Hoist Fitness MC-7018 User manual

Fax
[phone]
[phone]
Customer Service
[phone]
RECORD SERIAL NUMBER HERE
MACHINE CODE
**WARNING!**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.
MC-7018
DIP STATION
OWNER'S MANUAL
Note: Both Serial Number and Model Number are Required when Ordering Parts
A01

02
04
10
11
12
13
15
16
ABBREVIATIONS...................................................................
OWNER'S MANUAL
PAGE 01 MC-7018 ASSEMBLY
LIMITED WARRANTY............................................................
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
CONTENTS

OWNER'S MANUAL
PAGE 02MC-7018 ASSEMBLY
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
TOOLS REQUIRED
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
INSTRUCTIONS

OWNER'S MANUAL
PAGE 03 MC-7018 ASSEMBLY
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

OWNER'S MANUAL
PAGE 04
MC-7018 ASSEMBLY
FRAME ASSEMBLY

- HAND TIGHTEN HARDWARE.
REMOVED FOR CLARITY.
- SOME PARTS MAY HAVE BEEN
FRAME ASSEMBLY
NOTE:
OWNER'S MANUAL
PAGE 05 MC-7018 ASSEMBLY
4
17
34
37
17
17
37
39
30 36 37
34
37
INSTALLATION IN THE NEXT STEPS.
3
17
37
39
2
6
IMPORTANT:
THE TIE WITH VERTICAL BOLT HOLES (3)
MUST BE INSTALLED IN THIS LOCATION.
IT WILL BE USED FOR THE SHELF
22
INSTALLATION IN THE NEXT STEPS.
LEFT HAND ASSEMBLY
22
34
37
17
17
37
39
30
36
37
34
37
17
3
17
37
39
2
RIGHT HAND ASSEMBLY
4
IMPORTANT:
THE TIE WITH VERTICAL BOLT HOLES (3)
MUST BE INSTALLED IN THIS LOCATION.
IT WILL BE USED FOR THE SHELF
6

MC-7012
*
*
*
*
*
*
*
*
*
3
*
2
4
*
*
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
* PARTS INCLUDED WITH THE
MC-7012
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
MC-7018 ASSEMBLY
OWNER'S MANUAL
PAGE 06
*
*
*
3
*
*
*
*
*
MC-7012
*
*
*
4
2
*
RIGHT HAND ASSEMBLYLEFT HAND ASSEMBLY

38
26
31
21
26
32
5
21
39
37
6
3
4
39
OWNER'S MANUAL
PAGE 07 MC-7018 ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FRAME ASSEMBLY

MC-7020
*
*
*
*
*
16
*
*
*
3
*
NOTE:
OTHER STATIONS MAY BE USED
IN PLACE OF THE MC-7020 AND
MC-7017.
MC-7017
MC-7018 ASSEMBLY
OWNER'S MANUAL
PAGE 08
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
* PARTS INCLUDED WITH THE MC-7020
AND MC-7017
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

OWNER'S MANUAL
PAGE 09
IT WILL BE NECESSARY TO LOOSEN SOME FRAME HARDWARE TO RE-ALIGN THE FRAME
AND RETIGHTEN BOLTS.
*IMPORTANT*
ASSURE THAT YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. IF NOT,
MC-7018 ASSEMBLY
NOW THAT THE MC-7018 IS COMPLETELY ASSEMBLED TAKE TIME TO
FRAME ASSEMBLY
REMOVED FOR CLARITY.
PARTS INCLUDED WITH THE MC-7020.
- SOME PARTS MAY HAVE BEEN
NOTE:
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE.
*
*
*
*
*
2
MC-7017
MC-7020
MC-7011
MC-7015
*
*
*
*
NOTE:
OTHER STATIONS MAY BE USED
IN PLACE OF THE MC-7020 AND
MC-7017.
8