing
6
Receive Confirmation
Sound
3
Alarm Connecter
7
Control Panel On-hook

Control Panel User Manual
20
No.
Description
No.
Description
Disconnection
4
Receive Hands-shake
Sound
8
Alarm Connecter On-hook
LED Alarm Keypad Channel Indicator Status in Status Mode
No.
Description
No.
Description
1
AC Power Outages
5
Keypad Disconnection
2
Low Battery for
Accumulator
6
Network Disconnection
3
Control Panel Tampering
Alarm Enabled
7
No SIM Card
4
Telephone Line
Disconnection
8
Reserved
2.3.3 Keypad Address
An address is required for each alarm keypad in the system. These addresses
cannot be repeated. Once exchanging the alarm keypad, the address of the
new keypad must be the same as the replaced one. You should configure the
address via DIP switch of the keypad before powering on the system. The
address should be in the range of 1~31.
2.3.4 Factory Settings
If powering on the system before zone connection, a 2.2k Ohm resistance is
required for bridge connection between each zone.
Password and Report
Installer Password: 012345