HIK VISION DS-3WF01C-2N/O User manual

DS-3WF01C-2N/O User Guide
i
Wireless Bridge DS-3WF01C-2N/O
User Guide

DS-3WF01C-2N/O User Guide
i
User Guide
COPYRIGHT © 2019 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
The Guide includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Guide is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website
(http://overseas.hikvision.com/en/).
Please use this user guide under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.

DS-3WF01C-2N/O User Guide
ii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of
as unsorted municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed
of as unsorted municipal waste in the European Union. See the product documentation
for specific battery information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

DS-3WF01C-2N/O User Guide
iii
Applicable Models
This guide is applicable to DS-3WF01C-2N/O.
Symbol Conventions
The symbols that may be found in this document are defined as follows.
During the installation and utilization of the device, please strictly conform to electrical safety
rules in different nations and regions.
You shall acknowledge that the use of the device with Internet access might be under network
security risks, please strengthen protection for your personal information and data security. If
you find the device might be under network security risks, please contact with us.
Symbol
Description
Provides additional information to emphasize or supplement
important points of the main text.
Indicates a potentially hazardous situation, which if not avoided,
could result in equipment damage, data loss, performance
degradation, or unexpected results.
Indicates a hazard with a high level of risk, which if not avoided, will
result in death or serious injury.

DS-3WF01C-2N/O User Guide
iv
Contents
Chapter 1 Application Scenario..................................................................................................1
1.1 Networking requirement .........................................................................................................1
1.2 Solution ....................................................................................................................................1
1.3 Connecting the wireless bridges..............................................................................................1
1.3.1 Hardware connection of AP device..................................................................................1
1.3.2 Hardware connection of CPE device................................................................................2
1.4 Networking topology ...............................................................................................................3
Chapter 2 Login .........................................................................................................................4
2.1 Logging in to the web UI of the wireless bridge ......................................................................4
2.2 Logging out of the web UI of the wireless bridge....................................................................8
Chapter 3 System Status............................................................................................................9
3.1 Device info ...............................................................................................................................9
3.2 Information of peer device ....................................................................................................10
Chapter 4 Network ..................................................................................................................12
4.1 Overview ................................................................................................................................12
4.2 Changing the IP address.........................................................................................................13
Chapter 5 Wireless ..................................................................................................................15
5.1 Overview ................................................................................................................................15
5.2 Changing wireless parameters...............................................................................................17
5.3 Scanning SSID nearby.............................................................................................................18
Chapter 6 System ....................................................................................................................20
6.1 Maintenance ..........................................................................................................................20
6.1.1 Device info .....................................................................................................................20
6.1.2 Maintenance ..................................................................................................................20
6.1.3 Import/Export ................................................................................................................23
6.1.4 Upgrade..........................................................................................................................24
6.2 Time settings..........................................................................................................................26
6.2.1 Manual ...........................................................................................................................26
6.2.2 Synchronize with the internet .......................................................................................26
6.3 Basic Service...........................................................................................................................27
6.3.1 SSH server ......................................................................................................................27
6.3.2 Export .............................................................................................................................29
6.4 Account ..................................................................................................................................30
Appendix.................................................................................................................................... 31
A Default parameters.....................................................................................................................31
B Acronyms and Abbreviations......................................................................................................32

DS-3WF01C-2N/O User Guide
1
Chapter 1 Application Scenario
1.1 Networking requirement
To ensure the safety of employees and property, a video surveillance system needs to be installed
in a building site.
1.2 Solution
The wireless bridges are used to address this requirement.
1.3 Connecting the wireless bridges
1.3.1 Hardware connection of AP device
Connect the AP device to a switch in monitor center. See the following figure:
AP device
PoE injector
Switch
NVR
Monitor

DS-3WF01C-2N/O User Guide
2
1.3.2 Hardware connection of CPE device
Connect the CPE device to an IP camera in the monitoring site.
CPE device
PoE injector
IP camera

DS-3WF01C-2N/O User Guide
3
1.4 Networking topology
Select one scenario to install the wireless bridge to the corresponding site.
Switch
NVR
Monitor
Monitoring point

DS-3WF01C-2N/O User Guide
4
Chapter 2 Login
2.1 Logging in to the web UI of the wireless bridge
For initial use of the router, refer to the quick start guide of the wireless bridge to activate the
wireless bridge. After activating the wireless bridge, you can refer to the following procedure for
login.
Step 1 Connect a computer to the wireless bridge, or the switch connected to the wireless bridge.
Step 2 Configure the IP address of the computer used to configure the wireless bridge. OS
example: Windows 7
(1) Right-click the icon on the lower right corner of the desktop.
(2) Click Open Network and Sharing Center.
(3) Click Local Area Connection, then click Properties.
1
2

DS-3WF01C-2N/O User Guide
5
(4) Double-click Internet Protocol Version 4 (TCP/IPv4).
(5) Select Use the following IP address, set the IP address to 192.168.1.X(Xranges from 2 to
253, excluding 36), the Subnet mask to 255.255.255.0, and click OK.
(6) Click OK on the Local Area Connection Properties window, and close the other
windows.

DS-3WF01C-2N/O User Guide
6
Step 3 Log in to the web UI of the wireless bridge.
(1) Start a web browser, and visit 192.168.1.36.
If the following page appears, click Advanced.
Then click Proceed to 192.168.1.36 (unsafe).

DS-3WF01C-2N/O User Guide
7
(2) Enter the login password you set before, and click Login.
----End

DS-3WF01C-2N/O User Guide
8
Log in to the web UI successfully. Now you can configure the wireless bridge.
If the login page does not appear, try the following solution:
Check whether the wireless bridge is powered on properly, and the computer is connected to
the wireless bridge properly.
Check whether the IP address of the computer is set to 192.168.1.X(Xranges from 2 to 254,
excluding 36).
Reset the device and refer to the quick start guide to configure it again.
Reset method: After the device is powered on for about 1 minute, hold down the RST button
for about 8 seconds, then release it. When all the LED indicators light up, the device is restored
to factory settings.
2.2 Logging out of the web UI of the wireless bridge
Click the Logout on the upper-right corner of the web UI to logout. When you close the web
browser, the system logs you out as well.

DS-3WF01C-2N/O User Guide
9
Chapter 3 System Status
This module allows you to view the information of this wireless bridge and peer.
3.1 Device info
Log in to the web UI, and choose Status.
You can view the device info, wireless parameters and network parameters here.
Parameters Description
Items
Description
Device Info
Device Name
It specifies the name of this device. If this device is not the only
one of its kind in the network, this name helps you identify the
device. You can change the name of this device on the
System > Maintenance page.
Model
It specifies the model number of this device.
Device SN
It specifies the serial number of this device. The devices in the
same package have the same serial number.
Firmware
It specifies the system software version number of this device.
Uptime
It specifies time during which this device is operating.
MAC Address
It specifies the MAC address of LAN port of this device. When
connecting to another device using an Ethernet cable, the
wireless bridge uses this MAC address to communicate with
the device.
Wireless
Operating Mode
It specifies the working mode the device operates. The wireless

DS-3WF01C-2N/O User Guide
10
Items
Description
Parameters
bridge works in AP mode or CPE mode, and cannot be changed.
SSID
It specifies the wireless network name of this device.
Security Mode
It specifies the security mode of the wireless network of this
device.
Network Mode
It specifies the network mode of this device.
Channel Width
It specifies the bandwidth of the operating channel of a
wireless network.
Channel
It specifies channel in which this device operates, and its center
frequency.
Transmission Power
It specifies the transmit power of this device.
Higher number indicates wider WiFi coverage. Setting a proper
transmit power helps improve the performance and security of
the wireless network.
Network
Parameters
IP Address
It specifies the IP address (also named management IP address)
of this device. You can change this IP address on the Network
page.
Subnet Mask
It specifies the subnet mask of the wireless bridge.
Gateway
It specifies the default gateway of the wireless bridge. When
the device accessing the internet, packets should be forwarded
through the gateway.
DNS1
It specifies the primary DNS server IP address of the wireless
bridge.
DNS2
It specifies the secondary DNS server IP address of the wireless
bridge.
3.2 Information of peer device
Log in to the web UI, and choose Status > Peer Device.
You can view the transmitted and received rate of this wireless bridge, and view the related
information of peer device, such as signal strength, noise, IP address and MAC address.

DS-3WF01C-2N/O User Guide
11
Parameters Description
Items
Description
SN
It specifies the serial number of peer wireless bridge.
IPv4
It specifies the IP address of peer wireless bridge.
MAC Address
It specifies the MAC address of peer wireless bridge.
Signal Strength
It specifies the signal strength of peer wireless bridge.
Received Rate (Mbps)
It specifies the receiving rate of this wireless bridge.
Transmitted Rate
(Mbps)
It specifies the transmitting rate of this wireless bridge.
Noise (dBm)
It specifies the interference signal and electromagnet noise strength of peer
wireless device in the current environment. Larger absolute value indicates less
interference.

DS-3WF01C-2N/O User Guide
12
Chapter 4 Network
4.1 Overview
Log in to the web UI, and choose Network.
You can change the network parameters of this wireless bridge here, including IP address, subnet
mask, gateway and DNS server addresses here.
Parameters Description
Items
Description
IP Address
It specifies the IP address (also named management IP address) of this device.
Devices in LAN can use it to log in to the web UI of this wireless bridge. If you want
to enable this wireless bridge to access the internet, this IP address should be set to
an unused IP address which is in the same segment as that of the egress router.
Subnet Mask
It specifies the subnet mask of the wireless bridge. The default is 255.255.255.0.
Gateway
It specifies the default gateway of this wireless bridge. It is optional.
If you want to enable this wireless bridge to access the internet, the gateway should
be set to the LAN IP address of the egress router.

DS-3WF01C-2N/O User Guide
13
Items
Description
DNS1
It specifies the primary DNS server IP address of this wireless bridge. It is optional.
If you want to enable this wireless bridge to access the internet, and the egress
router supports DNS agent, you can enter the LAN IP address of the router here. If
the router does not support DNS agent, you need to enter a correct DNS IP address
here.
DNS2
It specifies the secondary DNS server IP address of this wireless bridge. It is
optional.
If you have two DNS server IP addresses, you can enter the other one here.
4.2 Changing the IP address
Assume that you need to change the IP address to 192.168.1.25.
Configuration procedure
Step 1 Choose Network.
Step 2 Change the IP Address to 192.168.1.25.
Step 3 Click Save.
----End
If you still want to configure the wireless bridge after changing the IP address, refer to the
following procedure:
*

DS-3WF01C-2N/O User Guide
14
If the new IP address is in the same network segment as that of the old one, refresh the page
and use the new IP address to log in to the web UI for configuration.
If the new IP address is in different network segment from that of the old one, set the IP
address of your management computer to an unused one which should be in the same
network segment as that of the new IP address of the wireless bridge. Then use the new IP
address of the wireless bridge to log in to the web UI for configuration.

DS-3WF01C-2N/O User Guide
15
Chapter 5 Wireless
5.1 Overview
Log in to the web UI, and choose Wireless.
You can change the wireless parameters of this wireless bridge here, including SSID, channel,
transmission power, and so on.
Parameters description
Items
Description
Operating Mode
It specifies the working mode the device operates. The wireless bridge works in AP
mode or CPE mode, and cannot be changed.
SSID
It specifies the wireless network name of this device. You can change it here.
After changing the SSID of this wireless bridge, you need to change the SSID of peer
wireless bridge as well. Otherwise, the wireless bridge fails to connect to peer one.